flexfax: Can't send more than 1 page

[Lutz Kittler <Lutz.Kittler@sse-erfurt.de>]

Steven Pham writes:
 > Hi,
 > 
 > I'm having this anoying problem and trying to fix it but
 > without any luck, so please help.
 > 
 > The problem seems to be in Class20.c++ (I'm using USR
 > Sporter, class 2). If I send only 1 page, hylafax will send
 > out End Of Page (EOP) which will cause the remote fax machine
 > to hangup. If I send out more than one page, same problem,
 > hylafax will send out MPS (More pages, same document) which also
 > causes the remote fax machine to hangup with -->[7:+FHS:52]
 > 
 > It looks like Hylafax send out an unknown command which
 > cause the remote fax machine to hangup.
 > For EOP, Hylafax send out 2 bytes: 16 and 46
 > For MPS, Hylafax send out 2 bytes: 16 and 44
 > 
 > I have been tracing around Class20.c++, in pageDone() method
 > without much luck.
 > Can anyone help me please ......
 > 
Hi,

I also have a problem with one fax-machine after sending
MPS. I use fax class 2 . The first attempt to the same
device was alright. Other devices receive the same faxes
but at speed of 9600 bit/s.
May be there are problems because modem uses 14400 bit/s
( its a Telejet 14400 ). How can I tell the hylafax to
use 9600 bit / s ?
See the following protocol for error :

Oct 22 17:43:09.99: [ 3811]: SESSION BEGIN 00000009 4936203333
Oct 22 17:43:10.01: [ 3811]: SEND FAX: JOB 4 DEST 333 COMMID 00000009
Oct 22 17:43:10.01: [ 3811]: DELAY 2600 ms
Oct 22 17:43:12.62: [ 3811]: <-- [15:ATE0V1Q0S0=0H0\r]
Oct 22 17:43:12.77: [ 3811]: --> [2:OK]
Oct 22 17:43:12.77: [ 3811]: <-- [21:ATS8=2S7=60&K3&D3&C1\r]
Oct 22 17:43:12.92: [ 3811]: --> [2:OK]
Oct 22 17:43:12.92: [ 3811]: <-- [12:AT+FCLASS=2\r]
Oct 22 17:43:13.07: [ 3811]: --> [2:OK]
Oct 22 17:43:13.07: [ 3811]: <-- [10:AT+FTBC=0\r]
Oct 22 17:43:13.22: [ 3811]: --> [2:OK]
Oct 22 17:43:13.22: [ 3811]: <-- [10:AT+FBOR=0\r]
Oct 22 17:43:13.37: [ 3811]: --> [2:OK]
Oct 22 17:43:13.37: [ 3811]: <-- [13:AT+FPHCTO=30\r]
Oct 22 17:43:13.52: [ 3811]: --> [2:OK]
Oct 22 17:43:13.52: [ 3811]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Oct 22 17:43:13.67: [ 3811]: --> [2:OK]
Oct 22 17:43:13.67: [ 3811]: <-- [5:ATM0\r]
Oct 22 17:43:13.82: [ 3811]: --> [2:OK]
Oct 22 17:43:13.82: [ 3811]: <-- [12:AT+FCLASS=2\r]
Oct 22 17:43:14.07: [ 3811]: --> [2:OK]
Oct 22 17:43:14.07: [ 3811]: <-- [10:AT+FTBC=0\r]
Oct 22 17:43:14.32: [ 3811]: --> [2:OK]
Oct 22 17:43:14.32: [ 3811]: <-- [10:AT+FBOR=0\r]
Oct 22 17:43:14.57: [ 3811]: --> [2:OK]
Oct 22 17:43:14.57: [ 3811]: <-- [13:AT+FPHCTO=30\r]
Oct 22 17:43:14.82: [ 3811]: --> [2:OK]
Oct 22 17:43:14.82: [ 3811]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Oct 22 17:43:15.07: [ 3811]: --> [2:OK]
Oct 22 17:43:15.07: [ 3811]: <-- [20:AT+FLID="linux-fax"\r]
Oct 22 17:43:15.32: [ 3811]: --> [2:OK]
Oct 22 17:43:15.34: [ 3811]: DIAL 333
Oct 22 17:43:15.34: [ 3811]: <-- [8:ATDT333\r]
Oct 22 17:43:27.19: [ 3811]: --> [5:+FCON]
Oct 22 17:43:29.44: [ 3811]: --> [29:+FCSI: "     +49 36203 96333"]
Oct 22 17:43:29.44: [ 3811]: REMOTE CSI "+49 36203 96333"
Oct 22 17:43:29.83: [ 3811]: --> [22:+FDIS: 1,5,0,2,1,0,0,2]
Oct 22 17:43:29.83: [ 3811]: --> [2:OK]
Oct 22 17:43:29.83: [ 3811]: REMOTE best rate 14400 bit/s
Oct 22 17:43:29.83: [ 3811]: REMOTE max page width 1728 pixels in 215 mm
Oct 22 17:43:29.83: [ 3811]: REMOTE max unlimited page length 
Oct 22 17:43:29.84: [ 3811]: REMOTE best vres 7.7 line/mm
Oct 22 17:43:29.84: [ 3811]: REMOTE best format 2-D MR
Oct 22 17:43:29.84: [ 3811]: REMOTE best 10 ms, 5 ms/scanline
Oct 22 17:43:29.84: [ 3811]: USE 14400 bit/s
Oct 22 17:43:29.84: [ 3811]: USE 10 ms, 5 ms/scanline
Oct 22 17:43:29.84: [ 3811]: SEND file "docq/doc4.cover;40"
Oct 22 17:43:29.85: [ 3811]: USE page width 1728 pixels in 215 mm
Oct 22 17:43:29.85: [ 3811]: USE unlimited page length 
Oct 22 17:43:29.85: [ 3811]: USE 3.85 line/mm
Oct 22 17:43:29.85: [ 3811]: USE 2-D MR
Oct 22 17:43:29.86: [ 3811]: <-- [24:AT+FDIS=0,5,0,2,1,0,0,2\r]
Oct 22 17:43:30.11: [ 3811]: --> [2:OK]
Oct 22 17:43:30.11: [ 3811]: <-- [7:AT+FDT\r]
Oct 22 17:43:38.48: [ 3811]: --> [22:+FDCS: 0,5,0,2,1,0,0,3]
Oct 22 17:43:38.69: [ 3811]: --> [7:CONNECT]
Oct 22 17:43:38.69: [ 3811]: SEND wait for XON
Oct 22 17:43:38.69: [ 3811]: --> [1:]
Oct 22 17:43:38.69: [ 3811]: SEND begin page
Oct 22 17:43:41.71: [ 3811]: SENT 6872 bytes of data
Oct 22 17:43:41.71: [ 3811]: SEND end page
Oct 22 17:43:49.80: [ 3811]: --> [2:OK]
Oct 22 17:43:49.80: [ 3811]: SEND send MPS (more pages, same document)
Oct 22 17:43:49.80: [ 3811]: <-- [9:AT+FET=0\r]
Oct 22 17:43:57.30: [ 3811]: --> [8:+FHNG: 0]
Oct 22 17:43:57.30: [ 3811]: REMOTE HANGUP: Normal and proper end of connection (code 0)
Oct 22 17:43:57.30: [ 3811]: SEND recv unknown PPR 0x00
Oct 22 17:43:57.32: [ 3811]: SEND: Modem protocol error (unknown post-page response); Giving up after 3 attempts to send same page "docq/doc4.cover;40", dirnum 0
Oct 22 17:43:57.33: [ 3811]: <-- [5:ATH0\r]
Oct 22 17:43:57.49: [ 3811]: --> [2:OK]
Oct 22 17:43:57.49: [ 3811]: SESSION END

Many thanks in advance!

    Lutz