|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Problem receiving multiple pages.
Problem
=3D=3D=3D=3D=3D=3D
I'm having problems getting HylaFAX to receive multiple pages. No =
errors show in the log file. Only the first page is created as a tif =
file. All other pages are not stored.
Already Attempted
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
I've tried changing the Class2RecvDataTrigger like this:
Class2RecvDataTrigger: \021
and like this
Class2RecvDataTrigger: \022
and pages after the first still aren't created, though the first page is =
created without problem. I tried this by a suggestion in the mailing =
list.
I upgraded the firmware, so this isn't the problem. Upgrading the =
firmware did solve an Unspecified Transmit Phase C error as well as an =
RSPREC invalid command error. We got one or other other randomly until =
we upgraded the firmware, and then it worked mostly correctly. That's =
the first place I'm going next time I have an error, is to upgrade =
firmware. Over the past few years we're still not sure how many of the =
errors were caused by invalid firmware.
Information
=3D=3D=3D=3D=3D=3D=3D=3D
I'm using a US Robotics 33.6 which sends faxes fine. We're using =
HylaFAX 4.0pl1 on an Silicon Graphics O2 running IRIX 6.3. The binaries =
were from the SGI FTP site in /sgi/fax. I'm using Ghostscript 3.33 as =
well, as suggested by the documentation.
Here's a sample log file..
Apr 19 12:35:24.48: [11469]: SESSION BEGIN 00000185 13033223245
Apr 19 12:35:24.48: [11469]: <-- [4:ATA\r]
Apr 19 12:35:33.81: [11469]: --> [4:+FCO]
Apr 19 12:35:33.81: [11469]: ANSWER: FAX CONNECTION
Apr 19 12:35:33.81: [11469]: STATE CHANGE: ANSWERING -> RECEIVING
Apr 19 12:35:33.81: [11469]: MODEM input buffering enabled
Apr 19 12:35:33.81: [11469]: RECV FAX: begin
Apr 19 12:35:35.81: [11469]: --> [27:+FTI:" 3033223245"]
Apr 19 12:35:35.81: [11469]: REMOTE TSI "3033223245"
Apr 19 12:35:35.81: [11469]: --> [20:+FCS:0,3,0,2,0,0,0,3]
Apr 19 12:35:35.81: [11469]: REMOTE wants 9600 bit/s
Apr 19 12:35:35.81: [11469]: REMOTE wants page width 1728 pixels in 215 =
mm
Apr 19 12:35:35.81: [11469]: REMOTE wants unlimited page length=20
Apr 19 12:35:35.81: [11469]: REMOTE wants 3.85 line/mm
Apr 19 12:35:35.81: [11469]: REMOTE wants 1-D MR
Apr 19 12:35:35.81: [11469]: --> [2:OK]
Apr 19 12:35:35.81: [11469]: <-- [7:AT+FDR\r]
Apr 19 12:35:40.21: [11469]: --> [7:CONNECT]
Apr 19 12:35:40.21: [11469]: RECV: begin page
Apr 19 12:35:40.21: [11469]: RECV: send trigger 0134
Apr 19 12:35:40.21: [11469]: <-- data [1]
Apr 19 12:36:07.51: [11469]: RECV: 32757 bytes of data, 1031 total lines
Apr 19 12:36:07.71: [11469]: RECV/CQ: Bad 1D pixel count, row 1055, got =
0, expec
ted 1728
Apr 19 12:36:07.71: [11469]: RECV/CQ: Bad 1D pixel count, row 1056, got =
0, expec
ted 1728
Apr 19 12:36:07.71: [11469]: RECV/CQ: Bad 1D pixel count, row 1057, got =
0, expec
ted 1728
Apr 19 12:36:07.71: [11469]: RECV/CQ: Bad 1D pixel count, row 1058, got =
0, expec
ted 1728
Apr 19 12:36:07.71: [11469]: RECV/CQ: Bad 1D pixel count, row 1059, got =
0, expec
ted 1728
Apr 19 12:36:07.71: [11469]: RECV: 304 bytes of data, 1060 total lines
Apr 19 12:36:07.71: [11469]: RECV/CQ: Adjusting for RTC found at row =
1054
Apr 19 12:36:07.71: [11469]: --> [17:+FPS:1,1062,0,0,0]
Apr 19 12:36:09.04: [11469]: --> [6:+FET:0]
Apr 19 12:36:09.04: [11469]: RECV recv MPS (more pages, same document)
Apr 19 12:36:09.04: [11469]: --> [2:OK]
Apr 19 12:36:09.07: [11469]: RECV send MCF (message confirmation)
Apr 19 12:36:09.07: [11469]: RECV FAX (00000185): from 3033223245, page =
1 in 0:3
4, INF, 3.85 line/mm, 1-D MR
Apr 19 12:36:09.08: [11469]: <-- [7:AT+FDR\r]
Apr 19 12:36:11.51: [11469]: --> [7:CONNECT]
Apr 19 12:36:11.51: [11469]: RECV: begin page
Apr 19 12:36:11.51: [11469]: RECV: send trigger 0134
Apr 19 12:36:11.51: [11469]: <-- data [1]
Apr 19 12:36:29.20: [11469]: RECV/CQ: Bad 1D pixel count, row 1051, got =
0, expec
ted 1728
Apr 19 12:36:29.21: [11469]: RECV/CQ: Bad 1D pixel count, row 1052, got =
0, expec
ted 1728
Apr 19 12:36:29.21: [11469]: RECV/CQ: Bad 1D pixel count, row 1053, got =
0, expec
ted 1728
Apr 19 12:36:29.21: [11469]: RECV/CQ: Bad 1D pixel count, row 1054, got =
0, expec
ted 1728
Apr 19 12:36:29.21: [11469]: RECV/CQ: Bad 1D pixel count, row 1055, got =
0, expec
ted 1728
Apr 19 12:36:29.21: [11469]: RECV: 21252 bytes of data, 1056 total lines
Apr 19 12:36:29.21: [11469]: RECV/CQ: Adjusting for RTC found at row =
1050
Apr 19 12:36:29.21: [11469]: --> [17:+FPS:1,1059,0,0,0]
Apr 19 12:36:30.50: [11469]: --> [6:+FET:2]
Apr 19 12:36:30.51: [11469]: RECV recv EOP (no more pages or documents)
Apr 19 12:36:30.51: [11469]: --> [2:OK]
Apr 19 12:36:30.54: [11469]: RECV send MCF (message confirmation)
Apr 19 12:36:30.54: [11469]: RECV FAX (00000185): from 3033223245, page =
2 in 0:2
1, INF, 3.85 line/mm, 1-D MR
Apr 19 12:36:30.55: [11469]: RECV FAX (00000185): recvq/fax00037.tif =
from 3033223245, route to <unspecified>, 2 pages in 0:57
Apr 19 12:36:30.55: [11469]: <-- [7:AT+FDR\r]
Apr 19 12:36:33.34: [11469]: --> [7:+FHS:00]
Apr 19 12:36:33.35: [11469]: REMOTE HANGUP: Normal and proper end of =
connection=20
(code 0)
Apr 19 12:36:33.35: [11469]: RECV FAX: bin/faxrcvd "recvq/fax00037.tif" =
"ttyf2"=20
"00000185" ""
Apr 19 12:36:33.72: [11469]: RECV FAX: end
Apr 19 12:36:33.72: [11469]: SESSION END
Here's the output of faxstat -r
gatekeeper 12# /usr/local/bin/faxstat -r
HylaFAX scheduler on gatekeeper.bmsc.com: Running
Modem ttyf2 (1.303.322.3245): Running and idle
Protect Page Owner Sender/TSI Recvd@ Filename
-rw-r-- 2 3 3033223245 17:58 fax00033.tif
-rw-r-- 1 3 3033223245 Tue09PM fax00023.tif
-rw-r-- 2 3 3033223245 17:49 fax00032.tif
-rw-r-- 1 3 3033223245 Tue09PM fax00022.tif
-rw-r-- 2 3 3033223245 17:47 fax00031.tif
-rw-r-- 2 3 3033223245 17:42 fax00030.tif
-rw-r-- 2 3 3033223245 18:36 fax00037.tif
-rw-r-- 2 3 3033223245 Thu06PM fax00027.tif
-rw-r-- 2 3 3033223245 18:34 fax00036.tif
-rw-r-- 3 3 3033223245 Thu12AM fax00026.tif
-rw-r-- 3 3 3033223245 18:31 fax00035.tif
-rw-r-- 1 3 3033223245 Wed10PM fax00025.tif
-rw-r-- 2 3 3033223245 18:01 fax00034.tif
-rw-r-- 1 3 3033223245 Tue09PM fax00024.tif
-rw-r-- 2 3 3033223245 Thu06PM fax00029.tif
-rw-r-- 2 3 3033223245 Thu06PM fax00028.tif
The files that show up with '2' or more for 'Page' were faxes that were =
multiple pages in length. However, only the first of those pages was =
properly received, and only one tif file shows up per session.
Configuration
=3D=3D=3D=3D=3D=3D=3D=3D=3D
The fax modem picks up, so I don't think the problem is in /etc/inittab, =
but here's the line anyway.
t2:23:respawn:/usr/local/sbin/faxgetty ttyf2
And here are the configuration lines from =
/var/spool/fax/etc/config.ttyf2
CountryCode: 1
AreaCode: 303
FAXNumber: 1.303.322.3245
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: "etc/dialrules"
ServerTracing: 1
SessionTracing: 0x1ffff
RecvFileMode: 0644
LogFileMode: 0644
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: high
GettyArgs: "-h %l dx_%s"
LocalIdentifier: BMSC
ClocalAsRoot: yes
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%p of %%t"
MaxRecvPages: 25
PercentGoodLines: 0
MaxConsecutiveBadLines: 1000000
ModemType: Class2.0 # use class 2.0 interface
ModemRate: 38400 # DCE-DTE communication rate
ModemFlowControl: rtscts # XON/XOFF flow control assumed
ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow =
control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow =
control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow =
control
ModemSetupDTRCmd: ATS13=3D1&D2 # setup so DTR drop resets =
modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier =
(or not)
ModemResultCodesCmd: ATQ0X4 # enable extended result codes
ModemResetCmds: ATS32=3D4&K1&M4
ModemWaitTimeCmd: ATS7=3D120
Class1TCFRecvTimeout: 1000000
Class2TCFRecvTimeout: 1000000
ModemSetupAACmd: AT+FAA=3D1
Class2NRCmd: AT+FNR=3D1,1,1,0
ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
Class2BUGCmd: AT+FBU=3D0
Class2CQQueryCmd: !(0),(0) # override modem response
