Hylafax Mailing List Archives

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

AutoAnswer



Apologies for the repeat but i forgot to include my config file:

I have a USR 33.6 Faxmodem.  I have had many problems with config and here is a
file that sends faxes ok.  The question is what can I do to get the modem to
autoanswer.  It has worked for me in the past but I cannot seem to get it
working now. faxgetty is running.
The AA light just comes on but does not go off hook.
if I type faxanswer cua0, then it will answer.
Thank you

Eric Smith  


# $Id: usr-rts,v 1.6 1996/06/24 02:58:43 sam Rel $
#
# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and RTS/CTS flow control. 
#
# CONFIG:CLASS1:1444:.*:RTSCTS: Manufacturer=USRobotics Model=Courier/Sportster
# CONFIG:CLASS1:1445:.*:RTSCTS: Manufacturer=USRobotics Model=Courier/Sportster
# CONFIG:CLASS1:2886:.*:RTSCTS: Manufacturer=USRobotics Model=Courier/Sportster
# CONFIG:CLASS1:3366:.*:RTSCTS: Manufacturer=USRobotics Model=Courier
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use class 1 interface
ModemRate:		38400		# max rate for DCE-DTE communication
ModemFlowControl:	rtscts		# hardware flow control
#
ModemSetupDTRCmd:	ATS13=1&D2	# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no flow control
ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for hardware flow control
ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for software flow control
ModemResultCodesCmd:	ATQ0X4		# enable result codes
#
ModemMfrQueryCmd:	!USR
ModemModelQueryCmd:	ATI3
ModemRevQueryCmd:	ATI7		# XXX, returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:		AT&H0&I0&R1	# setup modem for no flow control
Class1HFLOCmd:		AT&H1&I0&R2	# setup modem for hardware flow control
Class1SFLOCmd:		""		# modem does this automatically
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.

#Eric fiddled here unsuccesfully to get AA to work
#ModemSetupAACmd:	AT+FCLASS=0&H1&I0&R2	# leave modem in class 0
#ModemAnswerFaxCmd:	ATA  # if null reads ModemAnswerCmd
#ModemAnswerCmd:		AT+FCLASS=1&H1&I0&R2A	# force RTS/CTS after change
#ModemAnswerCmd:		ATA	
#RingsBeforeAnswer:	1



Home
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services