|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
RE: Is there a solution to the "No response to MPS or EOP" problem?
Hi there,
I cannot offer a solution but I share the frustration of Phil since I can
reproduce this
exact problem with my setup:
Hylafax 4.0pl2 binary distribution included in SuSE Linux 6.0 (Kernel
2.0.36)
3Com US Robotics 56K Voice Faxmodem
This problem occurs reproducibly on certain analog fax machines. Even more
frustrating
is the fact that I did a cross check with the efax package. That worked ok
!!!
So either this is a Hylafax bug or a driver problem. In either case it is
sure that it can be
done since efax can do it. My config.ttyS0 is basically based on the USR20
template from
the config dirctory of the distribution with a small modification to get
across my PBX.
Any help or comment is greatly appreciated.
****************************************************************************
************
Two examples of affected fax machines:
Siemens FAX 940
T Fax 382L
****************************************************************************
*************
Transcript of failing fax transmissions:
Facsimile transmitted since 04/29/99 23:25:
Sender Pages Time Pg/min Errs TypRate TypData
stefan.swoboda@iteam.de 9 10:06 0.9 5 14400 1-D MR
---------------------------------------------------------------------
Total 9 10:06 0.9 5
Facsimile transmitted since last week:
Sender Pages Time Pg/min Errs TypRate TypData
root@silverwolf.iteam.de 8 2:54 2.8 0 9600 1-D MR
stefan.swoboda@iteam.de 12 10:53 1.1 5 14400 1-D MR
----------------------------------------------------------------------
Total 20 13:47 1.5 5
Facsimile received since 04/29/99 23:25:
Sender Pages Time Pg/min Errs TypRate TypData
+49 2236 604 820 3 1:04 2.8 0 14400 1-D MR
-----------------------------------------------------------
Total 3 1:04 2.8 0
Facsimile received since last week:
Sender Pages Time Pg/min Errs TypRate TypData
+49 211 43 50 653 6 1:37 3.7 0 14400 1-D MR
+49 2236 604 820 3 1:04 2.8 0 14400 1-D MR
------------------------------------------------------------
Total 9 2:41 3.4 0
Report failed calls and associated session logs:
To: stefan.swoboda@i Date: 04/30/99 20:25
Error: Communication failure during Phase B/C
---- Transcript of session follows ----
Apr 30 20:25:09.51: [ 1392]: SESSION BEGIN 00000021 492236604820
Apr 30 20:25:09.52: [ 1392]: SEND FAX: JOB 15 DEST 02236604820 COMMID
00000021
Apr 30 20:25:09.52: [ 1392]: MODEM set DTR OFF
Apr 30 20:25:09.52: [ 1392]: DELAY 2600 ms
Apr 30 20:25:12.12: [ 1392]: MODEM set DTR ON
Apr 30 20:25:12.12: [ 1392]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS, output flow RTS/CTS
Apr 30 20:25:12.12: [ 1392]: MODEM flush i/o
Apr 30 20:25:12.12: [ 1392]: <-- [17:ATE0V1Q0X3S0=0H0\r]
Apr 30 20:25:12.27: [ 1392]: --> [2:OK]
Apr 30 20:25:12.27: [ 1392]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=0&D2&C1\r]
Apr 30 20:25:12.42: [ 1392]: --> [2:OK]
Apr 30 20:25:12.42: [ 1392]: <-- [14:AT+FCLASS=2.0\r]
Apr 30 20:25:12.56: [ 1392]: --> [2:OK]
Apr 30 20:25:12.56: [ 1392]: <-- [9:AT+FLO=2\r]
Apr 30 20:25:12.70: [ 1392]: --> [2:OK]
Apr 30 20:25:12.70: [ 1392]: <-- [9:AT+FPP=0\r]
Apr 30 20:25:12.84: [ 1392]: --> [2:OK]
Apr 30 20:25:12.84: [ 1392]: <-- [9:AT+FBO=0\r]
Apr 30 20:25:12.98: [ 1392]: --> [2:OK]
Apr 30 20:25:12.98: [ 1392]: <-- [10:AT+FCT=30\r]
Apr 30 20:25:13.12: [ 1392]: --> [2:OK]
Apr 30 20:25:13.12: [ 1392]: <-- [15:AT+FNR=1,1,1,1\r]
Apr 30 20:25:13.26: [ 1392]: --> [2:OK]
Apr 30 20:25:13.26: [ 1392]: <-- [9:AT+FIE=0\r]
Apr 30 20:25:13.40: [ 1392]: --> [2:OK]
Apr 30 20:25:13.40: [ 1392]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Apr 30 20:25:13.55: [ 1392]: --> [2:OK]
Apr 30 20:25:13.55: [ 1392]: <-- [5:ATM0\r]
Apr 30 20:25:13.69: [ 1392]: --> [2:OK]
Apr 30 20:25:13.69: [ 1392]: MODEM input buffering enabled
Apr 30 20:25:13.69: [ 1392]: <-- [14:AT+FCLASS=2.0\r]
Apr 30 20:25:13.93: [ 1392]: --> [2:OK]
Apr 30 20:25:13.93: [ 1392]: <-- [9:AT+FLO=2\r]
Apr 30 20:25:14.17: [ 1392]: --> [2:OK]
Apr 30 20:25:14.17: [ 1392]: <-- [9:AT+FPP=0\r]
Apr 30 20:25:14.41: [ 1392]: --> [2:OK]
Apr 30 20:25:14.41: [ 1392]: <-- [9:AT+FBO=0\r]
Apr 30 20:25:14.65: [ 1392]: --> [2:OK]
Apr 30 20:25:14.65: [ 1392]: <-- [10:AT+FCT=30\r]
Apr 30 20:25:14.89: [ 1392]: --> [2:OK]
Apr 30 20:25:14.89: [ 1392]: <-- [15:AT+FNR=1,1,1,1\r]
Apr 30 20:25:15.13: [ 1392]: --> [2:OK]
Apr 30 20:25:15.13: [ 1392]: <-- [9:AT+FIE=0\r]
Apr 30 20:25:15.37: [ 1392]: --> [2:OK]
Apr 30 20:25:15.37: [ 1392]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Apr 30 20:25:15.62: [ 1392]: --> [2:OK]
Apr 30 20:25:15.62: [ 1392]: <-- [28:AT+FLI="HylaFax@silverwolf"\r]
Apr 30 20:25:15.87: [ 1392]: --> [2:OK]
Apr 30 20:25:15.87: [ 1392]: DIAL 02236604820
Apr 30 20:25:15.87: [ 1392]: <-- [17:ATDT002236604820\r]
Apr 30 20:25:27.82: [ 1392]: --> [4:+FCO]
Apr 30 20:25:30.52: [ 1392]: --> [19:+FNF:y^V^¿ ^S^P^E^V^ÍÀÐø^À^A]
Apr 30 20:25:30.52: [ 1392]: REMOTE NSF "y^V^¿ ^S^P^E^V^ÍÀÐø^À^A"
Apr 30 20:25:30.52: [ 1392]: --> [27:+FCI:" +49 2236 604 820"]
Apr 30 20:25:30.52: [ 1392]: REMOTE CSI "+49 2236 604 820"
Apr 30 20:25:30.52: [ 1392]: --> [20:+FIS:1,5,0,2,1,0,0,4]
Apr 30 20:25:30.52: [ 1392]: --> [2:OK]
Apr 30 20:25:30.52: [ 1392]: REMOTE best rate 14400 bit/s
Apr 30 20:25:30.52: [ 1392]: REMOTE max page width 1728 pixels in 215 mm
Apr 30 20:25:30.52: [ 1392]: REMOTE max unlimited page length
Apr 30 20:25:30.52: [ 1392]: REMOTE best vres 7.7 line/mm
Apr 30 20:25:30.52: [ 1392]: REMOTE best format 2-D MR
Apr 30 20:25:30.52: [ 1392]: REMOTE best 20 ms, 10 ms/scanline
Apr 30 20:25:30.52: [ 1392]: USE 14400 bit/s
Apr 30 20:25:30.52: [ 1392]: USE 20 ms, 10 ms/scanline
Apr 30 20:25:30.52: [ 1392]: SEND file "docq/doc25.ps;00"
Apr 30 20:25:30.52: [ 1392]: USE page width 1728 pixels in 215 mm
Apr 30 20:25:30.52: [ 1392]: USE unlimited page length
Apr 30 20:25:30.52: [ 1392]: USE 3.85 line/mm
Apr 30 20:25:30.52: [ 1392]: USE 1-D MR
Apr 30 20:25:30.52: [ 1392]: <-- [23:AT+FIS=0,5,0,2,0,0,0,4\r]
Apr 30 20:25:30.77: [ 1392]: --> [2:OK]
Apr 30 20:25:30.77: [ 1392]: <-- [7:AT+FDT\r]
Apr 30 20:25:31.05: [ 1392]: --> [20:+FCS:0,5,0,2,0,0,0,4]
Apr 30 20:25:38.02: [ 1392]: --> [7:CONNECT]
Apr 30 20:25:38.02: [ 1392]: SEND begin page
Apr 30 20:25:57.96: [ 1392]: SENT 24433 bytes of data
D 1D RTC
Apr 30 20:25:57.96: [ 1392]: SEND end page
Apr 30 20:25:57.96: [ 1392]: SEND send MPS (more pages, same document)
Apr 30 20:26:14.11: [ 1392]: --> [5:ERROR]
Apr 30 20:26:14.11: [ 1392]: SEND recv RTN (retrain negative)
Apr 30 20:26:14.11: [ 1392]: <-- [7:AT+FDT\r]
Apr 30 20:26:14.24: [ 1392]: --> [2:OK]
Apr 30 20:29:14.24: [ 1392]: MODEM TIMEOUT: reading line from modem
Apr 30 20:29:14.24: [ 1392]: MODEM <Timeout>
Apr 30 20:29:14.24: [ 1392]: <-- [7:AT+FKS\r]
Apr 30 20:29:14.48: [ 1392]: --> [2:OK]
Apr 30 20:29:14.48: [ 1392]: <-- [5:ATH0\r]
Apr 30 20:29:14.72: [ 1392]: --> [2:OK]
Apr 30 20:29:14.72: [ 1392]: MODEM set DTR OFF
Apr 30 20:29:14.72: [ 1392]: SESSION END
To: stefan.swoboda@i Date: 04/30/99 21:17
Error: No response to MPS repeated 3 times
---- Transcript of session follows ----
Apr 30 21:17:11.24: [ 1921]: SESSION BEGIN 00000029 492236604820
Apr 30 21:17:11.24: [ 1921]: SEND FAX: JOB 21 DEST 02236604820 COMMID
00000029
Apr 30 21:17:11.24: [ 1921]: MODEM set DTR OFF
Apr 30 21:17:11.24: [ 1921]: DELAY 2600 ms
Apr 30 21:17:13.84: [ 1921]: MODEM set DTR ON
Apr 30 21:17:13.84: [ 1921]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS, output flow RTS/CTS
Apr 30 21:17:13.84: [ 1921]: MODEM flush i/o
Apr 30 21:17:13.84: [ 1921]: <-- [17:ATE0V1Q0X3S0=0H0\r]
Apr 30 21:17:13.99: [ 1921]: --> [2:OK]
Apr 30 21:17:13.99: [ 1921]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=0&D2&C1\r]
Apr 30 21:17:14.14: [ 1921]: --> [2:OK]
Apr 30 21:17:14.14: [ 1921]: <-- [14:AT+FCLASS=2.0\r]
Apr 30 21:17:14.28: [ 1921]: --> [2:OK]
Apr 30 21:17:14.28: [ 1921]: <-- [9:AT+FLO=2\r]
Apr 30 21:17:14.42: [ 1921]: --> [2:OK]
Apr 30 21:17:14.42: [ 1921]: <-- [9:AT+FPP=0\r]
Apr 30 21:17:14.56: [ 1921]: --> [2:OK]
Apr 30 21:17:14.56: [ 1921]: <-- [9:AT+FBO=0\r]
Apr 30 21:17:14.70: [ 1921]: --> [2:OK]
Apr 30 21:17:14.70: [ 1921]: <-- [10:AT+FCT=30\r]
Apr 30 21:17:14.84: [ 1921]: --> [2:OK]
Apr 30 21:17:14.84: [ 1921]: <-- [15:AT+FNR=1,1,1,1\r]
Apr 30 21:17:14.98: [ 1921]: --> [2:OK]
Apr 30 21:17:14.98: [ 1921]: <-- [9:AT+FIE=0\r]
Apr 30 21:17:15.12: [ 1921]: --> [2:OK]
Apr 30 21:17:15.12: [ 1921]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Apr 30 21:17:15.27: [ 1921]: --> [2:OK]
Apr 30 21:17:15.27: [ 1921]: <-- [5:ATM0\r]
Apr 30 21:17:15.41: [ 1921]: --> [2:OK]
Apr 30 21:17:15.41: [ 1921]: MODEM input buffering enabled
Apr 30 21:17:15.41: [ 1921]: <-- [14:AT+FCLASS=2.0\r]
Apr 30 21:17:15.65: [ 1921]: --> [2:OK]
Apr 30 21:17:15.65: [ 1921]: <-- [9:AT+FLO=2\r]
Apr 30 21:17:15.89: [ 1921]: --> [2:OK]
Apr 30 21:17:15.89: [ 1921]: <-- [9:AT+FPP=0\r]
Apr 30 21:17:16.13: [ 1921]: --> [2:OK]
Apr 30 21:17:16.13: [ 1921]: <-- [9:AT+FBO=0\r]
Apr 30 21:17:16.37: [ 1921]: --> [2:OK]
Apr 30 21:17:16.37: [ 1921]: <-- [10:AT+FCT=30\r]
Apr 30 21:17:16.61: [ 1921]: --> [2:OK]
Apr 30 21:17:16.61: [ 1921]: <-- [15:AT+FNR=1,1,1,1\r]
Apr 30 21:17:16.85: [ 1921]: --> [2:OK]
Apr 30 21:17:16.85: [ 1921]: <-- [9:AT+FIE=0\r]
Apr 30 21:17:17.09: [ 1921]: --> [2:OK]
Apr 30 21:17:17.09: [ 1921]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Apr 30 21:17:17.34: [ 1921]: --> [2:OK]
Apr 30 21:17:17.34: [ 1921]: <-- [28:AT+FLI="HylaFax@silverwolf"\r]
Apr 30 21:17:17.59: [ 1921]: --> [2:OK]
Apr 30 21:17:17.59: [ 1921]: DIAL 02236604820
Apr 30 21:17:17.59: [ 1921]: <-- [17:ATDT002236604820\r]
Apr 30 21:17:29.59: [ 1921]: --> [4:+FCO]
Apr 30 21:17:32.28: [ 1921]: --> [19:+FNF:y^V^¿ ^S^P^E^V^ÍÀÐø^À^A]
Apr 30 21:17:32.28: [ 1921]: REMOTE NSF "y^V^¿ ^S^P^E^V^ÍÀÐø^À^A"
Apr 30 21:17:32.28: [ 1921]: --> [27:+FCI:" +49 2236 604 820"]
Apr 30 21:17:32.28: [ 1921]: REMOTE CSI "+49 2236 604 820"
Apr 30 21:17:32.28: [ 1921]: --> [20:+FIS:1,5,0,2,1,0,0,4]
Apr 30 21:17:32.28: [ 1921]: --> [2:OK]
Apr 30 21:17:32.28: [ 1921]: REMOTE best rate 14400 bit/s
Apr 30 21:17:32.28: [ 1921]: REMOTE max page width 1728 pixels in 215 mm
Apr 30 21:17:32.28: [ 1921]: REMOTE max unlimited page length
Apr 30 21:17:32.28: [ 1921]: REMOTE best vres 7.7 line/mm
Apr 30 21:17:32.28: [ 1921]: REMOTE best format 2-D MR
Apr 30 21:17:32.28: [ 1921]: REMOTE best 20 ms, 10 ms/scanline
Apr 30 21:17:32.28: [ 1921]: USE 14400 bit/s
Apr 30 21:17:32.28: [ 1921]: USE 20 ms, 10 ms/scanline
Apr 30 21:17:32.28: [ 1921]: SEND file "docq/doc37.ps;00"
Apr 30 21:17:32.28: [ 1921]: USE page width 1728 pixels in 215 mm
Apr 30 21:17:32.28: [ 1921]: USE unlimited page length
Apr 30 21:17:32.28: [ 1921]: USE 3.85 line/mm
Apr 30 21:17:32.28: [ 1921]: USE 1-D MR
Apr 30 21:17:32.28: [ 1921]: <-- [23:AT+FIS=0,5,0,2,0,0,0,4\r]
Apr 30 21:17:32.53: [ 1921]: --> [2:OK]
Apr 30 21:17:32.53: [ 1921]: <-- [7:AT+FDT\r]
Apr 30 21:17:32.81: [ 1921]: --> [20:+FCS:0,5,0,2,0,0,0,4]
Apr 30 21:17:39.78: [ 1921]: --> [7:CONNECT]
Apr 30 21:17:39.78: [ 1921]: SEND begin page
Apr 30 21:17:59.72: [ 1921]: SENT 24431 bytes of data
D RTC
Apr 30 21:17:59.72: [ 1921]: SEND end page
Apr 30 21:17:59.72: [ 1921]: SEND send MPS (more pages, same document)
Apr 30 21:18:21.10: [ 1921]: --> [7:+FHS:52]
Apr 30 21:18:21.10: [ 1921]: REMOTE HANGUP: No response to MPS repeated 3
times (code 52)
Apr 30 21:18:21.10: [ 1921]: <-- [5:ATH0\r]
Apr 30 21:18:21.22: [ 1921]: --> [2:OK]
Apr 30 21:18:21.22: [ 1921]: MODEM set DTR OFF
Apr 30 21:18:21.22: [ 1921]: SESSION END
To: stefan.swoboda@i Date: 04/30/99 21:22
Error: No response to MPS repeated 3 times
---- Transcript of session follows ----
Apr 30 21:22:08.97: [ 2007]: SESSION BEGIN 00000031 49211452776
Apr 30 21:22:08.98: [ 2007]: SEND FAX: JOB 23 DEST 452776 COMMID 00000031
Apr 30 21:22:08.98: [ 2007]: MODEM set DTR OFF
Apr 30 21:22:08.98: [ 2007]: DELAY 2600 ms
Apr 30 21:22:11.58: [ 2007]: MODEM set DTR ON
Apr 30 21:22:11.58: [ 2007]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS, output flow RTS/CTS
Apr 30 21:22:11.58: [ 2007]: MODEM flush i/o
Apr 30 21:22:11.58: [ 2007]: <-- [17:ATE0V1Q0X3S0=0H0\r]
Apr 30 21:22:11.73: [ 2007]: --> [2:OK]
Apr 30 21:22:11.73: [ 2007]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=0&D2&C1\r]
Apr 30 21:22:11.88: [ 2007]: --> [2:OK]
Apr 30 21:22:11.88: [ 2007]: <-- [14:AT+FCLASS=2.0\r]
Apr 30 21:22:12.02: [ 2007]: --> [2:OK]
Apr 30 21:22:12.02: [ 2007]: <-- [9:AT+FLO=2\r]
Apr 30 21:22:12.16: [ 2007]: --> [2:OK]
Apr 30 21:22:12.16: [ 2007]: <-- [9:AT+FPP=0\r]
Apr 30 21:22:12.30: [ 2007]: --> [2:OK]
Apr 30 21:22:12.30: [ 2007]: <-- [9:AT+FBO=0\r]
Apr 30 21:22:12.44: [ 2007]: --> [2:OK]
Apr 30 21:22:12.44: [ 2007]: <-- [10:AT+FCT=30\r]
Apr 30 21:22:12.58: [ 2007]: --> [2:OK]
Apr 30 21:22:12.58: [ 2007]: <-- [15:AT+FNR=1,1,1,1\r]
Apr 30 21:22:12.72: [ 2007]: --> [2:OK]
Apr 30 21:22:12.72: [ 2007]: <-- [9:AT+FIE=0\r]
Apr 30 21:22:12.86: [ 2007]: --> [2:OK]
Apr 30 21:22:12.86: [ 2007]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Apr 30 21:22:13.01: [ 2007]: --> [2:OK]
Apr 30 21:22:13.01: [ 2007]: <-- [5:ATM0\r]
Apr 30 21:22:13.15: [ 2007]: --> [2:OK]
Apr 30 21:22:13.15: [ 2007]: MODEM input buffering enabled
Apr 30 21:22:13.15: [ 2007]: <-- [14:AT+FCLASS=2.0\r]
Apr 30 21:22:13.39: [ 2007]: --> [2:OK]
Apr 30 21:22:13.39: [ 2007]: <-- [9:AT+FLO=2\r]
Apr 30 21:22:13.63: [ 2007]: --> [2:OK]
Apr 30 21:22:13.63: [ 2007]: <-- [9:AT+FPP=0\r]
Apr 30 21:22:13.87: [ 2007]: --> [2:OK]
Apr 30 21:22:13.87: [ 2007]: <-- [9:AT+FBO=0\r]
Apr 30 21:22:14.11: [ 2007]: --> [2:OK]
Apr 30 21:22:14.11: [ 2007]: <-- [10:AT+FCT=30\r]
Apr 30 21:22:14.35: [ 2007]: --> [2:OK]
Apr 30 21:22:14.35: [ 2007]: <-- [15:AT+FNR=1,1,1,1\r]
Apr 30 21:22:14.59: [ 2007]: --> [2:OK]
Apr 30 21:22:14.59: [ 2007]: <-- [9:AT+FIE=0\r]
Apr 30 21:22:14.83: [ 2007]: --> [2:OK]
Apr 30 21:22:14.83: [ 2007]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Apr 30 21:22:15.08: [ 2007]: --> [2:OK]
Apr 30 21:22:15.08: [ 2007]: <-- [28:AT+FLI="HylaFax@silverwolf"\r]
Apr 30 21:22:15.33: [ 2007]: --> [2:OK]
Apr 30 21:22:15.33: [ 2007]: DIAL 452776
Apr 30 21:22:15.33: [ 2007]: <-- [12:ATDT0452776\r]
Apr 30 21:22:27.68: [ 2007]: --> [4:+FCO]
Apr 30 21:22:30.65: [ 2007]: --> [24:+FNF:
^B^H^DI!^TRwo^?^?^?^?^?^?^B^B^P]
Apr 30 21:22:30.65: [ 2007]: REMOTE NSF "
^B^H^DI!^TRwo^?^?^?^?^?^?^B^B^P"
Apr 30 21:22:30.65: [ 2007]: --> [27:+FCI:" +49 211 452776"]
Apr 30 21:22:30.65: [ 2007]: REMOTE CSI "+49 211 452776"
Apr 30 21:22:30.65: [ 2007]: --> [20:+FIS:1,3,0,2,0,0,0,4]
Apr 30 21:22:30.65: [ 2007]: --> [2:OK]
Apr 30 21:22:30.65: [ 2007]: REMOTE best rate 9600 bit/s
Apr 30 21:22:30.65: [ 2007]: REMOTE max page width 1728 pixels in 215 mm
Apr 30 21:22:30.65: [ 2007]: REMOTE max unlimited page length
Apr 30 21:22:30.65: [ 2007]: REMOTE best vres 7.7 line/mm
Apr 30 21:22:30.65: [ 2007]: REMOTE best format 1-D MR
Apr 30 21:22:30.65: [ 2007]: REMOTE best 20 ms, 10 ms/scanline
Apr 30 21:22:30.65: [ 2007]: USE 9600 bit/s
Apr 30 21:22:30.65: [ 2007]: USE 20 ms, 10 ms/scanline
Apr 30 21:22:30.65: [ 2007]: SEND file "docq/doc41.ps;00"
Apr 30 21:22:30.65: [ 2007]: USE page width 1728 pixels in 215 mm
Apr 30 21:22:30.65: [ 2007]: USE unlimited page length
Apr 30 21:22:30.65: [ 2007]: USE 3.85 line/mm
Apr 30 21:22:30.65: [ 2007]: USE 1-D MR
Apr 30 21:22:30.65: [ 2007]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r]
Apr 30 21:22:30.90: [ 2007]: --> [2:OK]
Apr 30 21:22:30.90: [ 2007]: <-- [7:AT+FDT\r]
Apr 30 21:22:31.18: [ 2007]: --> [20:+FCS:0,3,0,2,0,0,0,4]
Apr 30 21:22:37.07: [ 2007]: --> [7:CONNECT]
Apr 30 21:22:37.07: [ 2007]: SEND begin page
Apr 30 21:23:01.19: [ 2007]: SENT 24432 bytes of data
Apr 30 21:23:01.19: [ 2007]: SEND 1D RTC
30 21:23:01.19: [ 2007]: SEND end page
Apr 30 21:23:01.19: [ 2007]: SEND send MPS (more pages, same document)
Apr 30 21:23:23.42: [ 2007]: --> [7:+FHS:52]
Apr 30 21:23:23.42: [ 2007]: REMOTE HANGUP: No response to MPS repeated 3
times (code 52)
Apr 30 21:23:23.42: [ 2007]: <-- [5:ATH0\r]
Apr 30 21:23:23.55: [ 2007]: --> [2:OK]
Apr 30 21:23:23.55: [ 2007]: MODEM set DTR OFF
Apr 30 21:23:23.55: [ 2007]: SESSION END
To: stefan.swoboda@i Date: 04/30/99 23:05
Error: No response to MPS repeated 3 times
---- Transcript of session follows ----
Apr 30 23:05:07.99: [ 2269]: SESSION BEGIN 00000033 49211452776
Apr 30 23:05:08.00: [ 2269]: SEND FAX: JOB 24 DEST 452776 COMMID 00000033
Apr 30 23:05:08.00: [ 2269]: MODEM set DTR OFF
Apr 30 23:05:08.00: [ 2269]: DELAY 2600 ms
Apr 30 23:05:10.60: [ 2269]: MODEM set DTR ON
Apr 30 23:05:10.60: [ 2269]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS, output flow RTS/CTS
Apr 30 23:05:10.60: [ 2269]: MODEM flush i/o
Apr 30 23:05:10.60: [ 2269]: <-- [17:ATE0V1Q0X3S0=0H0\r]
Apr 30 23:05:10.75: [ 2269]: --> [2:OK]
Apr 30 23:05:10.75: [ 2269]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=0&D2&C1\r]
Apr 30 23:05:10.90: [ 2269]: --> [2:OK]
Apr 30 23:05:10.90: [ 2269]: <-- [14:AT+FCLASS=2.0\r]
Apr 30 23:05:11.04: [ 2269]: --> [2:OK]
Apr 30 23:05:11.04: [ 2269]: <-- [9:AT+FLO=2\r]
Apr 30 23:05:11.18: [ 2269]: --> [2:OK]
Apr 30 23:05:11.18: [ 2269]: <-- [9:AT+FPP=0\r]
Apr 30 23:05:11.32: [ 2269]: --> [2:OK]
Apr 30 23:05:11.32: [ 2269]: <-- [9:AT+FBO=0\r]
Apr 30 23:05:11.46: [ 2269]: --> [2:OK]
Apr 30 23:05:11.46: [ 2269]: <-- [10:AT+FCT=30\r]
Apr 30 23:05:11.60: [ 2269]: --> [2:OK]
Apr 30 23:05:11.60: [ 2269]: <-- [15:AT+FNR=1,1,1,1\r]
Apr 30 23:05:11.74: [ 2269]: --> [2:OK]
Apr 30 23:05:11.74: [ 2269]: <-- [9:AT+FIE=0\r]
Apr 30 23:05:11.88: [ 2269]: --> [2:OK]
Apr 30 23:05:11.88: [ 2269]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Apr 30 23:05:12.03: [ 2269]: --> [2:OK]
Apr 30 23:05:12.03: [ 2269]: <-- [5:ATM0\r]
Apr 30 23:05:12.17: [ 2269]: --> [2:OK]
Apr 30 23:05:12.17: [ 2269]: MODEM input buffering enabled
Apr 30 23:05:12.17: [ 2269]: <-- [14:AT+FCLASS=2.0\r]
Apr 30 23:05:12.41: [ 2269]: --> [2:OK]
Apr 30 23:05:12.41: [ 2269]: <-- [9:AT+FLO=2\r]
Apr 30 23:05:12.65: [ 2269]: --> [2:OK]
Apr 30 23:05:12.65: [ 2269]: <-- [9:AT+FPP=0\r]
Apr 30 23:05:12.89: [ 2269]: --> [2:OK]
Apr 30 23:05:12.89: [ 2269]: <-- [9:AT+FBO=0\r]
Apr 30 23:05:13.13: [ 2269]: --> [2:OK]
Apr 30 23:05:13.13: [ 2269]: <-- [10:AT+FCT=30\r]
Apr 30 23:05:13.37: [ 2269]: --> [2:OK]
Apr 30 23:05:13.37: [ 2269]: <-- [15:AT+FNR=1,1,1,1\r]
Apr 30 23:05:13.61: [ 2269]: --> [2:OK]
Apr 30 23:05:13.61: [ 2269]: <-- [9:AT+FIE=0\r]
Apr 30 23:05:13.85: [ 2269]: --> [2:OK]
Apr 30 23:05:13.85: [ 2269]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Apr 30 23:05:14.10: [ 2269]: --> [2:OK]
Apr 30 23:05:14.10: [ 2269]: <-- [28:AT+FLI="HylaFax@silverwolf"\r]
Apr 30 23:05:14.35: [ 2269]: --> [2:OK]
Apr 30 23:05:14.35: [ 2269]: DIAL 452776
Apr 30 23:05:14.35: [ 2269]: <-- [12:ATDT0452776\r]
Apr 30 23:05:26.67: [ 2269]: --> [4:+FCO]
Apr 30 23:05:29.63: [ 2269]: --> [24:+FNF:
^B^H^DI!^TRwo^?^?^?^?^?^?^B^B^P]
Apr 30 23:05:29.63: [ 2269]: REMOTE NSF "
^B^H^DI!^TRwo^?^?^?^?^?^?^B^B^P"
Apr 30 23:05:29.63: [ 2269]: --> [27:+FCI:" +49 211 452776"]
Apr 30 23:05:29.63: [ 2269]: REMOTE CSI "+49 211 452776"
Apr 30 23:05:29.63: [ 2269]: --> [20:+FIS:1,3,0,2,0,0,0,4]
Apr 30 23:05:29.63: [ 2269]: --> [2:OK]
Apr 30 23:05:29.63: [ 2269]: REMOTE best rate 9600 bit/s
Apr 30 23:05:29.63: [ 2269]: REMOTE max page width 1728 pixels in 215 mm
Apr 30 23:05:29.63: [ 2269]: REMOTE max unlimited page length
Apr 30 23:05:29.63: [ 2269]: REMOTE best vres 7.7 line/mm
Apr 30 23:05:29.63: [ 2269]: REMOTE best format 1-D MR
Apr 30 23:05:29.63: [ 2269]: REMOTE best 20 ms, 10 ms/scanline
Apr 30 23:05:29.63: [ 2269]: USE 9600 bit/s
Apr 30 23:05:29.63: [ 2269]: USE 20 ms, 10 ms/scanline
Apr 30 23:05:29.63: [ 2269]: SEND file "docq/doc43.ps;00"
Apr 30 23:05:29.63: [ 2269]: USE page width 1728 pixels in 215 mm
Apr 30 23:05:29.63: [ 2269]: USE unlimited page length
Apr 30 23:05:29.63: [ 2269]: USE 3.85 line/mm
Apr 30 23:05:29.63: [ 2269]: USE 1-D MR
Apr 30 23:05:29.63: [ 2269]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r]
Apr 30 23:05:29.88: [ 2269]: --> [2:OK]
Apr 30 23:05:29.88: [ 2269]: <-- [7:AT+FDT\r]
Apr 30 23:05:30.16: [ 2269]: --> [20:+FCS:0,3,0,2,0,0,0,4]
Apr 30 23:05:35.73: [ 2269]: --> [20:+FCS:0,2,0,2,0,0,0,4]
Apr 30 23:05:41.64: [ 2269]: --> [7:CONNECT]
Apr 30 23:05:41.64: [ 2269]: SEND begin page
bytes of data
Apr 30 23:06:10.15: [ 2269]: SEND 1D RTC
Apr 30 23:06:10.15: [ 2269]: SEND end page
Apr 30 23:06:10.15: [ 2269]: SEND send MPS (more pages, same document)
Apr 30 23:06:33.43: [ 2269]: --> [7:+FHS:52]
Apr 30 23:06:33.43: [ 2269]: REMOTE HANGUP: No response to MPS repeated 3
times (code 52)
Apr 30 23:06:33.43: [ 2269]: <-- [5:ATH0\r]
Apr 30 23:06:33.55: [ 2269]: --> [2:OK]
Apr 30 23:06:33.55: [ 2269]: MODEM set DTR OFF
Apr 30 23:06:33.55: [ 2269]: SESSION END
To: stefan.swoboda@i Date: 04/30/99 23:14
Error: No response to MPS repeated 3 times
---- Transcript of session follows ----
Apr 30 23:14:03.58: [ 2629]: SESSION BEGIN 00000034 49211452776
Apr 30 23:14:03.58: [ 2629]: SEND FAX: JOB 25 DEST 452776 COMMID 00000034
Apr 30 23:14:03.58: [ 2629]: MODEM set DTR OFF
Apr 30 23:14:03.58: [ 2629]: DELAY 2600 ms
Apr 30 23:14:06.18: [ 2629]: MODEM set DTR ON
Apr 30 23:14:06.18: [ 2629]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS, output flow RTS/CTS
Apr 30 23:14:06.18: [ 2629]: MODEM flush i/o
Apr 30 23:14:06.18: [ 2629]: <-- [17:ATE0V1Q0X3S0=0H0\r]
Apr 30 23:14:06.33: [ 2629]: --> [2:OK]
Apr 30 23:14:06.33: [ 2629]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=0&D2&C1\r]
Apr 30 23:14:06.48: [ 2629]: --> [2:OK]
Apr 30 23:14:06.48: [ 2629]: <-- [14:AT+FCLASS=2.0\r]
Apr 30 23:14:06.62: [ 2629]: --> [2:OK]
Apr 30 23:14:06.62: [ 2629]: <-- [9:AT+FLO=2\r]
Apr 30 23:14:06.76: [ 2629]: --> [2:OK]
Apr 30 23:14:06.76: [ 2629]: <-- [9:AT+FPP=0\r]
Apr 30 23:14:06.90: [ 2629]: --> [2:OK]
Apr 30 23:14:06.90: [ 2629]: <-- [9:AT+FBO=0\r]
Apr 30 23:14:07.04: [ 2629]: --> [2:OK]
Apr 30 23:14:07.04: [ 2629]: <-- [10:AT+FCT=30\r]
Apr 30 23:14:07.18: [ 2629]: --> [2:OK]
Apr 30 23:14:07.18: [ 2629]: <-- [15:AT+FNR=1,1,1,0\r]
Apr 30 23:14:07.32: [ 2629]: --> [2:OK]
Apr 30 23:14:07.32: [ 2629]: <-- [9:AT+FIE=0\r]
Apr 30 23:14:07.46: [ 2629]: --> [2:OK]
Apr 30 23:14:07.46: [ 2629]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Apr 30 23:14:07.61: [ 2629]: --> [2:OK]
Apr 30 23:14:07.61: [ 2629]: <-- [5:ATM0\r]
Apr 30 23:14:07.75: [ 2629]: --> [2:OK]
Apr 30 23:14:07.75: [ 2629]: MODEM input buffering enabled
Apr 30 23:14:07.75: [ 2629]: <-- [14:AT+FCLASS=2.0\r]
Apr 30 23:14:07.99: [ 2629]: --> [2:OK]
Apr 30 23:14:07.99: [ 2629]: <-- [9:AT+FLO=2\r]
Apr 30 23:14:08.23: [ 2629]: --> [2:OK]
Apr 30 23:14:08.23: [ 2629]: <-- [9:AT+FPP=0\r]
Apr 30 23:14:08.47: [ 2629]: --> [2:OK]
Apr 30 23:14:08.47: [ 2629]: <-- [9:AT+FBO=0\r]
Apr 30 23:14:08.71: [ 2629]: --> [2:OK]
Apr 30 23:14:08.71: [ 2629]: <-- [10:AT+FCT=30\r]
Apr 30 23:14:08.95: [ 2629]: --> [2:OK]
Apr 30 23:14:08.95: [ 2629]: <-- [15:AT+FNR=1,1,1,0\r]
Apr 30 23:14:09.19: [ 2629]: --> [2:OK]
Apr 30 23:14:09.19: [ 2629]: <-- [9:AT+FIE=0\r]
Apr 30 23:14:09.43: [ 2629]: --> [2:OK]
Apr 30 23:14:09.43: [ 2629]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Apr 30 23:14:09.68: [ 2629]: --> [2:OK]
Apr 30 23:14:09.68: [ 2629]: <-- [28:AT+FLI="HylaFax@silverwolf"\r]
Apr 30 23:14:09.93: [ 2629]: --> [2:OK]
Apr 30 23:14:09.93: [ 2629]: DIAL 452776
Apr 30 23:14:09.93: [ 2629]: <-- [12:ATDT0452776\r]
Apr 30 23:14:22.30: [ 2629]: --> [4:+FCO]
Apr 30 23:14:25.25: [ 2629]: --> [27:+FCI:" +49 211 452776"]
Apr 30 23:14:25.25: [ 2629]: REMOTE CSI "+49 211 452776"
Apr 30 23:14:25.25: [ 2629]: --> [20:+FIS:1,3,0,2,0,0,0,4]
Apr 30 23:14:25.25: [ 2629]: --> [2:OK]
Apr 30 23:14:25.25: [ 2629]: REMOTE best rate 9600 bit/s
Apr 30 23:14:25.25: [ 2629]: REMOTE max page width 1728 pixels in 215 mm
Apr 30 23:14:25.25: [ 2629]: REMOTE max unlimited page length
Apr 30 23:14:25.25: [ 2629]: REMOTE best vres 7.7 line/mm
Apr 30 23:14:25.25: [ 2629]: REMOTE best format 1-D MR
Apr 30 23:14:25.25: [ 2629]: REMOTE best 20 ms, 10 ms/scanline
Apr 30 23:14:25.25: [ 2629]: USE 9600 bit/s
Apr 30 23:14:25.25: [ 2629]: USE 20 ms, 10 ms/scanline
Apr 30 23:14:25.25: [ 2629]: SEND file "docq/doc45.ps;00"
Apr 30 23:14:25.25: [ 2629]: USE page width 1728 pixels in 215 mm
Apr 30 23:14:25.25: [ 2629]: USE unlimited page length
Apr 30 23:14:25.25: [ 2629]: USE 3.85 line/mm
Apr 30 23:14:25.25: [ 2629]: USE 1-D MR
Apr 30 23:14:25.25: [ 2629]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r]
Apr 30 23:14:25.50: [ 2629]: --> [2:OK]
Apr 30 23:14:25.50: [ 2629]: <-- [7:AT+FDT\r]
Apr 30 23:14:25.78: [ 2629]: --> [20:+FCS:0,3,0,2,0,0,0,4]
Apr 30 23:14:31.69: [ 2629]: --> [7:CONNECT]
Apr 30 23:14:31.69: [ 2629]: SEND begin page
Apr 30 23:14:55.81: [ 2629]: SENT 24438 bytes of data
Apr 30 23:14:55.81: [ 2629]: SEND 1D RTC
Apr 30 23:14:55.81: [ 2629]: SEND end page
Apr 30 23:14:55.81: [ 2629]: SEND send MPS (more pages, same document)
.05: [ 2629]: --> [7:+FHS:52]
Apr 30 23:15:18.05: [ 2629]: REMOTE HANGUP: No response to MPS repeated 3
times (code 52)
Apr 30 23:15:18.05: [ 2629]: <-- [5:ATH0\r]
Apr 30 23:15:18.18: [ 2629]: --> [2:OK]
Apr 30 23:15:18.18: [ 2629]: MODEM set DTR OFF
Apr 30 23:15:18.18: [ 2629]: SESSION END
Nothing to purge in info directory.
Truncate merged session logs older than 30 days:
Nothing to purge in receive queue.
Nothing to purge in the tmp directory.
Destinations being rejected (added since 04/29/99 23:25):
Regards,
Stefan Swoboda
System Engineer
sswoboda@ford.com
Ford Motor Company
Tel.: +49 221 9034806
International Local Design & Implementation
Fax: +49 221 9033017
> -----Original Message-----
> From: Philip Rhoades [SMTP:philr@mail.austasia.net]
> Sent: 09 May 1999 03:26
> To: flexfax@sgi.com
> Subject: flexfax: Is there a solution to the "No response to MPS or
> EOP" problem?
>
> Hi all,
>
> I have looked at the archives but I can't find a solution to the problem I
> get sending to some fax machines ie:
>
> "Your facsimile job to 08-8232-2924 failed because:
> No response to MPS or EOP repeated 3 tries; Giving up after 3 attempts
> to send same page"
>
> I have tried a 3Com US Robotics 56K Voice Faxmodem and a Netcomm 56K
> Roadster with the same result.
>
> I seem to be getting this result about 25% of the time from various fax
> machines - some are new, some older.
>
> I will have to go back to paper faxing (which drives me crazy!) if I can't
> rely on a computer method.
>
> Thanks,
>
> Phil.
>
> Philip Rhoades
>
> Pricom Pty Limited (ACN 003 252 275)
> GPO Box 3411
> Sydney NSW 2001
> Australia
> Mobile: +61:0411-185-652
> Fax: +61:2:9959-4909
> E-mail: philr@mail.austasia.net
>
>
