Hylafax Mailing List Archives

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: Unspecified Transmit Phase B error



I guees I'll answer my own question the following line in
cuaa0/config:



Class2NRCmd:            AT+FNR=1,1,1,0  # setup status reporting command


JH

John Hazard writes:
 > 
 > 
 > I am having problems with HylaFax on a freebsd machine.  As you can
 > see below it connects, but quits pretty quickly.  
 > 
 > I have tried to 2 "good" fax machines.  The modem handles data ok,
 > i.e. I can dial an ISP.  The fax  modem is also OK under Windows 95.
 > 
 > 
 > The modem config file is at the end, but here is the head of that file:
 > 
 > #
 > # Configuration for using the Class 2.0 command interface
 > # with a USR v.34 Courier or Sporster modem.
 > #
 > # RTS/CTS flow control is used default.
 > #
 > #
 > 
 > Your facsimile job to 5551616 failed because:
 >     Unspecified Transmit Phase B error; too many attempts to send
 > 
 >     ---- Transcript of session follows ----
 > 
 > Oct 16 09:19:06.62: [13816]: SESSION BEGIN 00000007 15105551616
 > Oct 16 09:19:06.62: [13816]: SEND FAX: JOB 2 DEST 5551616 COMMID 00000007
 > Oct 16 09:19:06.62: [13816]: DELAY 2600 ms
 > Oct 16 09:19:09.23: [13816]: <-- [17:ATE0V1Q0X4S0=0H0\r]
 > Oct 16 09:19:09.37: [13816]: --> [2:OK]
 > Oct 16 09:19:09.37: [13816]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
 > Oct 16 09:19:09.51: [13816]: --> [2:OK]
 > Oct 16 09:19:09.51: [13816]: <-- [14:AT+FCLASS=2.0\r]
 > Oct 16 09:19:09.64: [13816]: --> [2:OK]
 > Oct 16 09:19:09.64: [13816]: <-- [9:AT+FLO=2\r]
 > Oct 16 09:19:09.77: [13816]: --> [2:OK]
 > Oct 16 09:19:09.77: [13816]: <-- [9:AT+FPP=0\r]
 > Oct 16 09:19:09.90: [13816]: --> [2:OK]
 > Oct 16 09:19:09.90: [13816]: <-- [9:AT+FBO=0\r]
 > Oct 16 09:19:10.03: [13816]: --> [2:OK]
 > Oct 16 09:19:10.03: [13816]: <-- [10:AT+FCT=30\r]
 > Oct 16 09:19:10.17: [13816]: --> [2:OK]
 > Oct 16 09:19:10.17: [13816]: <-- [15:AT+FNR=1,1,1,1\r]
 > Oct 16 09:19:10.31: [13816]: --> [2:OK]
 > Oct 16 09:19:10.31: [13816]: <-- [9:AT+FIE=0\r]
 > Oct 16 09:19:10.44: [13816]: --> [2:OK]
 > Oct 16 09:19:10.44: [13816]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
 > Oct 16 09:19:10.58: [13816]: --> [2:OK]
 > Oct 16 09:19:10.58: [13816]: <-- [5:ATM0\r]
 > Oct 16 09:19:10.71: [13816]: --> [2:OK]
 > Oct 16 09:19:10.72: [13816]: <-- [14:AT+FCLASS=2.0\r]
 > Oct 16 09:19:10.96: [13816]: --> [2:OK]
 > Oct 16 09:19:10.96: [13816]: <-- [9:AT+FLO=2\r]
 > Oct 16 09:19:11.19: [13816]: --> [2:OK]
 > Oct 16 09:19:11.19: [13816]: <-- [9:AT+FPP=0\r]
 > Oct 16 09:19:11.42: [13816]: --> [2:OK]
 > Oct 16 09:19:11.42: [13816]: <-- [9:AT+FBO=0\r]
 > Oct 16 09:19:11.65: [13816]: --> [2:OK]
 > Oct 16 09:19:11.65: [13816]: <-- [10:AT+FCT=30\r]
 > Oct 16 09:19:11.89: [13816]: --> [2:OK]
 > Oct 16 09:19:11.89: [13816]: <-- [15:AT+FNR=1,1,1,1\r]
 > Oct 16 09:19:12.13: [13816]: --> [2:OK]
 > Oct 16 09:19:12.13: [13816]: <-- [9:AT+FIE=0\r]
 > Oct 16 09:19:12.36: [13816]: --> [2:OK]
 > Oct 16 09:19:12.36: [13816]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
 > Oct 16 09:19:12.60: [13816]: --> [2:OK]
 > Oct 16 09:19:12.60: [13816]: <-- [16:AT+FLI="Hazard"\r]
 > Oct 16 09:19:12.84: [13816]: --> [2:OK]
 > Oct 16 09:19:12.84: [13816]: DIAL 5551616
 > Oct 16 09:19:12.84: [13816]: <-- [12:ATDT5551616\r]
 > Oct 16 09:19:22.08: [13816]: --> [4:+FCO]
 > Oct 16 09:19:24.54: [13816]: --> [15:+FNF:+FCI:"   ]
 > Oct 16 09:19:24.54: [13816]: REMOTE NSF "+FCI:""
 > Oct 16 09:19:24.54: [13816]: --> [32:      5105551616"+FIS:1,5,0,2,1]
 > Oct 16 09:19:24.54: [13816]: --> [43:0,0,3;<~[<Y\=|i]
 > Oct 16 09:19:24.65: [13816]: --> [57:@)eQ+v@hmBzdBeB0F`kG{@&]
 > Oct 16 09:19:25.33: [13816]: --> [18:K]
 > Oct 16 09:19:25.33: [13816]: --> [58::1,5,0,2,1,0,0,3;<~[<Y\=|i8m]
 > Oct 16 09:19:25.48: [13816]: --> [25:A"# A}]
 > Oct 16 09:19:25.95: [13816]: --> [33:tC'lAfqQK@A9]
 > Oct 16 09:19:26.67: [13816]: --> [2:]
 > Oct 16 09:19:26.67: [13816]: --> [33:@iWQFOiC?g5v^]
 > Oct 16 09:19:27.18: [13816]: --> [23: T.s024]
 > Oct 16 09:19:27.18: [13816]: --> [2:OK]
 > Oct 16 09:19:27.18: [13816]: REMOTE HANGUP: Unspecified Transmit Phase B error (code 20)
 > Oct 16 09:19:27.18: [13816]: SEND FAILED: Unspecified Transmit Phase B error
 > Oct 16 09:19:27.18: [13816]: SEND FAILED: Unspecified Transmit Phase B error; too many attempts to send
 > Oct 16 09:19:27.18: [13816]: <-- [5:ATH0\r]
 > Oct 16 09:19:27.41: [13816]: --> [2:OK]
 > Oct 16 09:19:27.43: [13816]: SESSION END
 > 
 >     ---- Unsent job status ----
 > 
 >    Destination: 5551616
 >          JobID: 2
 >        GroupID: 2
 >         Sender: John Hazard
 >       Mailaddr: hazard@hazard
 >         CommID: 00000007
 > Submitted From: localhost
 >     Page Width: 215 (mm)
 >    Page Length: 279 (mm)
 >     Resolution: 98 (lpi)
 >         Status: Unspecified Transmit Phase B error; too many attempts to send
 >        Dialogs: 3 (exchanges with remote device)
 >          Dials: 0 (consecutive failed calls to destination)
 >          Calls: 3 (total phone calls placed)
 >          Pages: 0 (pages transmitted)
 >       TotPages: 1 (total pages to transmit)
 >       Attempts: 0 (attempts to send current page)
 >         Dirnum: 0 (directory of next page to send)
 > 
 >     ---- Documents submitted for transmission ----
 > 
 > The following documents were submitted for transmission and are
 > available on the server for reuse until they are automatically
 > purged when this job is removed.  Documents may also be manually
 > removed using the faxrm command; consult faxrm(1) for information.
 > 
 > Filename                 Size Type
 > docq/doc2.cover         12519 PostScript cover page
 > docq/doc3.ps             5752 PostScript
 > 
 > 
 > # Configuration for using the Class 2.0 command interface
 > # with a USR v.34 Courier or Sporster modem.
 > #
 > # RTS/CTS flow control is used default.
 > #
 > #
 > CountryCode:		1
 > AreaCode:		510
 > FAXNumber:		1-510-555-6239
 > LongDistancePrefix:	1
 > InternationalPrefix:	011
 > DialStringRules:	"etc/dialrules"
 > ServerTracing:		1
 > SessionTracing:		11
 > RecvFileMode:		0666
 > LogFileMode:		0666
 > DeviceMode:		0660
 > RingsBeforeAnswer:	1
 > SpeakerVolume:		medium
 > GettyArgs:		"std.%s"
 > LocalIdentifier:	Hazard
 > TagLineFont:		etc/lutRS18.pcf
 > TagLineFormat:		"From %%l|%c|Page %%p of %%t"
 > MaxRecvPages:		25
 > #
 > #
 > # Modem-related stuff: should reflect modem command interface
 > # and hardware connection/cabling (e.g. flow control).
 > #
 > ModemType:		Class2.0	# use class 2.0 interface
 > ModemRate:		38400		# DCE-DTE communication rate
 > ModemFlowControl:	rtscts		# XON/XOFF flow control assumed
 > #
 > ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no flow control
 > ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for hardware flow control
 > ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for software flow control
 > #
 > ModemSetupDTRCmd:	ATS13=1&D2	# setup so DTR drop resets modem
 > ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
 > ModemResultCodesCmd:	ATQ0X4		# enable extended result codes
 > #
 > # NB: adaptive answer only seems to work properly when
 > #     the modem is left idling in Class 2.0
 > #
 > ModemSetupAACmd:	AT+FAA=1
 > #
 > # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
 > # Note that we both turn the speaker on/off and set volume.
 > #
 > ModemSetVolumeCmd:	"ATM0 ATM1 ATM1 ATM1 ATM2"
 > #
 > # Modem does not support HDLC frame tracing; we add this just
 > # to eliminate spurious ERROR results that confuse the naive.
 > #
 > Class2BUGCmd:		AT+FBU=0
 > #
 > # The modem doesn't support copy quality checking, even though it
 > # returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
 > # response so that the server will do copy quality checking.
 > #
 > Class2CQQueryCmd:	!(0),(0)	# override modem response



Home
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services