|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Faxgetty cannot init modem, but probemodem works.
I disconnected the modem from the Digi baord and
plugged it directly into /dev/ttyS0 on the back of the
server (a HP ML350 G4) in an attempt to eliminate a
variable (the Digi Portserver). It faxgetty still
acts the same, it cannot init the modem. Probemodem
sees the modem just fine though..
Mucho Help! :-)
Thx
May 6 19:39:59 server2 FaxGetty[23311]: CAUGHT SIGNAL
15
May 6 19:39:59 server2 FaxGetty[23311]: CLOSE
/dev/ttyS0
May 6 19:39:59 server2 FaxGetty[23370]: OPEN
/dev/ttyS0 HylaFAX (tm) Version 4.2.5
May 6 19:39:59 server2 FaxGetty[23370]: /dev/ttyS0:
Can not lock device.
May 6 19:39:59 server2 hylafax: faxgetty shutdown
succeeded
May 6 19:40:29 server2 FaxGetty[23370]: Purge stale
UUCP lock /var/lock/LCK..ttyS0
May 6 19:41:37 server2 FaxGetty[23370]: /dev/ttyS0:
Can not initialize modem.
May 6 19:44:54 server2 FaxGetty[23370]: Unable to
setup modem on /dev/ttyS0; giving up after 2 attempts
May 6 19:44:54 server2 FaxGetty[23370]: CLOSE
/dev/ttyS0
May 6 19:44:54 server2 FaxQueuer[23359]: MODEM
/dev/ttyS0 appears to be wedged
May 6 19:44:54 server2 FaxQueuer[23359]: MODEM
WEDGED: bin/wedged "ttyS0" "/dev/ttyS0"
May 6 19:44:54 server2 FaxGetty[23847]: OPEN
/dev/ttyS0 HylaFAX (tm) Version 4.2.5
May 6 19:44:54 server2 FaxQueuer[23359]: NOTIFY exit
status: 0 (23846)
--- jeff leads <jleads@xxxxxxxxx> wrote:
> I have a USR Courier V.Everything attached to a Digi
> Portserver TS8, I'm running a new install of Redhat
> ES4 and Hylafax 4.2.5 (installed using RPM). I cant
> seem to figure out why faxgetty can't speak to the
> modem to initialize it. I set logging to 0xfff
> (output below). I have also tried differnt ports on
> the portserver with the same result. Probemodem
> works
> fine however (output below). I have attached my
> config.tty407 (output below).
>
> Can some one point me in the right direction?
>
> Thanks a bunch
>
> Jeff
>
>
> [root@server2 etc]# ls -la /dev/tty407
> crw-rw-rw- 1 uucp root 251, 7 May 6 15:01
> /dev/tty407
>
>
>
> [root@server2 ~]# probemodem tty407
> Now we are going to probe the tty port. This takes
> a
> few seconds,
> so be patient. Note that if you do not have the
> modem
> cabled to
> the port, or the modem is turned off, this may hang
> (just go and
> cable up the modem or turn it on, or whatever).
>
> Probing for best speed to talk to modem: 38400 OK.
>
> This looks like a Class 1 and 2.0 modem.
>
> ATI0 RESULT = "OK" RESPONSE = "5608A"
> ATI1 RESULT = "E77B" RESPONSE = "E77B"
> ATI2 RESULT = "OK" RESPONSE = "OK"
> ATI3 RESULT = "OK" RESPONSE = "USRobotics
> Courier
> V.Everything EXT"
> ATI4 RESULT = "OK" RESPONSE = "USRobotics
> Courier
> V.Everything Settings..."
> ATI5 RESULT = "OK" RESPONSE = "USRobotics
> Courier
> V.Everything NVRAM Settings..."
> ATI6 RESULT = "OK" RESPONSE = "USRobotics
> Courier
> V.Everything Link Diagnostics..."
> ATI7 RESULT = "OK" RESPONSE = "USRobotics
> Courier
> V.Everything Configuration Profile..."
> ATI8 RESULT = "ERROR" RESPONSE = "ERROR"
> ATI9 RESULT = "OK" RESPONSE =
> "(1.0USR00BA\MODEM\PNPC107\USRobotics Courier
> V.Everything EXT)"
>
>
>
>
> [root@server2 ~]#tail -f /var/log/messages
> May 6 15:30:53 server2 FaxGetty[31028]: OPEN
> /dev/tty407 HylaFAX (tm) Version 4.2.3
> May 6 15:30:53 server2 FaxGetty[31028]: Purge stale
> UUCP lock /var/lock/LCK..tty407
> May 6 15:30:54 server2 FaxGetty[31028]: MODEM set
> DTR
> OFF
> May 6 15:30:54 server2 FaxGetty[31028]: DELAY 75 ms
> May 6 15:30:55 server2 FaxGetty[31028]: MODEM set
> DTR
> ON
> May 6 15:30:55 server2 FaxGetty[31028]: DELAY 2600
> ms
> May 6 15:30:58 server2 FaxGetty[31028]: MODEM set
> baud rate: 38400 baud, input flow RTS/CTS, output
> flow
> RTS/CTS
> May 6 15:30:58 server2 FaxGetty[31028]: DELAY 10 ms
> May 6 15:30:58 server2 FaxGetty[31028]: MODEM flush
> i/o
> May 6 15:30:58 server2 FaxGetty[31028]: <--
> [4:ATZ\r]
> May 6 15:31:28 server2 FaxGetty[31028]: MODEM
> TIMEOUT: reading line from modem
> May 6 15:31:28 server2 FaxGetty[31028]: MODEM
> <Timeout>
> May 6 15:31:28 server2 FaxGetty[31028]: MODEM set
> DTR
> OFF
> May 6 15:31:28 server2 FaxGetty[31028]: DELAY 75 ms
> May 6 15:31:28 server2 FaxGetty[31028]: MODEM set
> DTR
> ON
> May 6 15:31:28 server2 FaxGetty[31028]: DELAY 2600
> ms
> May 6 15:31:47 server2 FaxGetty[31028]: MODEM set
> baud rate: 38400 baud, input flow RTS/CTS, output
> flow
> RTS/CTS
> May 6 15:31:47 server2 FaxGetty[31028]: DELAY 10 ms
> May 6 15:31:47 server2 FaxGetty[31028]: MODEM flush
> i/o
> May 6 15:31:47 server2 FaxGetty[31028]: <--
> [4:ATZ\r]
> May 6 15:32:17 server2 FaxGetty[31028]: MODEM
> TIMEOUT: reading line from modem
>
>
>
> [root@server2 ~]#cat
> /var/spool/hylafax/etc/config.tty407
>
> # Configuration for using the Class 2.0 command
> interface
> # with a USR v.34 Courier or Sporster modem.
> #
> # RTS/CTS flow control is used default.
> #
> #
> CountryCode: 1
> AreaCode: 859
> FAXNumber: +1.859.544.7475
> LongDistancePrefix: 1
> InternationalPrefix: 011
> DialStringRules: etc/dialrules
> ServerTracing: 0xFFF
> SessionTracing: 11
> RecvFileMode: 0644
> LogFileMode: 0644
> DeviceMode: 0666
> RingsBeforeAnswer: 1
> SpeakerVolume: off
> GettyArgs: "-h %l dx_%s"
> LocalIdentifier: "KRN Business FAX"
> TagLineFont: etc/lutRS18.pcf
> TagLineFormat: "From %%l|%c|Page %%P of
> %%T"
> MaxRecvPages: 25
> #
> #
> # Modem-related stuff: should reflect modem command
> interface
> # and hardware connection/cabling (e.g. flow
> control).
> #
> ModemType: Class2.0 # use class
> 2.0 interface
> ModemRate: 38400 # DCE-DTE
> communication rate
> ModemFlowControl: rtscts # XON/XOFF
> flow control assumed
> #
> ModemNoFlowCmd: AT&H0&I0&R1 # setup
> modem
> for no flow control
> ModemHardFlowCmd: AT&H1&I0&R2 # setup
> modem
> for hardware flow control
> ModemSoftFlowCmd: AT&H2&I2&R1 # setup
> modem
> for software flow control
> #
> ModemSetupDTRCmd: ATS13=1&D2 # setup so
> DTR
> drop resets modem
> ModemSetupDCDCmd: AT&C1 # setup so
> DCD
> reflects carrier (or not)
> ModemResultCodesCmd: ATQ0X4 # enable
> extended result codes
> #
> # NB: adaptive answer only seems to work properly
> when
> # the modem is left idling in Class 2.0
> #
> #ModemSetupAACmd: AT+FAA=1
> #
> # Set modem speaker volume commands: OFF QUIET LOW
> MEDIUM HIGH.
> # Note that we both turn the speaker on/off and set
> volume.
> #
> ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
> #
> # Modem does not support HDLC frame tracing; we add
> this just
> # to eliminate spurious ERROR results that confuse
> the
> naive.
> #
> Class2BUGCmd: AT+FBU=0
> #
> # The modem doesn't support copy quality checking,
> even though it
> # returns (0-2,0-2) for AT+FCQ=?; therefore we
>
=== message truncated ===
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
