flexfax: Unable to receive faxes.

[larsh@14xs.xs4all.nl]

Hi all !

been trying for weeks now. When I send myself  a fax from the web, my modem
picks up and tries to answer. After some time the remote modem gives up. I
tried it with different remote modems and faxes, it never works. I can send
faxes (sometimes) but this is not relieable as well.
My config: USR Sportster Voice 33.600, 
Configuration Profile...
Product type:  Netherlands Internal, Options: V32bis,V.FC,V.34+,x2
Fax Options: Class 1/Class 2.0, Clock Freq:  92.0Mhz, Eprom  256k,
Ram: 64k, EPROM date: 9/29/97,EPROM rev: 10.1.67
Using hylafax-v4.0pl2, running on Linux 2.0.33.
The modem is O.K., can receive send DATA at 56k.
I've attached my config, a receive log from my machine and a send log from
a remote modem.
Anybody got a clue of where to look ? I've tried it all (I think).

Thanx !
Lars Hameeteman.

Modem configuration for Hylafax:
CountryCode:            31
AreaCode:               10
FAXNumber:              +31.10.2907891
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        "etc/dialrules"
ServerTracing:          527
SessionTracing:         527
RecvFileMode:           0644
LogFileMode:            0600
DeviceMode:             0666
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-r -b -s %s %l"
LocalIdentifier:        "14XS-FAX"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
MaxRecvPages:           50
#
#
# Modem-related stuff: should reflect modem command interface
#
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              38400           # DCE-DTE communication rate
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
(or not)
ModemResultCodesCmd:    ATQ0X3          # enable extended result codes
#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
ModemSetupAACmd:        AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd:           AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd:       !(0),(0)        # override modem response
# End of file

Logfile of incoming fax:
Sep 13 13:04:12.72: [  322]: SESSION BEGIN 00000032 31102907891
Sep 13 13:04:12.72: [  322]: <-- [4:ATA\r]
Sep 13 13:07:12.72: [  322]: MODEM TIMEOUT: reading line from modem
Sep 13 13:07:12.72: [  322]: ANSWER: Ring detected without successful
handshake
Sep 13 13:07:12.72: [  322]: SESSION END

Logfile of remote modem:
Sep 13 11:02:30.61: [29858]: SESSION BEGIN 00166354 31102907891
Sep 13 11:02:30.61: [29858]: SEND FAX: JOB 18810 DEST +31102907891 COMMID
00166354
Sep 13 11:02:30.65: [29858]: DELAY 2600 ms
Sep 13 11:02:36.49: [29858]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 13 11:02:36.69: [29858]: --> [14:ATE0V1Q0S0=0H0]
Sep 13 11:02:36.69: [29858]: --> [2:OK]
Sep 13 11:02:36.69: [29858]: <-- [21:ATS8=2S7=60&E4&D3&C1\r]
Sep 13 11:02:36.89: [29858]: --> [2:OK]
Sep 13 11:02:36.89: [29858]: <-- [12:AT+FCLASS=2\r]
Sep 13 11:02:37.09: [29858]: --> [2:OK]
Sep 13 11:02:37.09: [29858]: <-- [10:AT+FTBC=0\r]
Sep 13 11:02:37.29: [29858]: --> [2:OK]
Sep 13 11:02:37.29: [29858]: <-- [10:AT+FBOR=0\r]
Sep 13 11:02:37.49: [29858]: --> [2:OK]
Sep 13 11:02:37.49: [29858]: <-- [13:AT+FPHCTO=30\r]
Sep 13 11:02:37.69: [29858]: --> [2:OK]
Sep 13 11:02:37.69: [29858]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Sep 13 11:02:37.89: [29858]: --> [2:OK]
Sep 13 11:02:37.89: [29858]: <-- [5:ATM0\r]
Sep 13 11:02:38.09: [29858]: --> [2:OK]
Sep 13 11:02:38.09: [29858]: <-- [12:AT+FCLASS=2\r]
Sep 13 11:02:38.29: [29858]: --> [2:OK]
Sep 13 11:02:38.29: [29858]: <-- [10:AT+FTBC=0\r]
Sep 13 11:02:38.49: [29858]: --> [2:OK]
Sep 13 11:02:38.49: [29858]: <-- [10:AT+FBOR=0\r]
Sep 13 11:02:38.69: [29858]: --> [2:OK]
Sep 13 11:02:38.69: [29858]: <-- [13:AT+FPHCTO=30\r]
Sep 13 11:02:38.89: [29858]: --> [2:OK]
Sep 13 11:02:38.89: [29858]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Sep 13 11:02:39.09: [29858]: --> [2:OK]
Sep 13 11:02:39.09: [29858]: <-- [25:AT+FLID="Demon Internet"\r]
Sep 13 11:02:39.29: [29858]: --> [2:OK]
Sep 13 11:02:39.29: [29858]: DIAL 0102907891
Sep 13 11:02:39.29: [29858]: <-- [16:ATDT0102907891@\r]
Sep 13 11:02:51.55: [29858]: --> [5:+FCON]
Sep 13 11:03:31.56: [29858]: REMOTE HANGUP: Unspecified Transmit Phase B
error (code 20)
Sep 13 11:03:31.56: [29858]: SEND FAILED: Unspecified Transmit Phase B error
Sep 13 11:03:31.56: [29858]: SEND FAILED: Unspecified Transmit Phase B
error; too many attempts to send
Sep 13 11:03:31.56: [29858]: <-- [5:ATH0\r]
Sep 13 11:03:33.07: [29858]: --> [7:+FHNG:2]
Sep 13 11:03:33.07: [29858]: REMOTE HANGUP: Call aborted,  from +FK or
<CAN> (code 2)
Sep 13 11:03:33.71: [29858]: --> [2:OK]
Sep 13 11:03:34.48: [29858]: SESSION END

--
Lars: Shit ! Ik kan m'n draadloze telefoon nergens vinden !
         Die ouwe was veel handiger !
         Die zat met een snoer aan de muur vast.............

.........I read. Therefor I know you exist.
Visit me at http://www.xs4all.nl/~larsh