flexfax: Hylafax

[Don Linnell <dlinnell@ccs-llc.com>]

    I am currently running version 4.0 patch 2.2 of hylafax on an HP9000
K580 under HPUX 10.2.  I have a US Robotic 56K sporster modem.  I am
sending faxes at this point.  Unfortunately the fax machine is
stretching the letters like I'm watching an old western.  If anyone has
any ideas I would greatly appreciate it.  I'm using class 2.0 for the
fax interface.  Here is my modem config file.
    Thanks
        Don Linnell     don.linnell@ccs-llc.com

#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            1
AreaCode:               410
FAXNumber:              +1.999.555.1212
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          131071
SessionTracing:         131071
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "NothingSetup"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
QualifyTSI:             etc/tsi
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use this to supply a hint
ModemRate:              38400           # max rate for DCE-DTE
communication
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem

ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
(or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:           ATDT%s@         # T for tone dialing, @ for
silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
ModemResetCmds:         ""              # stuff to do when modem is
reset
ModemAnswerCmd:         ATA             # use this to answer phone
ModemNoFlowCmd:         AT&H0&I0&R1     # disable flow control cmd
ModemHardFlowCmd:       AT&H1&I0&R2     # hardware flow control cmd
ModemSoftFlowCmd:       AT&H2&I2&R1     # software flow control cmd
ModemNoAutoAnswerCmd:   ATS0=0          # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATM1 ATM1 ATM1 ATM1"
ModemEchoOffCmd:        ATE0            # disable command echo
ModemVerboseResultsCmd: ATV1            # enable verbose command results

ModemResultCodesCmd:    ATQ0X4          # enable result codes
ModemOnHookCmd:         ATH0            # place phone on hook (hangup)
ModemSoftResetCmd:      ATZ             # do soft reset of modem
ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds
ModemRecvFillOrder:     LSB2MSB         # bit order of received
facsimile
ModemSendFillOrder:     LSB2MSB         # bit order modem expects for
transmit
ModemSetupAACmd:        AT+FAA=1
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D
(direct)
Class2CQCmd:            ""              # commands to enable copy
quality proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       !(0),(0)        # override modem response
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=0        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities command

Class2DISCmd:           AT+FIS          # set session parameters command

Class2DDISCmd:          ""              # disable pre-dial DIS command
hack
Class2CIGCmd:           AT+FPI          # set polling identifier command

Class2NRCmd:            AT+FNR=1,1,1,1  # setup status reporting command

Class2PIECmd:           AT+FIE=0        # disable interrupt-enable
command
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control
command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control
command