|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Problems to receive a facsimile
Hello all,
I am using hylafax 4.2.1. Sending facsimiles works fine but I can not
reveive any facsimiles. At the moment I have no idea what is the
problem. The following lines document the behaviour.
Can anybody help me? At the end of this posting I have added the content
of the file config.ttyS1
Remarks: I only changed my number and the TSI of the sender in this posting.
Thanks in advance!
Frank
Aug 05 12:31:26.46: [ 3517]: SESSION BEGIN 000000008 4937209XXXX
Aug 05 12:31:26.46: [ 3517]: HylaFAX (tm) Version 4.2.1
Aug 05 12:31:26.46: [ 3517]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Aug 05 12:31:26.47: [ 3517]: <-- [4:ATA\r]
Aug 05 12:31:29.47: [ 3517]: --> [7:CONNECT]
Aug 05 12:31:29.47: [ 3517]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS1'
Aug 05 12:31:29.47: [ 3517]: MODEM input buffering enabled
Aug 05 12:31:29.47: [ 3517]: RECV FAX: begin
Aug 05 12:31:29.48: [ 3517]: MODEM input buffering disabled
Aug 05 12:31:29.48: [ 3517]: <-- data [32]
Aug 05 12:31:29.48: [ 3517]: <-- data [2]
Aug 05 12:31:31.35: [ 3517]: --> [7:CONNECT]
Aug 05 12:31:31.35: [ 3517]: <-- data [23]
Aug 05 12:31:31.35: [ 3517]: <-- data [2]
Aug 05 12:31:32.13: [ 3517]: --> [7:CONNECT]
Aug 05 12:31:32.13: [ 3517]: <-- data [10]
Aug 05 12:31:32.13: [ 3517]: <-- data [2]
Aug 05 12:31:32.54: [ 3517]: --> [2:OK]
Aug 05 12:31:32.54: [ 3517]: <-- [9:AT+FRH=3\r]
Aug 05 12:31:33.17: [ 3517]: --> [7:CONNECT]
Aug 05 12:31:34.96: [ 3517]: --> [2:OK]
Aug 05 12:31:34.96: [ 3517]: REMOTE TSI "YYYY"
Aug 05 12:31:34.96: [ 3517]: <-- [9:AT+FRH=3\r]
Aug 05 12:31:35.00: [ 3517]: --> [7:CONNECT]
Aug 05 12:31:35.36: [ 3517]: --> [2:OK]
Aug 05 12:31:35.36: [ 3517]: REMOTE wants 14400 bit/s
Aug 05 12:31:35.36: [ 3517]: REMOTE wants A4 page width (215 mm)
Aug 05 12:31:35.36: [ 3517]: REMOTE wants unlimited page length
Aug 05 12:31:35.36: [ 3517]: REMOTE wants 7.7 line/mm
Aug 05 12:31:35.36: [ 3517]: REMOTE wants 1-D MH
Aug 05 12:31:35.36: [ 3517]: RECV training at v.17 14400 bit/s
Aug 05 12:31:35.36: [ 3517]: MODEM set XON/XOFF/DRAIN: input ignored,
output generated
Aug 05 12:31:35.36: [ 3517]: <-- [11:AT+FRM=145\r]
Aug 05 12:31:37.11: [ 3517]: --> [7:CONNECT]
Aug 05 12:31:38.61: [ 3517]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled
Aug 05 12:31:38.61: [ 3517]: RECV: TCF 2688 bytes, 0% non-zero, 2675
zero-run
Aug 05 12:31:38.62: [ 3517]: --> [10:NO CARRIER]
Aug 05 12:31:38.62: [ 3517]: DELAY 75 ms
Aug 05 12:31:38.70: [ 3517]: TRAINING succeeded
Aug 05 12:31:38.71: [ 3517]: <-- [9:AT+FTH=3\r]
Aug 05 12:31:38.74: [ 3517]: --> [7:CONNECT]
Aug 05 12:31:38.74: [ 3517]: <-- data [3]
Aug 05 12:31:38.74: [ 3517]: <-- data [2]
Aug 05 12:31:39.95: [ 3517]: --> [2:OK]
Aug 05 12:31:39.95: [ 3517]: MODEM input buffering enabled
Aug 05 12:31:39.95: [ 3517]: MODEM set XON/XOFF/FLUSH: input ignored,
output generated
Aug 05 12:31:39.95: [ 3517]: <-- [11:AT+FRM=146\r]
Aug 05 12:31:40.79: [ 3517]: --> [7:CONNECT]
Aug 05 12:31:40.79: [ 3517]: RECV: begin page
Aug 05 12:31:43.80: [ 3517]: RECV: 378 total lines, 0 bad lines, 0
consecutive bad lines
Aug 05 12:31:43.80: [ 3517]: RECV: end page
Aug 05 12:31:43.80: [ 3517]: --> [10:NO CARRIER]
Aug 05 12:31:43.80: [ 3517]: <-- [9:AT+FRH=3\r]
Aug 05 12:31:43.94: [ 3517]: --> [7:CONNECT]
Aug 05 12:31:45.08: [ 3517]: --> [2:OK]
Aug 05 12:31:45.08: [ 3517]: RECV recv EOP (no more pages or documents)
Aug 05 12:31:45.08: [ 3517]: <-- [9:AT+FRS=7\r]
Aug 05 12:32:15.08: [ 3517]: MODEM TIMEOUT: reading line from modem
Aug 05 12:32:15.08: [ 3517]: MODEM <Timeout>
Aug 05 12:32:15.09: [ 3517]: RECV FAX: Failure to receive silence.
Aug 05 12:32:15.09: [ 3517]: <-- [9:AT+FTH=3\r]
Aug 05 12:32:15.09: [ 3517]: RECV FAX (000000008):
recvq/fax000000007.tif from YYYY, route to <unspecified>, 0 pages in 0:46
Aug 05 12:32:15.23: [ 3517]: --> [2:OK]
Aug 05 12:32:15.23: [ 3517]: MODEM input buffering enabled
Aug 05 12:32:15.23: [ 3517]: RECV FAX (000000008): session with AKW
AUTOMOBILE GMBH terminated abnormally: Failure to receive silence.
Aug 05 12:32:15.24: [ 3517]: RECV FAX: bin/faxrcvd
"recvq/fax000000007.tif" "ttyS1" "000000008" "Failure to receive
silence." "" ""
Aug 05 12:32:15.24: [ 3517]: RECV FAX: end
Aug 05 12:32:15.26: [ 3517]: SESSION END
========================================================================
# $Id: class1,v 1.14 2004/04/19 18:44:46 lhoward Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the
names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 49
AreaCode: 37209
FAXNumber: +49.37209.XXXX
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 527
SessionTracing: 527
RecvFileMode: 0666
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 6
SpeakerVolume: 3
GettyArgs: "-r -b -s %s %l"
LocalIdentifier: "Geschner"
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
#ModemRate: 19200 # rate for DCE-DTE communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s # T for tone dialing
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem
is reset
#ModemAnswerCmd: ATA # use this to answer phone
#ModemNoFlowCmd: AT&K # disable flow control cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command
results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook
(hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemSoftResetCmdDelay: 3000 # pause after soft reset
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2
seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for
transmit
#
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait
before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait
before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait
before EOP
Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF &
response
Class1SendMsgDelay: 200 # 75ms delay after training
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and
trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training
failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC
frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
