flexfax: Hylafax cannot receive

["Stefan Frings" <sf@hans1.com>]

Hello,

 

I changed from Windows 98 to Linux and have problems using hylafax. I think that my modem is Ok because I could send and receive faxes using calss 1 and 2 on the microsoft fax program.

 

With class 2 I cannot send faxes. Hylafax sends the first page 3 times and aborts then. All 3 pages look very fine to the receiver. I did not try to receive faxes.

 

With class 1 I can send faxes but I cannot receive them. I tried two different fax devices to send them. My log-file looks like this one every time I try to receive a fax:

 

May 06 14:50:24.36: [ 268]: SESSION BEGIN 00000034 492119179439
May 06 14:50:24.36: [ 268]: <-- [4:ATA\r]
May 06 14:50:30.39: [ 268]: --> [7:CONNECT]
May 06 14:50:30.39: [ 268]: ANSWER: FAX CONNECTION
May 06 14:50:30.39: [ 268]: RECV FAX: begin
May 06 14:50:30.52: [ 268]: <-- data [23]
May 06 14:50:30.52: [ 268]: <-- data [2]
May 06 14:50:31.99: [ 268]: --> [7:CONNECT]
May 06 14:50:31.99: [ 268]: <-- data [10]
May 06 14:50:31.99: [ 268]: <-- data [2]
May 06 14:50:32.47: [ 268]: --> [2:OK]
May 06 14:50:32.47: [ 268]: <-- [9:AT+FRH=3\r]
May 06 14:50:32.85: [ 268]: --> [7:CONNECT]
May 06 14:50:34.33: [ 268]: --> [2:OK]
May 06 14:50:34.33: [ 268]: REMOTE TSI "0049 211 374025"
May 06 14:50:34.33: [ 268]: <-- [9:AT+FRH=3\r]
May 06 14:50:34.34: [ 268]: --> [7:CONNECT]
May 06 14:50:34.60: [ 268]: --> [2:OK]
May 06 14:50:34.60: [ 268]: REMOTE wants 14400 bit/s
May 06 14:50:34.60: [ 268]: REMOTE wants page width 1728 pixels in 215 mm
May 06 14:50:34.60: [ 268]: REMOTE wants unlimited page length
May 06 14:50:34.60: [ 268]: REMOTE wants 3.85 line/mm
May 06 14:50:34.60: [ 268]: REMOTE wants 2-D MR
May 06 14:50:34.60: [ 268]: RECV training at v.17 14400 bit/s
May 06 14:50:34.60: [ 268]: <-- [11:AT+FRM=145\r]
May 06 14:50:36.27: [ 268]: --> [7:CONNECT]
May 06 14:50:37.85: [ 268]: RECV: TCF 2786 bytes, 2% non-zero, 2705 zero-run
May 06 14:50:37.86: [ 268]: --> [10:NO CARRIER]
May 06 14:50:37.86: [ 268]: DELAY 75 ms
May 06 14:50:37.94: [ 268]: <-- [9:AT+FTH=3\r]
May 06 14:50:37.98: [ 268]: --> [7:CONNECT]
May 06 14:50:37.98: [ 268]: <-- data [3]
May 06 14:50:37.98: [ 268]: <-- data [2]
May 06 14:50:39.26: [ 268]: --> [2:OK]
May 06 14:50:39.26: [ 268]: TRAINING succeeded
May 06 14:50:39.26: [ 268]: <-- [11:AT+FRM=146\r]
May 06 14:50:40.05: [ 268]: --> [7:CONNECT]
May 06 14:50:40.05: [ 268]: RECV: begin page
May 06 14:50:51.36: [ 268]: RECV: 1132 total lines, 0 bad lines, 0 consecutive bad lines
May 06 14:50:51.36: [ 268]: RECV: end page
May 06 14:50:51.36: [ 268]: --> [10:NO CARRIER]
May 06 14:50:51.36: [ 268]: <-- [9:AT+FRH=3\r]
May 06 14:50:51.62: [ 268]: --> [7:CONNECT]
May 06 14:51:31.36: [ 268]: <-- data [1]
May 06 14:51:31.56: [ 268]: MODEM <Timeout>
May 06 14:51:31.56: [ 268]: RECV FAX (00000034): recvq/fax00006.tif from 0049 211 374025, route to <unspecified>, 0 pages in 1:01
May 06 14:51:31.58: [ 268]: RECV FAX: T.30 T2 timeout, expected page not received
May 06 14:51:31.58: [ 268]: <-- [9:AT+FTH=3\r]
May 06 14:51:31.59: [ 268]: --> [5:ERROR]
May 06 14:51:31.59: [ 268]: RECV FAX (00000034): session with 0049 211 374025 terminated abnormally: T.30 T2 timeout, expected page not received
May 06 14:51:31.59: [ 268]: RECV FAX: bin/faxrcvd "recvq/fax00006.tif" "modem" "00000034" "T.30 T2 timeout, expected page not received"
May 06 14:51:31.90: [ 268]: RECV FAX: end
May 06 14:51:31.90: [ 268]: SESSION END