Unspecified Transmit Phase D error...

To: "HylaFAX-Mailingliste (E-Mail)" <flexfax@sgi.com>
Subject: Unspecified Transmit Phase D error...
From: Alexandre Meissonnier <ameissonnier@dohle.com>
Date: Wed, 16 Jul 1997 12:06:23 +0200

Hi there!

>From time to time I get "Unspecified Transmit Phase D errors" while sending 
faxes. After one
or two  pages have been transmitted normally, the connection is interrupted 
after HylaFAX has
sent the MPS (More Pages Same Document) signal. Following attempts to send 
the same job
sometimes succeed, somtimes they fail again with the same error message. In 
the latter case,
the receiving machine gets 3 times the first two pages of the fax but never 
sees the rest of it.

First, I thought that this error was caused by bad phone lines, since it 
occurred mostly when
sending faxes from Germany to Poland.But it also happens on calls inside 
Germany, and faxes
to the same destinations using a paper fax machine work without problems.

Now I'd like to know:
- What does this message mean? and
- What can I do about it?

My modem is a ZyXEL 1496E.

Here's a sample logfile of such a job:

------------------------------------------------
Jul 10 16:47:21.60: [ 5413]: SESSION BEGIN 00000849 xxxxxxxx
Jul 10 16:47:21.60: [ 5413]: SEND FAX: JOB 270 DEST xxxxxxx COMMID 00000849
Jul 10 16:47:21.85: [ 5413]: DELAY 2600 ms
Jul 10 16:47:24.58: [ 5413]: <-- 
[44:AT&B1&N0&S0*F0S18=2S38.3=1S39=0E0V1Q0S0=0H0\r]
Jul 10 16:47:24.81: [ 5413]: --> [2:OK]
Jul 10 16:47:24.81: [ 5413]: <-- [21:ATS8=2S7=60&H3&D2&C1\r]
Jul 10 16:47:24.84: [ 5413]: --> [2:OK]
Jul 10 16:47:24.84: [ 5413]: <-- [12:AT+FCLASS=2\r]
Jul 10 16:47:24.86: [ 5413]: --> [2:OK]
Jul 10 16:47:24.86: [ 5413]: <-- [10:AT+FTBC=0\r]
Jul 10 16:47:24.88: [ 5413]: --> [2:OK]
Jul 10 16:47:24.88: [ 5413]: <-- [10:AT+FBOR=0\r]
Jul 10 16:47:24.90: [ 5413]: --> [2:OK]
Jul 10 16:47:24.90: [ 5413]: <-- [13:AT+FPHCTO=30\r]
Jul 10 16:47:24.92: [ 5413]: --> [5:ERROR]
Jul 10 16:47:24.92: [ 5413]: MODEM Command error
Jul 10 16:47:24.92: [ 5413]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Jul 10 16:47:24.95: [ 5413]: --> [2:OK]
Jul 10 16:47:24.95: [ 5413]: <-- [7:ATM1L5\r]
Jul 10 16:47:24.97: [ 5413]: --> [2:OK]
Jul 10 16:47:24.97: [ 5413]: <-- [12:AT+FCLASS=2\r]
Jul 10 16:47:25.08: [ 5413]: --> [2:OK]
Jul 10 16:47:25.08: [ 5413]: <-- [10:AT+FTBC=0\r]
Jul 10 16:47:25.19: [ 5413]: --> [2:OK]
Jul 10 16:47:25.19: [ 5413]: <-- [10:AT+FBOR=0\r]
Jul 10 16:47:25.30: [ 5413]: --> [2:OK]
Jul 10 16:47:25.30: [ 5413]: <-- [13:AT+FPHCTO=30\r]
Jul 10 16:47:25.41: [ 5413]: --> [5:ERROR]
Jul 10 16:47:25.41: [ 5413]: MODEM Command error
Jul 10 16:47:25.41: [ 5413]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
Jul 10 16:47:25.53: [ 5413]: --> [2:OK]
Jul 10 16:47:25.53: [ 5413]: <-- [30:AT+FLID="Dohle Handelsgruppe"\r]
Jul 10 16:47:25.65: [ 5413]: --> [2:OK]
Jul 10 16:47:25.65: [ 5413]: DIAL 0,xxxxxxxxx
Jul 10 16:47:25.65: [ 5413]: <-- [18:ATX3DT0,xxxxxxx\r]
Jul 10 16:48:24.34: [ 5413]: --> [5:+FCON]
Jul 10 16:48:24.34: [ 5413]: --> [18:+FNSF:00 00 00 00 ]
Jul 10 16:48:24.34: [ 5413]: REMOTE NSF "00 00 00 00"
Jul 10 16:48:24.34: [ 5413]: --> [27:+FCSI:         +xxxxxxxxxxxxx ]
Jul 10 16:48:24.34: [ 5413]: REMOTE CSI "+xxxxxxxxxxxxx"
Jul 10 16:48:24.34: [ 5413]: --> [21:+FDIS:1,3,0,2,1,0,0,4]
Jul 10 16:48:24.34: [ 5413]: --> [2:OK]
Jul 10 16:48:24.34: [ 5413]: REMOTE best rate 9600 bit/s
Jul 10 16:48:24.34: [ 5413]: REMOTE max page width 1728 pixels in 215 mm
Jul 10 16:48:24.34: [ 5413]: REMOTE max unlimited page length
Jul 10 16:48:24.34: [ 5413]: REMOTE best vres 7.7 line/mm
Jul 10 16:48:24.34: [ 5413]: REMOTE best format 2-D MR
Jul 10 16:48:24.34: [ 5413]: REMOTE best 20 ms, 10 ms/scanline
Jul 10 16:48:24.34: [ 5413]: USE 9600 bit/s
Jul 10 16:48:24.34: [ 5413]: USE 20 ms, 10 ms/scanline
Jul 10 16:48:24.34: [ 5413]: SEND file "docq/doc265.ps;01"
Jul 10 16:48:24.34: [ 5413]: USE page width 1728 pixels in 215 mm
Jul 10 16:48:24.34: [ 5413]: USE unlimited page length
Jul 10 16:48:24.34: [ 5413]: USE 7.7 line/mm
Jul 10 16:48:24.34: [ 5413]: USE 1-D MR
Jul 10 16:48:24.34: [ 5413]: <-- [24:AT+FDIS=1,3,0,2,0,0,0,4\r]
Jul 10 16:48:24.46: [ 5413]: --> [2:OK]
Jul 10 16:48:24.46: [ 5413]: <-- [7:AT+FDT\r]
Jul 10 16:48:24.46: [ 5413]: --> [2:OK]
Jul 10 16:48:30.25: [ 5413]: --> [21:+FDCS:1,3,0,2,0,0,0,4]
Jul 10 16:48:30.25: [ 5413]: --> [7:CONNECT]
Jul 10 16:48:30.25: [ 5413]: SEND wait for XON
Jul 10 16:48:30.25: [ 5413]: --> [1:]
Jul 10 16:48:30.25: [ 5413]: SEND begin page
Jul 10 16:48:30.25: [ 5413]: <-- data [1025]
[--- more data ---]
Jul 10 16:49:06.43: [ 5413]: SENT 23298 bytes of data
Jul 10 16:49:06.43: [ 5413]: <-- data [2]
Jul 10 16:49:06.43: [ 5413]: SEND end page
Jul 10 16:49:11.07: [ 5413]: --> 
[56:]
Jul 10 16:49:11.07: [ 5413]: --> [2:OK]
Jul 10 16:49:11.07: [ 5413]: SEND send MPS (more pages, same document)
Jul 10 16:49:11.07: [ 5413]: <-- [9:AT+FET=0\r]
Jul 10 16:49:14.09: [ 5413]: --> [7:+FPTS:1]
Jul 10 16:49:14.09: [ 5413]: --> [2:OK]
Jul 10 16:49:14.09: [ 5413]: SEND recv MCF (message confirmation)
Jul 10 16:49:14.09: [ 5413]: SEND FAX (00000849): FROM xxxxxxx TO 
xxxxxxxxxx (page 1 of 3 sent in 0:50)
Jul 10 16:49:14.09: [ 5413]: USE page width 1728 pixels in 215 mm
Jul 10 16:49:14.09: [ 5413]: USE unlimited page length
Jul 10 16:49:14.09: [ 5413]: USE 7.7 line/mm
Jul 10 16:49:14.09: [ 5413]: USE 1-D MR
Jul 10 16:49:14.09: [ 5413]: <-- [7:AT+FDT\r]
Jul 10 16:49:14.20: [ 5413]: --> [7:CONNECT]
Jul 10 16:49:14.20: [ 5413]: SEND wait for XON
Jul 10 16:49:14.20: [ 5413]: --> [1:]
Jul 10 16:49:14.20: [ 5413]: SEND begin page
Jul 10 16:49:14.20: [ 5413]: <-- data [1024]
[--- more data ---]
Jul 10 16:49:49.75: [ 5413]: SENT 30382 bytes of data
Jul 10 16:49:49.75: [ 5413]: <-- data [2]
Jul 10 16:49:49.75: [ 5413]: SEND end page
Jul 10 16:49:54.45: [ 5413]: --> 
[51:]
Jul 10 16:49:54.45: [ 5413]: --> [2:OK]
Jul 10 16:49:54.45: [ 5413]: SEND send MPS (more pages, same document)
Jul 10 16:49:54.45: [ 5413]: <-- [9:AT+FET=0\r]
Jul 10 16:50:00.31: [ 5413]: --> [10:NO CARRIER]
Jul 10 16:50:00.31: [ 5413]: REMOTE HANGUP: Unspecified Transmit Phase D 
error, including +FPHCTO timeout between data and +FET command (code 50)
Jul 10 16:50:00.31: [ 5413]: <-- [6:AT+FK\r]
Jul 10 16:50:00.31: [ 5413]: --> [2:OK]
Jul 10 16:50:00.31: [ 5413]: SEND FAILED: Unspecified Transmit Phase D 
error, including +FPHCTO timeout between data and +FET command; too many 
attempts to send
Jul 10 16:50:00.31: [ 5413]: <-- [5:ATH0\r]
Jul 10 16:50:00.42: [ 5413]: --> [2:OK]
Jul 10 16:50:00.79: [ 5413]: SESSION END

--
Alexandre Meissonnier
Dohle Handelsgruppe Systemberatung GmbH
53719 Siegburg (Germany)
ameissonnier@dohle.com

Prev by Date: Re: HylaFAX and further development
Next by Date: hylafax-v4.0pl1: "Yes" in modem config doesn't work
Prev by thread: FaxMail Problem?
Next by thread: Re: Unspecified Transmit Phase D error...
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services