|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] No Response to PPS
Hi Daniel.
It's unlikely that you will ever get your fax to run over a VoIP line
reliably. If you have a search through the HylaFAX archives you will get a
detailed discussion of why not.
We ran a bunch of tests on a VoIP 'dedicated fax' line in the USA and UK
using a bunch of fax machines, fax modems, and fax boards..... It never
worked reliably. I would suggest that you invest in a POTS line because
it's going to be a lot cheaper than the time you will waste on getting this
to work.
Regards
ANDREW RINALDI
Mainpine Support Manager
USA +1 718 701 2422 | Asia/Europe +44 1225 436137
andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com
-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Daniel Hillhouse
Sent: 13 October 2005 23:47
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] No Response to PPS
Hi Everyone,
I've had Hylafax setup for a week or so now without any problems. I have
moved my line over to VoIP and since then have had issues with "No Response
to PPS repeated 3 times." If I send one or two pages it seems to be fine,
but when I send something bigger I have this error.
The VoIP provider has a specific fax line configured for me but they say it
is only on trial. I was wondering if the issue may be caused from
mis-transmission or Hylafax not waiting long enough for the response.
If this is so, how should I slow down the transmission to make it work more
effectively?
I am using a Class 1 modem. The brand seems Unique to Australia "Spirit
Magnum V.92" and Slackware 10.1
Thanks for any assistance.
Log of a failed job is listed below.
Daniel.
Your facsimile job to 1300363145 failed because:
No response to PPS repeated 3 times.; too many attempts to send
---- Transcript of session follows ----
Oct 13 13:58:25.31: [29855]: SESSION BEGIN 000000056 61031300363145 Oct 13
13:58:25.31: [29855]: HylaFAX (tm) Version 4.2.2 Oct 13 13:58:25.31:
[29855]: SEND FAX: JOB 23 DEST 1300363145 COMMID
000000056 DEVICE '/dev/modem'
Oct 13 13:58:25.31: [29855]: <-- [12:AT+FCLASS=1\r] Oct 13 13:58:25.42:
[29855]: --> [2:OK] Oct 13 13:58:25.43: [29855]: DIAL 1300363145 Oct 13
13:58:25.43: [29855]: <-- [15:ATDT1300363145\r] Oct 13 13:58:43.53: [29855]:
--> [7:CONNECT] Oct 13 13:58:44.80: [29855]: --> [2:OK] Oct 13 13:58:44.80:
[29855]: REMOTE NSF "00 00 56 55 55 00 8C 90 80 FA 00"
Oct 13 13:58:44.80: [29855]: NSF remote fax equipment: Brother Oct 13
13:58:44.80: [29855]: <-- [9:AT+FRH=3\r] Oct 13 13:58:44.81: [29855]: -->
[7:CONNECT] Oct 13 13:58:45.19: [29855]: --> [2:OK] Oct 13 13:58:45.20:
[29855]: REMOTE best rate 14400 bit/s Oct 13 13:58:45.20: [29855]: REMOTE
max A4 page width (215 mm) Oct 13 13:58:45.20: [29855]: REMOTE max unlimited
page length Oct 13 13:58:45.20: [29855]: REMOTE best vres 15.4 line/mm Oct
13 13:58:45.20: [29855]: REMOTE best format 2-D MMR Oct 13 13:58:45.20:
[29855]: REMOTE supports T.30 Annex A, 256-byte ECM Oct 13 13:58:45.20:
[29855]: REMOTE best 10 ms/scanline Oct 13 13:58:45.20: [29855]: USE 14400
bit/s Oct 13 13:58:45.20: [29855]: USE error correction mode Oct 13
13:58:45.20: [29855]: SEND file "docq/doc42.ps;f0"
Oct 13 13:58:45.20: [29855]: USE A4 page width (215 mm) Oct 13 13:58:45.20:
[29855]: USE unlimited page length Oct 13 13:58:45.20: [29855]: USE 3.85
line/mm Oct 13 13:58:45.20: [29855]: USE 2-D MMR Oct 13 13:58:45.20:
[29855]: USE 0 ms/scanline Oct 13 13:58:45.20: [29855]: SEND training at
v.17 14400 bit/s Oct 13 13:58:45.20: [29855]: <-- [9:AT+FRS=7\r] Oct 13
13:58:45.21: [29855]: --> [2:OK] Oct 13 13:58:45.21: [29855]: <--
[9:AT+FTH=3\r] Oct 13 13:58:45.26: [29855]: --> [7:CONNECT] Oct 13
13:58:45.30: [29855]: --> [7:CONNECT] Oct 13 13:58:47.48: [29855]: -->
[2:OK] Oct 13 13:58:47.49: [29855]: <-- [9:AT+FTS=7\r] Oct 13 13:58:47.50:
[29855]: --> [2:OK] Oct 13 13:58:47.51: [29855]: <-- [11:AT+FTM=145\r] Oct
13 13:58:49.18: [29855]: --> [7:CONNECT] Oct 13 13:58:50.74: [29855]: -->
[2:OK] Oct 13 13:58:50.74: [29855]: <-- [9:AT+FRH=3\r] Oct 13 13:58:51.26:
[29855]: --> [7:CONNECT] Oct 13 13:58:52.41: [29855]: --> [2:OK] Oct 13
13:58:52.41: [29855]: TRAINING succeeded Oct 13 13:58:52.41: [29855]: SEND
begin page Oct 13 13:58:52.93: [29855]: SEND EOFB Oct 13 13:58:52.93:
[29855]: SEND send frame number 0 Oct 13 13:58:52.93: [29855]: SEND send
frame number 1 Oct 13 13:58:52.93: [29855]: SEND send frame number 2 .
.
.
Oct 13 13:58:53.37: [29855]: SEND send frame number 218 Oct 13 13:58:53.37:
[29855]: SEND send frame number 219 Oct 13 13:58:53.37: [29855]: DELAY 200
ms Oct 13 13:58:53.56: [29855]: <-- [11:AT+FTM=146\r] Oct 13 13:58:54.06:
[29855]: --> [7:CONNECT] Oct 13 13:59:27.13: [29855]: --> [2:OK] Oct 13
13:59:27.13: [29855]: <-- [9:AT+FTS=7\r] Oct 13 13:59:27.15: [29855]: -->
[2:OK] Oct 13 13:59:27.15: [29855]: <-- [9:AT+FTH=3\r] Oct 13 13:59:27.20:
[29855]: --> [7:CONNECT] Oct 13 13:59:28.62: [29855]: --> [2:OK] Oct 13
13:59:28.62: [29855]: SEND send PPS (partial page signal) Oct 13
13:59:28.62: [29855]: SEND send MPS (more pages, same document) Oct 13
13:59:28.62: [29855]: <-- [9:AT+FRH=3\r] Oct 13 13:59:29.15: [29855]: -->
[7:CONNECT] Oct 13 13:59:30.22: [29855]: --> [2:OK] Oct 13 13:59:30.22:
[29855]: HDLC frame too short (0 bytes) Oct 13 13:59:30.22: [29855]: <--
[9:AT+FRS=7\r] Oct 13 13:59:30.24: [29855]: --> [2:OK] Oct 13 13:59:30.24:
[29855]: <-- [9:AT+FTH=3\r] Oct 13 13:59:30.29: [29855]: --> [7:CONNECT] Oct
13 13:59:31.61: [29855]: --> [2:OK] Oct 13 13:59:31.61: [29855]: SEND send
CRP (command repeat) Oct 13 13:59:31.61: [29855]: <-- [9:AT+FRH=3\r] Oct 13
13:59:34.71: [29855]: --> [0:] Oct 13 13:59:34.71: [29855]: MODEM <Empty
line> Oct 13 13:59:34.91: [29855]: MODEM <Timeout> Oct 13 13:59:34.91:
[29855]: <-- [9:AT+FTH=3\r] Oct 13 13:59:34.96: [29855]: --> [7:CONNECT] Oct
13 13:59:36.38: [29855]: --> [2:OK] Oct 13 13:59:36.38: [29855]: SEND send
PPS (partial page signal) Oct 13 13:59:36.38: [29855]: SEND send MPS (more
pages, same document) Oct 13 13:59:36.38: [29855]: <-- [9:AT+FRH=3\r] Oct 13
13:59:36.96: [29855]: --> [7:CONNECT] Oct 13 13:59:38.83: [29855]: -->
[2:OK] Oct 13 13:59:38.83: [29855]: HDLC frame with bad control field 0xff
Oct 13 13:59:38.83: [29855]: <-- [9:AT+FRS=7\r] Oct 13 13:59:38.85: [29855]:
--> [2:OK] Oct 13 13:59:38.85: [29855]: <-- [9:AT+FTH=3\r] Oct 13
13:59:38.90: [29855]: --> [7:CONNECT] Oct 13 13:59:40.22: [29855]: -->
[2:OK] Oct 13 13:59:40.22: [29855]: SEND send CRP (command repeat) Oct 13
13:59:40.22: [29855]: <-- [9:AT+FRH=3\r] Oct 13 13:59:43.32: [29855]: -->
[0:] Oct 13 13:59:43.32: [29855]: MODEM <Empty line> Oct 13 13:59:43.52:
[29855]: MODEM <Timeout> Oct 13 13:59:43.52: [29855]: <-- [9:AT+FTH=3\r] Oct
13 13:59:43.57: [29855]: --> [7:CONNECT] Oct 13 13:59:44.99: [29855]: -->
[2:OK] Oct 13 13:59:44.99: [29855]: SEND send PPS (partial page signal) Oct
13 13:59:44.99: [29855]: SEND send MPS (more pages, same document) Oct 13
13:59:45.00: [29855]: <-- [9:AT+FRH=3\r] Oct 13 13:59:45.44: [29855]: -->
[7:CONNECT] Oct 13 13:59:47.47: [29855]: --> [2:OK] Oct 13 13:59:47.47:
[29855]: SEND recv PPR (partial page request) Oct 13 13:59:47.47: [29855]:
<-- [9:AT+FRS=7\r] Oct 13 13:59:47.49: [29855]: --> [2:OK] Oct 13
13:59:47.50: [29855]: SEND send frame number 213 Oct 13 13:59:47.50:
[29855]: SEND send frame number 214 Oct 13 13:59:47.50: [29855]: SEND send
frame number 215 Oct 13 13:59:47.50: [29855]: SEND send frame number 216 Oct
13 13:59:47.50: [29855]: SEND send frame number 217 Oct 13 13:59:47.50:
[29855]: SEND send frame number 218 Oct 13 13:59:47.50: [29855]: DELAY 200
ms Oct 13 13:59:47.69: [29855]: <-- [11:AT+FTM=146\r] Oct 13 13:59:48.19:
[29855]: --> [7:CONNECT] Oct 13 13:59:49.58: [29855]: --> [2:OK] Oct 13
13:59:49.58: [29855]: <-- [9:AT+FTS=7\r] Oct 13 13:59:49.60: [29855]: -->
[2:OK] Oct 13 13:59:49.60: [29855]: <-- [9:AT+FTH=3\r] Oct 13 13:59:49.65:
[29855]: --> [7:CONNECT] Oct 13 13:59:51.07: [29855]: --> [2:OK] Oct 13
13:59:51.07: [29855]: SEND send PPS (partial page signal) Oct 13
13:59:51.07: [29855]: SEND send MPS (more pages, same document) Oct 13
13:59:51.07: [29855]: <-- [9:AT+FRH=3\r] Oct 13 13:59:51.54: [29855]: -->
[7:CONNECT] Oct 13 13:59:52.69: [29855]: --> [2:OK] Oct 13 13:59:52.69:
[29855]: SEND recv MCF (message confirmation) Oct 13 13:59:52.69: [29855]:
<-- [9:AT+FRS=7\r] Oct 13 13:59:52.71: [29855]: --> [2:OK] Oct 13
13:59:52.71: [29855]: SEND end page Oct 13 13:59:52.72: [29855]: SEND FAX
(000000056): FROM TO 1300363145 (docq/doc42.ps;f0 sent in 1:07) Oct 13
13:59:52.72: [29855]: SEND FAX (000000056): FROM TO 1300363145 (page 1 of 5
sent in 1:07) Oct 13 13:59:53.73: [29855]: SEND file "docq/doc43.ps;f0"
Oct 13 13:59:53.73: [29855]: SEND begin page Oct 13 13:59:54.05: [29855]:
SEND EOFB Oct 13 13:59:54.05: [29855]: SEND send frame number 0 Oct 13
13:59:54.05: [29855]: SEND send frame number 1 Oct 13 13:59:54.05: [29855]:
SEND send frame number 2 .
.
.
Oct 13 13:59:54.33: [29855]: SEND send frame number 205 Oct 13 13:59:54.33:
[29855]: SEND send frame number 206 Oct 13 13:59:54.33: [29855]: DELAY 200
ms Oct 13 13:59:54.52: [29855]: <-- [11:AT+FTM=146\r] Oct 13 13:59:55.02:
[29855]: --> [7:CONNECT] Oct 13 14:00:26.21: [29855]: --> [2:OK] Oct 13
14:00:26.21: [29855]: <-- [9:AT+FTS=7\r] Oct 13 14:00:26.23: [29855]: -->
[2:OK] Oct 13 14:00:26.23: [29855]: <-- [9:AT+FTH=3\r] Oct 13 14:00:26.28:
[29855]: --> [7:CONNECT] Oct 13 14:00:27.70: [29855]: --> [2:OK] Oct 13
14:00:27.70: [29855]: SEND send PPS (partial page signal) Oct 13
14:00:27.70: [29855]: SEND send MPS (more pages, same document) Oct 13
14:00:27.70: [29855]: <-- [9:AT+FRH=3\r] Oct 13 14:00:28.14: [29855]: -->
[7:CONNECT] Oct 13 14:00:29.29: [29855]: --> [2:OK] Oct 13 14:00:29.29:
[29855]: HDLC frame too short (0 bytes) Oct 13 14:00:29.29: [29855]: <--
[9:AT+FRS=7\r] Oct 13 14:00:29.31: [29855]: --> [2:OK] Oct 13 14:00:29.31:
[29855]: <-- [9:AT+FTH=3\r] Oct 13 14:00:29.36: [29855]: --> [7:CONNECT] Oct
13 14:00:30.68: [29855]: --> [2:OK] Oct 13 14:00:30.68: [29855]: SEND send
CRP (command repeat) Oct 13 14:00:30.68: [29855]: <-- [9:AT+FRH=3\r] Oct 13
14:00:33.78: [29855]: --> [0:] Oct 13 14:00:33.78: [29855]: MODEM <Empty
line> Oct 13 14:00:33.98: [29855]: MODEM <Timeout> Oct 13 14:00:33.98:
[29855]: <-- [9:AT+FTH=3\r] Oct 13 14:00:34.03: [29855]: --> [7:CONNECT] Oct
13 14:00:35.45: [29855]: --> [2:OK] Oct 13 14:00:35.45: [29855]: SEND send
PPS (partial page signal) Oct 13 14:00:35.45: [29855]: SEND send MPS (more
pages, same document) Oct 13 14:00:35.45: [29855]: <-- [9:AT+FRH=3\r] Oct 13
14:00:35.87: [29855]: --> [7:CONNECT] Oct 13 14:00:37.02: [29855]: -->
[2:OK] Oct 13 14:00:37.02: [29855]: HDLC frame too short (0 bytes) Oct 13
14:00:37.02: [29855]: <-- [9:AT+FRS=7\r] Oct 13 14:00:37.04: [29855]: -->
[2:OK] Oct 13 14:00:37.04: [29855]: <-- [9:AT+FTH=3\r] Oct 13 14:00:37.09:
[29855]: --> [7:CONNECT] Oct 13 14:00:38.41: [29855]: --> [2:OK] Oct 13
14:00:38.41: [29855]: SEND send CRP (command repeat) Oct 13 14:00:38.41:
[29855]: <-- [9:AT+FRH=3\r] Oct 13 14:00:41.51: [29855]: --> [0:] Oct 13
14:00:41.51: [29855]: MODEM <Empty line> Oct 13 14:00:41.71: [29855]: MODEM
<Timeout> Oct 13 14:00:41.71: [29855]: <-- [9:AT+FTH=3\r] Oct 13
14:00:41.76: [29855]: --> [7:CONNECT] Oct 13 14:00:43.18: [29855]: -->
[2:OK] Oct 13 14:00:43.18: [29855]: SEND send PPS (partial page signal) Oct
13 14:00:43.18: [29855]: SEND send MPS (more pages, same document) Oct 13
14:00:43.18: [29855]: <-- [9:AT+FRH=3\r] Oct 13 14:00:43.64: [29855]: -->
[7:CONNECT] Oct 13 14:00:44.79: [29855]: --> [2:OK] Oct 13 14:00:44.79:
[29855]: SEND recv MCF (message confirmation) Oct 13 14:00:44.79: [29855]:
<-- [9:AT+FRS=7\r] Oct 13 14:00:44.81: [29855]: --> [2:OK] Oct 13
14:00:44.81: [29855]: SEND end page Oct 13 14:00:44.82: [29855]: SEND FAX
(000000056): FROMTO 1300363145 (docq/doc43.ps;f0 sent in 0:51) Oct 13
14:00:44.82: [29855]: SEND FAX (000000056): FROMTO 1300363145 (page 2 of 5
sent in 0:51) Oct 13 14:00:45.83: [29855]: SEND file "docq/doc44.ps;f0"
Oct 13 14:00:45.83: [29855]: SEND begin page Oct 13 14:00:46.18: [29855]:
SEND EOFB Oct 13 14:00:46.18: [29855]: SEND send frame number 0 Oct 13
14:00:46.18: [29855]: SEND send frame number 1 .
.
.
Oct 13 14:00:46.45: [29855]: SEND send frame number 189 Oct 13 14:00:46.45:
[29855]: SEND send frame number 190 Oct 13 14:00:46.45: [29855]: SEND send
frame number 191 Oct 13 14:00:46.45: [29855]: DELAY 200 ms Oct 13
14:00:46.64: [29855]: <-- [11:AT+FTM=146\r] Oct 13 14:00:47.14: [29855]: -->
[7:CONNECT] Oct 13 14:01:16.14: [29855]: --> [2:OK] Oct 13 14:01:16.14:
[29855]: <-- [9:AT+FTS=7\r] Oct 13 14:01:16.16: [29855]: --> [2:OK] Oct 13
14:01:16.16: [29855]: <-- [9:AT+FTH=3\r] Oct 13 14:01:16.21: [29855]: -->
[7:CONNECT] Oct 13 14:01:17.63: [29855]: --> [2:OK] Oct 13 14:01:17.63:
[29855]: SEND send PPS (partial page signal) Oct 13 14:01:17.63: [29855]:
SEND send MPS (more pages, same document) Oct 13 14:01:17.63: [29855]: <--
[9:AT+FRH=3\r] Oct 13 14:01:19.25: [29855]: --> [7:CONNECT] Oct 13
14:01:20.40: [29855]: --> [2:OK] Oct 13 14:01:20.40: [29855]: SEND recv CRP
(command repeat) Oct 13 14:01:20.40: [29855]: <-- [9:AT+FRS=7\r] Oct 13
14:01:20.42: [29855]: --> [2:OK] Oct 13 14:01:20.42: [29855]: <--
[9:AT+FTH=3\r] Oct 13 14:01:20.47: [29855]: --> [7:CONNECT] Oct 13
14:01:21.89: [29855]: --> [2:OK] Oct 13 14:01:21.89: [29855]: SEND send PPS
(partial page signal) Oct 13 14:01:21.89: [29855]: SEND send MPS (more
pages, same document) Oct 13 14:01:21.89: [29855]: <-- [9:AT+FRH=3\r] Oct 13
14:01:23.62: [29855]: --> [7:CONNECT] Oct 13 14:01:24.77: [29855]: -->
[2:OK] Oct 13 14:01:24.77: [29855]: SEND recv CRP (command repeat) Oct 13
14:01:24.77: [29855]: <-- [9:AT+FRS=7\r] Oct 13 14:01:24.79: [29855]: -->
[2:OK] Oct 13 14:01:24.79: [29855]: <-- [9:AT+FTH=3\r] Oct 13 14:01:24.84:
[29855]: --> [7:CONNECT] Oct 13 14:01:26.26: [29855]: --> [2:OK] Oct 13
14:01:26.26: [29855]: SEND send PPS (partial page signal) Oct 13
14:01:26.26: [29855]: SEND send MPS (more pages, same document) Oct 13
14:01:26.26: [29855]: <-- [9:AT+FRH=3\r] Oct 13 14:01:29.36: [29855]: -->
[0:] Oct 13 14:01:29.36: [29855]: MODEM <Empty line> Oct 13 14:01:29.56:
[29855]: MODEM <Timeout> Oct 13 14:01:29.56: [29855]: <-- [9:AT+FTH=3\r] Oct
13 14:01:29.61: [29855]: --> [7:CONNECT] Oct 13 14:01:31.03: [29855]: -->
[2:OK] Oct 13 14:01:31.03: [29855]: SEND send PPS (partial page signal) Oct
13 14:01:31.03: [29855]: SEND send MPS (more pages, same document) Oct 13
14:01:31.03: [29855]: <-- [9:AT+FRH=3\r] Oct 13 14:01:34.13: [29855]: -->
[0:] Oct 13 14:01:34.13: [29855]: MODEM <Empty line> Oct 13 14:01:34.33:
[29855]: MODEM <Timeout> Oct 13 14:01:34.33: [29855]: No response to PPS
repeated 3 times.
Oct 13 14:01:34.33: [29855]: SEND end page Oct 13 14:01:34.33: [29855]: <--
[9:AT+FTH=3\r] Oct 13 14:01:34.38: [29855]: --> [7:CONNECT] Oct 13
14:01:35.70: [29855]: --> [2:OK] Oct 13 14:01:35.70: [29855]: SEND FAILED:
JOB 23 DEST 1300363145 ERR No response to PPS repeated 3 times.; too many
attempts to send Oct 13 14:01:35.70: [29855]: <-- [5:ATH0\r] Oct 13
14:01:36.13: [29855]: --> [10:NO CARRIER] Oct 13 14:01:36.13: [29855]: MODEM
No carrier Oct 13 14:01:36.14: [29855]: SESSION END
---- Unsent job status ----
Destination: 1300363145
JobID: 23
GroupID: 23
Sender: root
Mailaddr:
CommID: 000000056
Submitted From: localhost
Page Width: 215 (mm)
Page Length: 279 (mm)
Resolution: 98 (lpi)
Status: No response to PPS repeated 3 times.; too many attempts to
send
Dialogs: 3 (exchanges with remote device)
Dials: 0 (consecutive failed calls to destination)
Calls: 3 (total phone calls placed)
Pages: 2 (pages transmitted)
TotPages: 5 (total pages to transmit)
Attempts: 1 (attempts to send current page)
Dirnum: 0 (directory of next page to send)
---- Documents submitted for transmission ----
The following documents were submitted for transmission and are available on
the server for reuse until they are automatically purged when this job is
removed. Documents may also be manually removed using the faxrm command;
consult faxrm(1) for information.
Filename Size Type
docq/doc42.ps 424945 PostScript
docq/doc43.ps 243581 PostScript
docq/doc44.ps 436721 PostScript
docq/doc45.ps 17129 PostScript
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
