Problems setting up USRobotics SportserFlash Modem

[Juergen Vigna <jug@sad.it>]

Hi,

I use hylafax since version 3 and upgraded to version hylafax-v4.0pl1.
Now I use a TELEBIT-WorldBlazer Modem without problems on version v3.0pl1
and probably I could use it also on the new version without problems.

But, ... as I bought a new USRobotics SportserFlash Modem and wanted to
use that too for sending and receiving faxes I tried to set it up.

Installed hylafax-v4.0pl1 on a Linux-2.0.29 Pentium 133 PC and attached
the Modem to /dev/cua1 (ttyS1). I already configured successfully ppp
and uucp so the modem is tested and works correctly.

I launched faxsetup and faxaddmodem. Configured the modem as "usr-2.0"
and till here is all OK now comes the problem. I tried to send a FAX
(I did not yet activate the receiving -> getty) and this is the Server
log I received:

Jun  4 15:11:43 wsjug FaxQueuer[2184]: HylaFAX (tm) Version 4.0pl1
Jun  4 15:11:43 wsjug FaxQueuer[2184]: Copyright (c) 1990-1996 Sam Leffler
Jun  4 15:11:43 wsjug FaxQueuer[2184]: Copyright (c) 1991-1996 Silicon Graphic!
Jun  4 15:11:43 wsjug HylaFAX[2186]: HylaFAX INET Protocol Server: restarted.
Jun  4 15:11:43 wsjug HylaFAX[2186]: HylaFAX Old Protocol Server: restarted.
Jun  4 15:11:43 wsjug HylaFAX[2186]: HylaFAX SNPP Protocol Server: restarted.
Jun  4 15:11:45 wsjug FaxSend[2206]: servertracing = 0xffffffff (line 42)
Jun  4 15:11:45 wsjug FaxSend[2206]: sessiontracing = 0xffffffff (line 43)
Jun  4 15:11:45 wsjug FaxSend[2206]: recvfilemode = 0600 (line 44)
Jun  4 15:11:45 wsjug FaxSend[2206]: logfilemode = 0600 (line 45)
Jun  4 15:11:45 wsjug FaxSend[2206]: devicemode = 0666 (line 46)
Jun  4 15:11:45 wsjug FaxSend[2206]: Unknown configuration parameter "ringsbef!
Jun  4 15:11:45 wsjug FaxSend[2206]: speakervolume = off (line 48)
Jun  4 15:11:45 wsjug FaxSend[2206]: Unknown configuration parameter "gettyarg!
Jun  4 15:11:45 wsjug FaxSend[2206]: localidentifier = NothingSetup (line 50)
Jun  4 15:11:45 wsjug FaxSend[2206]: taglinefont = etc/lutRS18.pcf (line 51)
Jun  4 15:11:45 wsjug FaxSend[2206]: taglineformat = From %%l|%c|Page %%p of %!
Jun  4 15:11:45 wsjug FaxSend[2206]: qualifytsi = etc/tsi (line 53)
Jun  4 15:11:45 wsjug FaxSend[2206]: maxrecvpages = 25 (line 54)
Jun  4 15:11:45 wsjug FaxSend[2206]: modemtype = Class2.0 (line 60)
Jun  4 15:11:45 wsjug FaxSend[2206]: modemrate = 38400 (line 61)
Jun  4 15:11:45 wsjug FaxSend[2206]: modemflowcontrol = rtscts (line 62)
Jun  4 15:11:45 wsjug FaxSend[2206]: modemnoflowcmd = AT&H0&I0&R1 (line 64)
Jun  4 15:11:45 wsjug FaxSend[2206]: modemhardflowcmd = AT&H1&I0&R2 (line 65)
Jun  4 15:11:45 wsjug FaxSend[2206]: modemsoftflowcmd = AT&H2&I2&R1 (line 66)
Jun  4 15:11:45 wsjug FaxSend[2206]: modemsetupdtrcmd = ATS13=1&D2 (line 68)
Jun  4 15:11:45 wsjug FaxSend[2206]: modemsetupdcdcmd = AT&C1 (line 69)
Jun  4 15:11:45 wsjug FaxSend[2206]: modemresultcodescmd = ATQ0X4 (line 70)
Jun  4 15:11:45 wsjug FaxSend[2206]: modemsetupaacmd = AT+FAA=1 (line 75)
Jun  4 15:11:46 wsjug FaxSend[2206]: modemsetvolumecmd = ATM0 ATM1 ATM1 ATM1 A!
Jun  4 15:11:46 wsjug FaxSend[2206]: class2bugcmd = AT+FBU=0 (line 85)
Jun  4 15:11:46 wsjug FaxSend[2206]: class2cqquerycmd = !(0),(0) (line 91)
Jun  4 15:11:46 wsjug FaxSend[2206]: Define AreaCode = "471"
Jun  4 15:11:46 wsjug FaxSend[2206]: Define CountryCode = "39"
Jun  4 15:11:46 wsjug FaxSend[2206]: Define LongDistancePrefix = "0"
Jun  4 15:11:46 wsjug FaxSend[2206]: Define InternationalPrefix = "00"
Jun  4 15:11:46 wsjug FaxSend[2206]: Define Area = "471"
Jun  4 15:11:46 wsjug FaxSend[2206]: Define Country = "39"
Jun  4 15:11:46 wsjug FaxSend[2206]: Define IDPrefix = "00"
Jun  4 15:11:46 wsjug FaxSend[2206]: Define LDPrefix = "0"
Jun  4 15:11:46 wsjug FaxSend[2206]: Define WS = " ^I"
Jun  4 15:11:46 wsjug FaxSend[2206]: CanonicalNumber := [
Jun  4 15:11:46 wsjug FaxSend[2206]:   "#.*" = ""
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[abcABC]" = "2"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[defDEF]" = "3"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[ghiGHI]" = "4"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[jklJKL]" = "5"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[mnoMNO]" = "6"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[prsPRS]" = "7"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[tuvTUV]" = "8"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[wxyWXY]" = "9"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[^+0-9]+" = ""
Jun  4 15:11:46 wsjug FaxSend[2206]:   "^00" = "+"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "^0" = "+39"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "^[^+]" = "+39471&"
Jun  4 15:11:46 wsjug FaxSend[2206]: ]
Jun  4 15:11:46 wsjug FaxSend[2206]: DialString := [
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[- ^I.]+" = ""
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[abcABC]" = "2"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[defDEF]" = "3"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[ghiGHI]" = "4"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[jklJKL]" = "5"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[mnoMNO]" = "6"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[prsPRS]" = "7"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[tuvTUV]" = "8"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "[wxyWXY]" = "9"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "^0039471" = ""
Jun  4 15:11:46 wsjug FaxSend[2206]:   "^0471" = ""
Jun  4 15:11:46 wsjug FaxSend[2206]:   "^0039" = "0"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "^[+]39471" = ""
Jun  4 15:11:46 wsjug FaxSend[2206]:   "^[+]39" = "0"
Jun  4 15:11:46 wsjug FaxSend[2206]:   "^[+]" = "00"
Jun  4 15:11:46 wsjug FaxSend[2206]: ]
Jun  4 15:11:46 wsjug FaxSend[2206]: MODEM set DTR OFF
Jun  4 15:11:46 wsjug FaxSend[2206]: DELAY 2600 ms
Jun  4 15:11:49 wsjug FaxSend[2206]: MODEM set DTR ON
Jun  4 15:11:49 wsjug FaxSend[2206]: MODEM set baud rate: 38400 baud, input fl!
Jun  4 15:11:49 wsjug FaxSend[2206]: MODEM flush i/o
Jun  4 15:11:49 wsjug FaxSend[2206]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Jun  4 15:11:54 wsjug FaxSend[2206]: MODEM TIMEOUT: reading line from modem
Jun  4 15:11:54 wsjug FaxSend[2206]: MODEM <Timeout>
Jun  4 15:11:54 wsjug FaxSend[2206]: MODEM set DTR OFF
Jun  4 15:11:54 wsjug FaxSend[2206]: DELAY 2600 ms
Jun  4 15:11:56 wsjug FaxSend[2206]: MODEM set DTR ON
Jun  4 15:11:56 wsjug FaxSend[2206]: MODEM set baud rate: 38400 baud, input fl!
Jun  4 15:11:56 wsjug FaxSend[2206]: MODEM flush i/o
Jun  4 15:11:56 wsjug FaxSend[2206]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Jun  4 15:12:01 wsjug FaxSend[2206]: MODEM TIMEOUT: reading line from modem
Jun  4 15:12:01 wsjug FaxSend[2206]: MODEM <Timeout>
Jun  4 15:12:01 wsjug FaxSend[2206]: MODEM set DTR OFF
Jun  4 15:12:01 wsjug FaxSend[2206]: /dev/ttyS1: Can not initialize modem.
Jun  4 15:12:01 wsjug FaxSend[2206]: STATE CHANGE: BASE -> MODEMWAIT (timeout !
Jun  4 15:12:31 wsjug FaxSend[2206]: MODEM set DTR OFF
Jun  4 15:12:31 wsjug FaxSend[2206]: DELAY 2600 ms
Jun  4 15:12:34 wsjug FaxSend[2206]: MODEM set DTR ON
Jun  4 15:12:34 wsjug FaxSend[2206]: MODEM set baud rate: 38400 baud, input fl!
Jun  4 15:12:34 wsjug FaxSend[2206]: MODEM flush i/o
Jun  4 15:12:34 wsjug FaxSend[2206]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Jun  4 15:12:39 wsjug FaxSend[2206]: MODEM TIMEOUT: reading line from modem
Jun  4 15:12:39 wsjug FaxSend[2206]: MODEM <Timeout>
Jun  4 15:12:39 wsjug FaxSend[2206]: MODEM set DTR OFF
Jun  4 15:12:39 wsjug FaxSend[2206]: DELAY 2600 ms
Jun  4 15:12:41 wsjug FaxSend[2206]: MODEM set DTR ON
Jun  4 15:12:41 wsjug FaxSend[2206]: MODEM set baud rate: 38400 baud, input fl!
Jun  4 15:12:41 wsjug FaxSend[2206]: MODEM flush i/o
Jun  4 15:12:41 wsjug FaxSend[2206]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Jun  4 15:12:46 wsjug FaxSend[2206]: MODEM TIMEOUT: reading line from modem
Jun  4 15:12:46 wsjug FaxSend[2206]: MODEM <Timeout>
Jun  4 15:12:46 wsjug FaxSend[2206]: MODEM set DTR OFF

You will see that there is a problem in reading a response line from
the Modem. I made a "cu" to the modem-port and tried to insert the command
by hand (ATE0V1Q0X4S0=0H0) and the answer was "OK". So I really don't know
how to proceed, maybe one of you had a similar problem and could tell me
how to get out of this mess.

I'm not subscribed to the mailing-list so please CC the answer to my
personal EMail-Address.

With many thanks

Juergen

---------------------------------------------------------------------
Dr. Juergen Vigna                     E-Mail: jug@sad.it
Gerbergasse 60                        Tel:    +39-471-450260
I-39100 Bozen                         Fax:    +39-471-970042
ITALY

"Why be a man when you can be a success?"
                -- Bertold Brecht

---------------------------------------------------------------------