Hylafax Mailing List Archives

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] But when I sendfax some .tfi ,then the result is "555 /tmp/doc2.ps Operation not permitted "



I use busybox 1.1.1 and modify it , then it's OK.status is "Running and Idle".
But when I sendfax some .tfi ,then the result is "555 /tmp/doc2.ps Operation not permitted "
I use uucp user for faxuser and run in root session.there is some problem?
I can't see any information about /var/log/message, maybe I will try to set ServerTracing.
There is anyone to help me? Thanks.

Good luck,

gongfen

2006/5/10, Fred Newtz <fnewtz@xxxxxxxxxx>:
Have you turned your logging level up higher and checked your system log?  That told me right away what specific command I was sending the modem that was causing an error and not allowing Hylafax to initialize the modem.
 
I edited my config.ttyS0 file (will be different depending on your serial port) and set ServerTracing: 0xFFF.  Then I checked in the /var/log/messages file and saw the detailed output from the modem.  I had set the ModemSetupDCDCommand improperly for my modem.  So I changed it to the correct value and everything was good.

Good luck,

Fred
 
----- Original Message -----
From: gongfen
Sent: Tuesday, May 09, 2006 7:38 PM
Subject: Re: [hylafax-users] Gentoo - Hylafax 4.2.5 - Waiting for modem to come ready

I got this problem too.faxstat result is Waiting for modem to come ready.
I read the FaxGettyApp.c++ code, and can't slove this problem.
Maybe I need more time to debug it.

There is anyone to help me ?

Thanks.

gongfen

2006/5/10, Fred Newtz <fnewtz@xxxxxxxxxx>:
Here is my results from probemodem:
 
ATI0    RESULT = "OK"   RESPONSE = "MT5656ZDX"
ATI1    RESULT = "OK"   RESPONSE = "042"
ATI2    RESULT = "OK"   RESPONSE = "OK"
ATI3    RESULT = "OK"   RESPONSE = "ACF3_V2.000B-V90_P21_FSH"
ATI4    RESULT = "OK"   RESPONSE = "a007040284C6002F"
ATI5    RESULT = "OK"   RESPONSE = "B5"
ATI6    RESULT = "OK"   RESPONSE = "RCV56DPF-PLL L8773A Rev 62.01/62.01"
ATI7    RESULT = "OK"   RESPONSE = "OK"
ATI8    RESULT = "ERROR"        RESPONSE = "ERROR"
ATI9    RESULT = "ERROR"        RESPONSE = "ERROR"
Of course all the class stuff shows up but I don't know how important it is to this problem.
 
I have the following in my /etc/inittab file:
m0:2345:respawn:/usr/local/sbin/faxgetty ttyS0
 
I have verifyed it is running with ps -aux.  When it first loads it does state Initializing Server then goes to Waiting for modem to come ready.
 
I have done a cat /dev/ttyS0 and I see the modem put up the ring when I call it.  I get the tones when I call by voice but when I call with a fax machine it will not answer.  Could it have anything to do with my :
 
ModemResetCmds:         ATZ
 
Should I set it to a more complex string that turns auto answer on, or does Hylafax turn it on for me?
 
Will it cause a problem to be doing cat /dev/ttyS0 when I am trying to send the fax?
 
Please let me know if I have not provided enough information to troubleshoot this problem.
 
Thanks,

Fred



--
Communication is not a problem, but a channce!
MAIl to: gongfen@xxxxxxxxx

Home
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services