When running: less /proc/pci ,I am unable to see something like this:
Bus 0, device 13, function 0:
Communication controller: Lucent Microelectronics Venus Modem
(V90, 56KFlex) (rev 0).
IRQ 9.
Master Capable. No bursts. Min Gnt=252.Max Lat=14.
Non-prefetchable 32 bit memory at 0xffadfe00 [0xffadfeff].
I/O at 0x7800 [0x78ff].
I/O at 0x7400 [0x74ff].
I/O at 0x7fe0 [0x7fe7].
LSPCI shows nothing related to the modem too.
I have also tried using kudzu and it is also not seeing this card.
The faxcard is Multi Tech MT5634ZPX-PCI-U. It was tested on another Linux Box and a Windows Box and was working,
The Linux distro is CentOS.
The Mother board is PCChips M861G v1.6a and it's specs are below:
The key features of this motherboard include:
Socket-754 Processor Support
• Supports AMD Athlon 64/Sempron processors
• Supports Front-Side Bus 800 MHz
Note: HyperTransport Technology is a point-to-point link between two
devices, it enables integrated circuits to exchange information at much
higher speeds than currently available interconnect technologies.
Chipset
There are VIA K8M800 Northbridge and VT8237 Southbridge in this chipset
in accordance with an innovative and scalable architecture with proven reliability
and performance.
• Defines Highly Integrated Solutions for High-Performance Workstation
& PC Desktop Designs -- High-performance North Bridge with
HyperTransport interface to AMD™ K8 CPU plus AGP 8X external
bus to external Graphics Controller plus high-speed V-Link interface to
South Bridge
2
Motherboard User's Guide
• High Performance HyperTransport CPU Interface -- Processor interface
via HyperTransport interface
• Full Featured Accelerated Graphics Port (AGP) Controller
− − AGP v3.0 compliant 8X / 4X transfer mode with Fast Write Support
− − Pipelined split-transaction long-burst transfers up to 2.1 GB/sec (4
bytes x 533 MHz)
• High Bandwidth 1 GB/Sec 16-Bit Ultra V-Link Host Controller --
Supports 66MHz, 4X and 8X transfer modes, Ultra V-Link Host
interface with total bandwidth of 1 GB/sec
• Advanced System Power Management Support -- ACPI 2.0 and PCI
Bus Power Management 1.2 compliant
• PCI to system memory data streaming up to 132Mbyte/sec (data sent to
north bridge via high speed Ultra V-Link interface)
• PCI-2.2 compliant, 32-bit 3.3V PCI interface with 5V tolerant inputs
• Support three PCI slots of arbitration and decoding for all integrated
functions and LPC bus.
• Dual Channel Serial ATA/RAID Controller—Complies with Serial ATA
Specification Revision 1.0
Memory Support
• Two 184-pin 2.5V DIMM sockets for DDR SDRAM memory modules
• Supports DDR400/333/266 memory bus
• Maximum installed memory is 2GB
Expansion Slots
• One CNR slot
• One 8X AGP slot
• Two 32-bit PCI slots for PCI 2.2-compliant bus interface
Onboard IDE channels
• Two IDE Connectors
• Supports PIO (Programmable Input/Output) and DMA (Direct Memory
Access) modes
• Supports IDE Ultra DMA bus mastering with transfer rates of 133/100/
66 MB/sec
Serial ATA
• Two Serial ATA Connectors
• Transfer rate exceeding best ATA (~150 MB/s) with scalability to higher
rates
• Low pin count for both host and devices
AC'97 Codec
• Compliant with AC'97 2.3 specification
• 16-bit Stereo full-duplex CODEC with independent and variable
sampling rate
3
Chapter 1: Introduction
• Support for 3.3v digital, 5v analog power supply and low power
consumption management
• Three analog line-level stereo inputs with 5-bit volume control:
LINE_IN, CD, AUX
• Front-Out, Surround-Out, MIC-In and LINE-In Jack Sensing
• Two analog line-level mono input
• Standard 48-Pin LQFP
Onboard I/O Ports
• Two PS/2 ports for mouse and keyboard
• One serial port
• One parallel port
• One VGA port
• Four back-panel USB2.0 ports
• One LAN port (optional)
• Audio jacks for microphone, line-in and line-out
Fast Ethernet LAN (optional)
• Built-in 100Base-TX/10Base-T Physical Layer solution
• Dual Speed – 100/10 Mbps
• MII Interface to Ethernet Controller and Configuration & Status
• Auto Negotiation: 10/100, Full/Half Duplex
• Meet All applicable IEEE 802.3, 10Base-T and 100 Base-TX Standards
USB 2.0
• Compliant with Universal Serial Bus Specification Revision 2.0
• Compliant with Intel's Enhanced Host Controller Interface Specification
Revision 1.0
• Compliant with Universal Host Controller Interface Specification
Revision 1.1
• PCI multi-function device consists of two UHCI Host Controller cores
for full-/low-speed signaling and one EHCI Host Controller core for
high-speed signaling
• Root hub consists 4 downstream facing ports with integrated physical
layer transceivers shared by UHCI and EHCI Host Controller, up to
eight functional ports
• Support PCI-Bus Power Management Interface Specification release 1.1
• Legacy support for all downstream facing ports
Is there anything wrong with this type of board ? Chipset ?
