|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Problem with modem-configuration
Hi,
I've got problems to get a new modem work with HylaFAX.
It's an ACEEX 2814V. It was a present and it has not a very well
documentation, but the manual says that it is compatible with
class 2. So I tested the class2 config file contributed with HylaFAX.
But it doesn't work :-( I also checked the rc288dpi config file but
this doesn't work either. I'm not familar with class2 fax setups , so
is there anybody who got this modem-type to work? Or any hints ?
I've included the session logs below.
It's not important to get the modem ready, I've got two other
modems working fine, but it would be nice to have a third line :-)
MfG
Michael
P.S. Excuse my poor english !Jeremy Allison schrieb:
--
Michael Mller A. Heinemann Heide GmbH & Co.KG
Unix-Systemadministrator Technische Gebudeausrstung
moeller.heinemann@t-online.de Sderdamm 5, 25746 Heide, Germany
D2:0172/4576755 Fax:05334/7485 oder 0481/87654 Tel.:0481/8571-0Syslog:
Feb 2 16:55:24 faxgate FaxGetty[3277]: STATE CHANGE: RUNNING -> LISTENING
Feb 2 16:55:24 faxgate FaxGetty[3277]: MODEM input buffering enabled
Feb 2 16:55:24 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:29 faxgate FaxGetty[3277]: MODEM TIMEOUT: reading line from modem
Feb 2 16:55:29 faxgate FaxGetty[3277]: <-- [5:ATH0\r]
Feb 2 16:55:29 faxgate FaxGetty[3277]: --> [5:ERROR]
Feb 2 16:55:29 faxgate FaxGetty[3277]: MODEM Command error
Feb 2 16:55:29 faxgate FaxGetty[3277]: MODEM set DTR OFF
Feb 2 16:55:29 faxgate FaxGetty[3277]: MODEM set DTR OFF
Feb 2 16:55:29 faxgate FaxGetty[3277]: DELAY 2600 ms
Feb 2 16:55:32 faxgate FaxGetty[3277]: MODEM set DTR ON
Feb 2 16:55:32 faxgate FaxGetty[3277]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
Feb 2 16:55:32 faxgate FaxGetty[3277]: MODEM flush i/o
Feb 2 16:55:32 faxgate FaxGetty[3277]: <-- [15:ATE0V1Q0S0=0H0\r]
Feb 2 16:55:32 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:32 faxgate FaxGetty[3277]: <-- [21:ATS8=2S7=60&K4&D2&C1\r]
Feb 2 16:55:32 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:32 faxgate FaxGetty[3277]: <-- [12:AT+FCLASS=?\r]
Feb 2 16:55:33 faxgate FaxGetty[3277]: --> [3:0,2]
Feb 2 16:55:33 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:33 faxgate FaxGetty[3277]: MODEM Supports "Data"
Feb 2 16:55:33 faxgate FaxGetty[3277]: MODEM Supports "Class 2"
Feb 2 16:55:33 faxgate FaxGetty[3277]: <-- [12:AT+FCLASS=2\r]
Feb 2 16:55:33 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:33 faxgate FaxGetty[3277]: <-- [9:AT+FMFR?\r]
Feb 2 16:55:33 faxgate FaxGetty[3277]: --> [5: ]
Feb 2 16:55:33 faxgate FaxGetty[3277]: <-- [9:AT+FMDL?\r]
Feb 2 16:55:33 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:33 faxgate FaxGetty[3277]: <-- [9:AT+FREV?\r]
Feb 2 16:55:33 faxgate FaxGetty[3277]: --> [14:V4.1 AUG-23-95]
Feb 2 16:55:33 faxgate FaxGetty[3277]: --> [88:DM2814/2A/RC288DPI V.34/PCB:490-22801-xx or 490-22802-xx or 490-21407-xx or 490-21420-xx]
Feb 2 16:55:33 faxgate FaxGetty[3277]: --> [40:BZT POSTZULASSUNG-FIRMWARE VERSION:V.105]
Feb 2 16:55:33 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:33 faxgate FaxGetty[3277]: MODEM: Revision V4.1 AUG-23-95 DM2814/2A/RC288DPI V.34/PCB:490-22801-xx or 490-22802-xx or 490-21407-xx or 490-21420-xx BZT POSTZULASSUNG-FIRMWARE VERSION:V.105
Feb 2 16:55:33 faxgate FaxGetty[3277]: <-- [10:AT+FDCC=?\r]
Feb 2 16:55:34 faxgate FaxGetty[3277]: --> [43:(0-1),(0-5),(0-3),(0-2),(0-2),(0),(0),(0-7)]
Feb 2 16:55:34 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 3.85 line/mm
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 7.7 line/mm
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 2400 bit/s
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 4800 bit/s
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 7200 bit/s
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 9600 bit/s
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 12000 bit/s
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 14400 bit/s
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports page width 1728 pixels in 215 mm
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports page width 2048 pixels in 255 mm
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports page width 2432 pixels in 303 mm
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports page width 1216 pixels in 151 mm
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports A4 page length (297 mm)
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports B4 page length (364 mm)
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports unlimited page length
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 1-D MR
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 2-D MR
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 2-D Uncompressed Mode
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 0 ms/scanline
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 5 ms/scanline
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 10 ms, 5 ms/scanline
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 10 ms/scanline
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 20 ms, 10 ms/scanline
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 20 ms/scanline
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 40 ms, 20 ms/scanline
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports 40 ms/scanline
Feb 2 16:55:34 faxgate FaxGetty[3277]: <-- [9:AT+FCQ=?\r]
Feb 2 16:55:34 faxgate FaxGetty[3277]: --> [5:ERROR]
Feb 2 16:55:34 faxgate FaxGetty[3277]: MODEM Supports no copy quality checking
Feb 2 16:55:34 faxgate FaxGetty[3277]: <-- [9:AT+FAP=?\r]
Feb 2 16:55:34 faxgate FaxGetty[3277]: --> [3:060]
Feb 2 16:55:34 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:34 faxgate FaxGetty[3277]: <-- [10:AT+FSPL=?\r]
Feb 2 16:55:34 faxgate FaxGetty[3277]: --> [5:ERROR]
Feb 2 16:55:34 faxgate FaxGetty[3277]: <-- [12:AT+FCLASS=2\r]
Feb 2 16:55:35 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:35 faxgate FaxGetty[3277]: <-- [10:AT+FTBC=0\r]
Feb 2 16:55:35 faxgate FaxGetty[3277]: --> [5:ERROR]
Feb 2 16:55:35 faxgate FaxGetty[3277]: MODEM Command error
Feb 2 16:55:35 faxgate FaxGetty[3277]: <-- [10:AT+FBOR=0\r]
Feb 2 16:55:35 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:35 faxgate FaxGetty[3277]: <-- [13:AT+FPHCTO=30\r]
Feb 2 16:55:35 faxgate FaxGetty[3277]: --> [5:ERROR]
Feb 2 16:55:35 faxgate FaxGetty[3277]: MODEM Command error
Feb 2 16:55:35 faxgate FaxGetty[3277]: <-- [10:AT+FBUG=1\r]
Feb 2 16:55:36 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:36 faxgate FaxGetty[3277]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Feb 2 16:55:36 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:36 faxgate FaxGetty[3277]: MODEM /V4.1 AUG-23-95 DM2814/2A/RC288DPI V.34/PCB:490-22801-xx or 490-22802-xx or 490-21407-xx or 490-21420-xx BZT POSTZULASSUNG-FIRMWARE VERSION:V.105
Feb 2 16:55:36 faxgate FaxGetty[3277]: <-- [5:ATM0\r]
Feb 2 16:55:36 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:36 faxgate FaxGetty[3277]: <-- [10:AT+FREL=1\r]
Feb 2 16:55:36 faxgate FaxGetty[3277]: --> [5: ]
Feb 2 16:55:36 faxgate FaxGetty[3277]: MODEM <Empty line>
Feb 2 16:55:36 faxgate FaxGetty[3277]: <-- [9:AT+FCR=1\r]
Feb 2 16:55:36 faxgate FaxGetty[3277]: --> [5:ERROR]
Feb 2 16:55:36 faxgate FaxGetty[3277]: MODEM Command error
Feb 2 16:55:36 faxgate FaxGetty[3277]: <-- [31:AT+FLID="A. Heinemann Heide +"\r]
Feb 2 16:55:37 faxgate FaxGetty[3277]: --> [2:OK]
Feb 2 16:55:37 faxgate FaxGetty[3277]: STATE CHANGE: LISTENING -> RUNNING
Feb 2 16:55:37 faxgate FaxGetty[3277]: MODEM input buffering disabled
config.edv.modem
CountryCode: 49
AreaCode: 481
FAXNumber: +49.481.8571.42
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: "etc/dialrules"
ServerTracing: 511
SessionTracing: 511
RecvFileMode: 0666
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "A. Heinemann Heide +49.481.8571-41"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "Von %%l|%c|Seite %%p von %%t"
PercentGoodLines: 80
MaxConsecutiveBadLines: 20
MaxRecvPages: 250
#
ModemType: Class2 # use this to supply a hint
ModemRate: 19200 # max rate for DCE-DTE communication
ModemFlowControl: xonxoff # XON/XOFF flow control assumed
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
#
ModemDialCmd: ATDT%s # T for tone dialing, @ for silence
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds: "" # stuff to do when modem is reset
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT&K # disable flow control cmd
ModemHardFlowCmd: AT&K3 # hardware flow control cmd
ModemSoftFlowCmd: AT&K4 # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0 # enable result codes
ModemOnHookCmd: ATH0 # place phone on hook (hangup)
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd: AT+FCLASS=2 # command to enter class 2
Class2BORCmd: AT+FBOR=0 # bit order for phase B/C/D (direct)
Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FK # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities
Class2TBCCmd: AT+FTBC=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLID # set local identifier command
Class2DCCCmd: AT+FDCC # set modem capabilities command
Class2DISCmd: AT+FDIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FCIG # set polling identifier command
Class2PTSCmd: AT+FPTS # set post-page status command
Class2SPLCmd: AT+FSPL # set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger: "" # character sent to modem to start recv
Class2XmitWaitForXON: yes # if true, wait for XON before send
Log :
Feb 02 16:54:55.02: [ 3770]: SESSION BEGIN 00008484 4948152
Feb 02 16:54:55.02: [ 3770]: SEND FAX: JOB 2526 DEST 52 COMMID 00008484
Feb 02 16:54:55.02: [ 3770]: MODEM set DTR OFF
Feb 02 16:54:55.02: [ 3770]: DELAY 2600 ms
Feb 02 16:54:57.62: [ 3770]: MODEM set DTR ON
Feb 02 16:54:57.63: [ 3770]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
Feb 02 16:54:57.63: [ 3770]: MODEM flush i/o
Feb 02 16:54:57.63: [ 3770]: <-- [15:ATE0V1Q0S0=0H0\r]
Feb 02 16:54:57.78: [ 3770]: --> [2:OK]
Feb 02 16:54:57.78: [ 3770]: <-- [21:ATS8=2S7=60&K4&D2&C1\r]
Feb 02 16:54:57.93: [ 3770]: --> [2:OK]
Feb 02 16:54:57.93: [ 3770]: <-- [12:AT+FCLASS=2\r]
Feb 02 16:54:58.07: [ 3770]: --> [2:OK]
Feb 02 16:54:58.07: [ 3770]: <-- [10:AT+FTBC=0\r]
Feb 02 16:54:58.21: [ 3770]: --> [5:ERROR]
Feb 02 16:54:58.21: [ 3770]: MODEM Command error
Feb 02 16:54:58.21: [ 3770]: <-- [10:AT+FBOR=0\r]
Feb 02 16:54:58.35: [ 3770]: --> [2:OK]
Feb 02 16:54:58.35: [ 3770]: <-- [13:AT+FPHCTO=30\r]
Feb 02 16:54:58.50: [ 3770]: --> [5:ERROR]
Feb 02 16:54:58.50: [ 3770]: MODEM Command error
Feb 02 16:54:58.50: [ 3770]: <-- [10:AT+FBUG=1\r]
Feb 02 16:54:58.64: [ 3770]: --> [2:OK]
Feb 02 16:54:58.64: [ 3770]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Feb 02 16:54:58.79: [ 3770]: --> [2:OK]
Feb 02 16:54:58.79: [ 3770]: <-- [5:ATM0\r]
Feb 02 16:54:58.93: [ 3770]: --> [2:OK]
Feb 02 16:54:58.93: [ 3770]: STATE CHANGE: RUNNING -> SENDING
Feb 02 16:54:58.93: [ 3770]: MODEM input buffering enabled
Feb 02 16:54:58.94: [ 3770]: <-- [12:AT+FCLASS=2\r]
Feb 02 16:54:59.17: [ 3770]: --> [2:OK]
Feb 02 16:54:59.17: [ 3770]: <-- [10:AT+FTBC=0\r]
Feb 02 16:54:59.41: [ 3770]: --> [5:ERROR]
Feb 02 16:54:59.41: [ 3770]: MODEM Command error
Feb 02 16:54:59.41: [ 3770]: <-- [10:AT+FBOR=0\r]
Feb 02 16:54:59.65: [ 3770]: --> [2:OK]
Feb 02 16:54:59.65: [ 3770]: <-- [13:AT+FPHCTO=30\r]
Feb 02 16:54:59.90: [ 3770]: --> [5:ERROR]
Feb 02 16:54:59.90: [ 3770]: MODEM Command error
Feb 02 16:54:59.90: [ 3770]: <-- [10:AT+FBUG=1\r]
Feb 02 16:55:00.14: [ 3770]: --> [2:OK]
Feb 02 16:55:00.14: [ 3770]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Feb 02 16:55:00.39: [ 3770]: --> [2:OK]
Feb 02 16:55:00.39: [ 3770]: <-- [31:AT+FLID="A. Heinemann Heide +"\r]
Feb 02 16:55:00.65: [ 3770]: --> [2:OK]
Feb 02 16:55:00.66: [ 3770]: DIAL 52
Feb 02 16:55:00.66: [ 3770]: <-- [7:ATDT52\r]
Feb 02 16:55:15.24: [ 3770]: --> [54:+FHR: FF 03 20 00 00 21 01 0C 02 27 08 02 9F BC 04 30 ]
Feb 02 16:55:15.24: [ 3770]: --> [48:30 30 30 10 44 49 45 48 20 4E 4E 41 4D 45 4E 49 ]
Feb 02 16:55:15.25: [ 3770]: SEND FAILED: Unknown problem (check modem power)
Feb 02 16:55:15.25: [ 3770]: <-- [5:ATH0\r]
Feb 02 16:55:16.27: [ 3770]: --> [78:45 48 20 41 01 02 01 08 B8 B5 FF 03 40 34 35 36 37 38 20 31 38 34 20 39 34 20 ]
Feb 02 16:55:16.27: [ 3770]: --> [54:20 20 20 20 20 20 20 CC 60 FF 13 80 00 CE E8 04 B1 BD ]
Feb 02 16:55:16.27: [ 3770]: --> [3:CED]
Feb 02 16:55:16.27: [ 3770]: --> [5:+FCON]
Feb 02 16:55:16.49: [ 3770]: --> [19:+FNSF: 00 00 21 01 ]
Feb 02 16:55:16.49: [ 3770]: --> [27:+FCSI: 49 481 87654]
Feb 02 16:55:16.49: [ 3770]: --> [22:+FDIS: 1,3,0,2,2,2,0,3]
Feb 02 16:55:16.49: [ 3770]: --> [2:OK]
Feb 02 16:55:16.50: [ 3770]: MODEM set DTR OFF
Feb 02 16:55:16.50: [ 3770]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Feb 02 16:55:16.50: [ 3770]: SESSION END
