Re: error codes

[Matthias.Apitz@SOFTCON.de (Matthias Apitz)]

Dror BenShlomo wrote:
    
    My system: HylaFAX Version 3.0p10113
    	   indy - IRIX 5.3
    	   baca modem MV.34EM (14,400)

You should update to v4.0pl1;
    
    I'm using it without any problems most of the time (or more accurate
    to say, most of the fax machines I send to).
    
    1) How can I get a error code that dont match the error message as 
       written in the FAQ (Q64).

    2) I got garbage in the log file as U can see 

I can't see any garbage in the trace;

	matthias
    
    Jan 28 15:54:09.47: [ 6313]: SESSION BEGIN
    Jan 28 15:54:09.47: [ 6313]: DELAY 2600 ms
    Jan 28 15:54:12.07: [ 6313]: <-- [14:ATE0V1Q0S0=0H0]
    Jan 28 15:54:12.33: [ 6313]: --> [2:OK]
    Jan 28 15:54:12.33: [ 6313]: <-- [20:ATS8=2S7=60&K4&D3&C1]
    Jan 28 15:54:12.59: [ 6313]: --> [2:OK]
    Jan 28 15:54:12.59: [ 6313]: <-- [11:AT+FCLASS=2]
    Jan 28 15:54:12.85: [ 6313]: --> [2:OK]
    Jan 28 15:54:12.85: [ 6313]: <-- [9:AT+FTBC=0]
    Jan 28 15:54:13.11: [ 6313]: --> [2:OK]
    Jan 28 15:54:13.11: [ 6313]: <-- [9:AT+FBOR=0]
    Jan 28 15:54:13.37: [ 6313]: --> [2:OK]
    Jan 28 15:54:13.37: [ 6313]: <-- [13:AT+FPHCTO=600]
    Jan 28 15:54:13.63: [ 6313]: --> [2:OK]
    Jan 28 15:54:13.63: [ 6313]: <-- [23:AT+FDCC=1,5,2,2,1,0,0,0]
    Jan 28 15:54:13.89: [ 6313]: --> [2:OK]
    Jan 28 15:54:13.89: [ 6313]: <-- [4:ATM0]
    Jan 28 15:54:14.15: [ 6313]: --> [2:OK]
    Jan 28 15:54:14.15: [ 6313]: <-- [11:AT+FCLASS=2]
    Jan 28 15:54:14.41: [ 6313]: --> [2:OK]
    Jan 28 15:54:14.41: [ 6313]: <-- [9:AT+FTBC=0]
    Jan 28 15:54:14.67: [ 6313]: --> [2:OK]
    Jan 28 15:54:14.67: [ 6313]: <-- [9:AT+FBOR=0]
    Jan 28 15:54:14.93: [ 6313]: --> [2:OK]
    Jan 28 15:54:14.93: [ 6313]: <-- [13:AT+FPHCTO=600]
    Jan 28 15:54:15.19: [ 6313]: --> [2:OK]
    Jan 28 15:54:15.19: [ 6313]: <-- [23:AT+FDCC=1,5,2,2,1,0,0,0]
    Jan 28 15:54:15.45: [ 6313]: --> [2:OK]
    Jan 28 15:54:15.45: [ 6313]: <-- [20:AT+FLID="+036190992"]
    Jan 28 15:54:15.71: [ 6313]: --> [2:OK]
    Jan 28 15:54:15.71: [ 6313]: DIAL 5659692
    Jan 28 15:54:15.71: [ 6313]: <-- [11:ATDT5659692]
    Jan 28 15:54:30.46: [ 6313]: --> [5:+FCON]
    Jan 28 15:54:33.28: [ 6313]: --> [29:+FCSI: "       972 3 5659692"]
    Jan 28 15:54:33.28: [ 6313]: REMOTE CSI "972 3 5659692"
    Jan 28 15:54:33.62: [ 6313]: --> [22:+FDIS: 1,3,0,2,1,0,0,4]
    Jan 28 15:54:33.73: [ 6313]: --> [2:OK]
    Jan 28 15:54:33.73: [ 6313]: REMOTE best rate 9600 bit/s
    Jan 28 15:54:33.74: [ 6313]: REMOTE max page width 1728 pixels in 215 mm
    Jan 28 15:54:33.74: [ 6313]: REMOTE max unlimited page length 
    Jan 28 15:54:33.74: [ 6313]: REMOTE best vres 7.7 line/mm
    Jan 28 15:54:33.74: [ 6313]: REMOTE best format 2-D MR
    Jan 28 15:54:33.74: [ 6313]: REMOTE best 20 ms, 10 ms/scanline
    Jan 28 15:54:33.74: [ 6313]: REMOTE does not support PostScript transfer
    Jan 28 15:54:33.74: [ 6313]: USE 9600 bit/s
    Jan 28 15:54:33.74: [ 6313]: USE 20 ms, 10 ms/scanline
    Jan 28 15:54:33.74: [ 6313]: SEND file "docq/doc28347.6483"
    Jan 28 15:54:33.83: [ 6313]: USE page width 1728 pixels in 215 mm
    Jan 28 15:54:33.83: [ 6313]: USE unlimited page length 
    Jan 28 15:54:33.83: [ 6313]: USE 7.7 line/mm
    Jan 28 15:54:33.84: [ 6313]: USE 1-D MR
    Jan 28 15:54:33.84: [ 6313]: <-- [23:AT+FDIS=1,3,0,2,0,0,0,4]
    Jan 28 15:54:34.09: [ 6313]: --> [2:OK]
    Jan 28 15:54:34.10: [ 6313]: <-- [6:AT+FDT]
    Jan 28 15:54:41.25: [ 6313]: --> [22:+FDCS: 1,3,0,2,0,0,0,3]
    Jan 28 15:54:41.47: [ 6313]: --> [7:CONNECT]
    Jan 28 15:54:41.47: [ 6313]: SEND wait for XON
    Jan 28 15:54:41.47: [ 6313]: --> [1:^Q]
    Jan 28 15:54:41.47: [ 6313]: SEND begin page
    Jan 28 15:54:41.51: [ 6313]: <-- data [1030]
    Jan 28 15:55:37.46: [ 6313]: <-- data [1024]