Good morning... Hylafax is working perfectly, but
now we have recieved a PDF file which cannot be opened. Here's the log that we receive...... Does anybody know if the sender has recieved an OK
or an ERROR ???????? It won't be very good if the sender recieved an OK..
;(
Thanks in advance Koro ------------------------------ Could not open recvq/fax000001396.tif; either not
TIFF or corrupted.
ReceivedOn: ttyS0
The full document was not received because:
Failed to properly detect high-speed data carrier.
---- Transcript of session follows ----
Feb 20 20:18:26.43: [ 1061]: SESSION BEGIN 000002544 34943744153
Feb 20 20:18:26.43: [ 1061]: HylaFAX (tm) Version 4.2.1
Feb 20 20:18:26.43: [ 1061]: <-- [4:ATA\r]
Feb 20 20:18:32.51: [ 1061]: --> [7:CONNECT]
Feb 20 20:18:32.51: [ 1061]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Feb 20 20:18:32.51: [ 1061]: RECV FAX: begin
Feb 20 20:18:34.44: [ 1061]: --> [7:CONNECT]
Feb 20 20:18:35.27: [ 1061]: --> [7:CONNECT]
Feb 20 20:18:35.84: [ 1061]: --> [2:OK]
Feb 20 20:18:35.84: [ 1061]: <-- [9:AT+FRH=3\r]
Feb 20 20:18:36.73: [ 1061]: --> [7:CONNECT]
Feb 20 20:18:37.86: [ 1061]: --> [2:OK]
Feb 20 20:18:37.86: [ 1061]: REMOTE wants 14400 bit/s
Feb 20 20:18:37.86: [ 1061]: REMOTE wants A4 page width (215 mm)
Feb 20 20:18:37.86: [ 1061]: REMOTE wants unlimited page length
Feb 20 20:18:37.86: [ 1061]: REMOTE wants 7.7 line/mm
Feb 20 20:18:37.86: [ 1061]: REMOTE wants 2-D MMR
Feb 20 20:18:37.86: [ 1061]: REMOTE wants T.30 Annex A, 256-byte ECM
Feb 20 20:18:37.86: [ 1061]: RECV training at v.17 14400 bit/s
Feb 20 20:18:37.86: [ 1061]: <-- [11:AT+FRM=145\r]
Feb 20 20:18:39.57: [ 1061]: --> [7:CONNECT]
Feb 20 20:18:41.12: [ 1061]: RECV: TCF 2753 bytes, 0% non-zero, 2729 zero-run
Feb 20 20:18:41.12: [ 1061]: --> [10:NO CARRIER]
Feb 20 20:18:41.12: [ 1061]: DELAY 75 ms
Feb 20 20:18:41.20: [ 1061]: TRAINING succeeded
Feb 20 20:18:41.20: [ 1061]: <-- [9:AT+FTH=3\r]
Feb 20 20:18:41.26: [ 1061]: --> [7:CONNECT]
Feb 20 20:18:42.57: [ 1061]: --> [2:OK]
Feb 20 20:18:42.57: [ 1061]: <-- [11:AT+FRM=146\r]
Feb 20 20:18:43.66: [ 1061]: --> [7:CONNECT]
Feb 20 20:23:47.30: [ 1061]: HDLC frame not byte-oriented. Trailing
byte: 0xe0
Feb 20 20:23:47.30: [ 1061]: --> [10:NO CARRIER]
Feb 20 20:23:47.30: [ 1061]: <-- [9:AT+FRH=3\r]
Feb 20 20:23:47.66: [ 1061]: --> [7:CONNECT]
Feb 20 20:23:48.61: [ 1061]: --> [2:OK]
Feb 20 20:23:48.61: [ 1061]: RECV recv PPS (partial page signal)
Feb 20 20:23:48.61: [ 1061]: RECV recv EOP (no more pages or documents)
Feb 20 20:23:48.61: [ 1061]: RECV received 1 frames of block 1 of page
1
Feb 20 20:23:48.61: [ 1061]: <-- [9:AT+FRS=7\r]
Feb 20 20:23:48.74: [ 1061]: --> [2:OK]
Feb 20 20:23:48.74: [ 1061]: <-- [9:AT+FTH=3\r]
Feb 20 20:23:48.79: [ 1061]: --> [7:CONNECT]
Feb 20 20:23:51.12: [ 1061]: --> [2:OK]
Feb 20 20:23:51.12: [ 1061]: RECV send PPR (partial page request)
Feb 20 20:23:51.12: [ 1061]: <-- [11:AT+FRM=146\r]
Feb 20 20:23:52.00: [ 1061]: --> [8:+FCERROR]
Feb 20 20:23:52.00: [ 1061]: <-- [11:AT+FRM=146\r]
Feb 20 20:23:59.11: [ 1061]: --> [2:OK]
Feb 20 20:23:59.11: [ 1061]: <-- [9:AT+FRS=7\r]
Feb 20 20:23:59.24: [ 1061]: --> [2:OK]
Feb 20 20:23:59.25: [ 1061]: RECV FAX: Failed to properly detect high-speed
data carrier.
Feb 20 20:23:59.25: [ 1061]: <-- [9:AT+FTH=3\r]
Feb 20 20:23:59.25: [ 1061]: RECV FAX (000002544): from <UNSPECIFIED>,
page 1 in 5:18, INF, 7.7 line/mm, 2-D MMR, 14400 bit/s
Feb 20 20:23:59.26: [ 1061]: RECV FAX (000002544): recvq/fax000001396.tif
from <UNSPECIFIED>, route to <unspecified>, 1 pages in 5:27
Feb 20 20:23:59.30: [ 1061]: --> [7:CONNECT]
Feb 20 20:24:00.62: [ 1061]: --> [2:OK]
Feb 20 20:24:00.62: [ 1061]: RECV FAX (000002544): session with <UNSPECIFIED>
terminated abnormally: Failed to properly detect high-speed data carrier.
Feb 20 20:24:00.62: [ 1061]: RECV FAX: bin/faxrcvd "recvq/fax000001396.tif"
"ttyS0" "000002544" "Failed to properly detect
high-speed data carrier." "" ""
Feb 20 20:24:00.63: [ 1061]: RECV FAX: end
Feb 20 20:24:00.63: [ 1061]: SESSION END
