flexfax: Phase Errors

["Horst Simon" <hsimon@vic.bigpond.net.au>]

I have HylaFAX v4.0pl2 under RedHat 5.2, used pre-compiled binaries. I tried
2 different modems
with different results. Both modems are working with other packages, such as
Winfax, Bitware
and Tobit.
The modems are: Netcomm E7F and Banksia Blitzer V.32 MX-6. I get following
trace when receiving
faxes:
1. This trace is when using the Banksia modem:
An attempt to receive facsimile on cua1 failed because:

    Unspecified Receive Phase B error

    ---- Transcript of session follows ----

Feb 24 16:32:25.98: [  367]: SESSION BEGIN 00000007 61395531624
Feb 24 16:32:25.98: [  367]: <-- [4:ATA\r]
Feb 24 16:32:37.19: [  367]: --> [5:+FCON]
Feb 24 16:32:37.19: [  367]: ANSWER: FAX CONNECTION
Feb 24 16:32:37.20: [  367]: RECV FAX: begin
Feb 24 16:32:37.66: [  367]: --> [28:+FTSI:"                    "]
Feb 24 16:32:37.66: [  367]: REMOTE TSI ""
Feb 24 16:32:41.06: [  367]: --> [21:+FDCS:1,5,0,0,0,0,0,0]
Feb 24 16:32:41.06: [  367]: REMOTE wants 14400 bit/s
Feb 24 16:32:41.06: [  367]: REMOTE wants page width 1728 pixels in 215 mm
Feb 24 16:32:41.06: [  367]: REMOTE wants A4 page length (297 mm)
Feb 24 16:32:41.06: [  367]: REMOTE wants 7.7 line/mm
Feb 24 16:32:41.06: [  367]: REMOTE wants 1-D MR
Feb 24 16:32:41.06: [  367]: --> [2:OK]
Feb 24 16:32:41.07: [  367]: <-- [7:AT+FDR\r]
Feb 24 16:32:42.55: [  367]: --> [5:+FCFR]
Feb 24 16:32:49.33: [  367]: --> [8:+FHNG:70]
Feb 24 16:32:49.33: [  367]: REMOTE HANGUP: Unspecified Receive Phase B
error (code 70)
Feb 24 16:32:49.35: [  367]: RECV FAX (00000007): recvq/fax00007.tif from ,
route to <unspecified>, 0 pages in 0:12
Feb 24 16:32:49.40: [  367]: RECV FAX: Unspecified Receive Phase B error
Feb 24 16:32:49.40: [  367]: RECV FAX (00000007): session with  terminated
abnormally: Unspecified Receive Phase B error
Feb 24 16:32:49.40: [  367]: RECV FAX: bin/faxrcvd "recvq/fax00007.tif"
"cua1" "00000007" "Unspecified Receive Phase B error"

Following trace is when using the Netcomm modem:
An attempt to receive facsimile on cua1 failed because:

    Unspecified Phase C error, including too much delay between TCF and +FDR
command

    ---- Transcript of session follows ----

Feb 24 16:02:43.94: [  367]: SESSION BEGIN 00000006 61395531624
Feb 24 16:02:43.94: [  367]: <-- [4:ATA\r]
Feb 24 16:02:56.05: [  367]: --> [5:+FCON]
Feb 24 16:02:56.05: [  367]: ANSWER: FAX CONNECTION
Feb 24 16:02:56.06: [  367]: RECV FAX: begin
Feb 24 16:02:56.24: [  367]: --> [28:+FTSI:"+613 9553-1624      "]
Feb 24 16:02:56.24: [  367]: REMOTE TSI "+613 9553-1624"
Feb 24 16:02:56.24: [  367]: --> [21:+FDCS:1,3,0,2,0,0,0,3]
Feb 24 16:02:56.24: [  367]: REMOTE wants 9600 bit/s
Feb 24 16:02:56.25: [  367]: REMOTE wants page width 1728 pixels in 215 mm
Feb 24 16:02:56.25: [  367]: REMOTE wants unlimited page length
Feb 24 16:02:56.25: [  367]: REMOTE wants 7.7 line/mm
Feb 24 16:02:56.25: [  367]: REMOTE wants 1-D MR
Feb 24 16:02:58.14: [  367]: --> [2:OK]
Feb 24 16:02:58.14: [  367]: <-- [7:AT+FDR\r]
Feb 24 16:02:58.29: [  367]: --> [5:+FCFR]
Feb 24 16:03:00.60: [  367]: --> [7:CONNECT]
Feb 24 16:03:00.60: [  367]: RECV: begin page
Feb 24 16:03:00.60: [  367]: RECV: send trigger 021
Feb 24 16:03:29.13: [  367]: RECV: 225 total lines, 225 bad lines, 0
consecutive bad lines
Feb 24 16:03:30.40: [  367]: --> [16:+FPTS:1,2142,0,0]
Feb 24 16:03:30.40: [  367]: --> [6:+FET:2]
Feb 24 16:03:30.40: [  367]: RECV recv EOP (no more pages or documents)
Feb 24 16:03:30.40: [  367]: --> [2:OK]
Feb 24 16:03:30.41: [  367]: RECV: REJECT page quality, 0% good lines (95%
required)
Feb 24 16:03:30.41: [  367]: RECV send RTN (retrain negative)
Feb 24 16:03:30.41: [  367]: <-- [10:AT+FPTS=2\r]
Feb 24 16:03:33.48: [  367]: --> [9:+FHNG:100]
Feb 24 16:03:33.48: [  367]: REMOTE HANGUP: Unspecified Phase D error (code
100)
Feb 24 16:03:33.48: [  367]: --> [2:OK]
Feb 24 16:03:33.48: [  367]: <-- [7:AT+FDR\r]
Feb 24 16:06:33.48: [  367]: REMOTE HANGUP: Unspecified Phase C error,
including too much delay between TCF and +FDR command (code 90)
Feb 24 16:06:33.54: [  367]: RECV FAX (00000006): recvq/fax00006.tif from
+613 9553-1624, route to <unspecified>, 0 pages in 3:37
Feb 24 16:06:33.59: [  367]: RECV FAX: Unspecified Phase C error, including
too much delay between TCF and +FDR command
Feb 24 16:06:33.60: [  367]: RECV FAX (00000006): session with +613
9553-1624 terminated abnormally: Unspecified Phase C error, including too
much delay between TCF and +FDR command
Feb 24 16:06:33.60: [  367]: RECV FAX: bin/faxrcvd "recvq/fax00006.tif"
"cua1" "00000006" "Unspecified Phase C error, including too much delay
between TCF and +FDR command"

Is there any possible solution to get one of these modems working?

Thanks and Regards,
Horst Simon


===============================
|   Horst Simon               |
|   9 Stonehaven Crescent     |
|   Moorabbin, Vic, 3189      |
|   Australia                 |
|   hsimon@vic.bigpond.net.au |
===============================