|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Problem to receive fax
Hi Luca.
Please try Class 1.
Regards
ANDREW RINALDI
Mainpine Support
USA +1 718 701 2422 | Asia/Europe +44 1225 436137
andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com
-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Pignedoli Luca
Sent: 10 February 2006 08:24
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] Problem to receive fax
Hi all.
I have install hyalfax server 4.2.5 on Debian 3.1 and i have connected a
modem:
"MODEM VENUS V.90 KFAV173 SERIAL "VERSION 1.04 / 14.07.2000" Venus V.90
kfav173 Serial "Version 1.04"
When i receive a fax the communication terminated whith this error:
An attempt to receive facsimile on ttyS0 failed because:
Unspecified Phase C error, including too much delay between TCF and +FDR
command
---- Transcript of session follows ----
Feb 10 14:57:43.19: [ 8557]: SESSION BEGIN 000000247 xxxxxxxxxxxx Feb 10
14:57:43.19: [ 8557]: HylaFAX (tm) Version 4.2.5 Feb 10 14:57:43.20: [
8557]: <-- [4:ATA\r] Feb 10 14:57:52.32: [ 8557]: --> [5:+FCON] Feb 10
14:57:52.32: [ 8557]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Feb 10 14:57:52.32: [ 8557]: RECV FAX: begin
Feb 10 14:57:52.35: [ 8557]: --> [28:+FTSI:" 0039 xxxx xxxxxx"]
Feb 10 14:57:52.35: [ 8557]: REMOTE TSI "0039 xxxx xxxxxx"
Feb 10 14:57:52.58: [ 8557]: --> [21:+FDCS:0,5,0,2,0,0,0,0] Feb 10
14:57:52.58: [ 8557]: REMOTE wants 14400 bit/s Feb 10 14:57:52.58: [ 8557]:
REMOTE wants A4 page width (215 mm) Feb 10 14:57:52.58: [ 8557]: REMOTE
wants unlimited page length Feb 10 14:57:52.58: [ 8557]: REMOTE wants 3.85
line/mm Feb 10 14:57:52.58: [ 8557]: REMOTE wants 1-D MH Feb 10 14:57:52.59:
[ 8557]: --> [2:OK] Feb 10 14:57:52.59: [ 8557]: <-- [7:AT+FDR\r] Feb 10
14:57:52.62: [ 8557]: --> [8:+FCERROR] Feb 10 15:00:52.62: [ 8557]: REMOTE
HANGUP: Unspecified Phase C error, including too much delay between TCF and
+FDR command (code 90) Feb 10 15:00:52.62: [ 8557]: RECV FAX (000000247):
recvq/fax000000139.tif from 0039 xxxx xxxxxx, route to <unspecified>, 0
pages in 3:00 Feb 10 15:00:52.63: [ 8557]: RECV FAX: Unspecified Phase C
error, including too much delay between TCF and +FDR command Feb 10
15:00:52.63: [ 8557]: <-- [6:AT+FK\r] Feb 10 15:01:22.63: [ 8557]: MODEM
<Timeout> Feb 10 15:01:22.63: [ 8557]: RECV FAX (000000247): session with
0039 xxxx xxxxxx terminated abnormally: Unspecified Phase C error, including
too much delay between TCF and +FDR command Feb 10 15:01:22.63: [ 8557]:
RECV FAX: bin/faxrcvd "recvq/fax000000139.tif" "ttyS0" "000000247"
"Unspecified Phase C error, including too much delay between TCF and +FDR
command"
Feb 10 15:01:22.63: [ 8557]: RECV FAX: end Feb 10 15:01:22.63: [ 8557]:
SESSION END
This is the configuration that use:
CountryCode: 39
AreaCode: 0522
FAXNumber: +390522948555
LongDistancePrefix: 0
InternationalPrefix: "0 "
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Interpump Engineering"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxConsecutiveBadLines: 3
MaxRecvPages: 30
ModemType: Class2
ModemDialCmd: ATDT71,%s
Class2Cmd: AT+FCLASS=2 # command to enter class 2
Class2BORCmd: AT+FBOR=0 # bit order for phase B/C/D (direct)
Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv
Class2CQCmd: "" # commands to enable copy quality
proc.
Class2AbortCmd: AT+FK # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality
capabilities
Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities
Class2TBCCmd: AT+FTBC=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLID # set local identifier command
Class2DCCCmd: AT+FDCC # set modem capabilities command
Class2DISCmd: AT+FDIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FCIG # set polling identifier command
Class2PTSCmd: AT+FPTS # set post-page status command
Class2RecvDataTrigger: "" # character sent to modem to start
recv
Class2XmitWaitForXON: yes # if true, wait for XON before send
Class2SPLCmd: AT+FSPL # set polling indicator command
Class2RecvDataTrigger: "" # character sent to modem to start
recv
Class2XmitWaitForXON: yes # if true, wait for XON before send
Thanks
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
