|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Not receiving fax
Hi all
I've recently installed an hylafax server. I can send fax, but i can't
receive it. It's my system:
System:
- Ubuntu Linux 5.04 x86
- Dynalink 56PMi PCI modem (Conexant HSF 56k HSFi)
(driver hsfmodem-6.03.00lnxt04082400full)
- Hylafax Server / Client 4.2.0 (-16ubuntu0.1)
I get that log on receive:
[LOG]
Jul 11 11:49:38.55: [ 7775]: SESSION BEGIN 000000004 34922152660
Jul 11 11:49:38.57: [ 7775]: HylaFAX (tm) Version 4.2.0
Jul 11 11:49:38.57: [ 7775]: <-- [4:ATA\r]
Jul 11 11:49:43.91: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:43.91: [ 7775]: ANSWER: FAX CONNECTION DEVICE
'/dev/ttySHSF0'
Jul 11 11:49:43.91: [ 7775]: RECV FAX: begin
Jul 11 11:49:44.06: [ 7775]: <-- data [32]
Jul 11 11:49:44.06: [ 7775]: <-- data [2]
Jul 11 11:49:45.60: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:45.60: [ 7775]: <-- data [23]
Jul 11 11:49:45.60: [ 7775]: <-- data [2]
Jul 11 11:49:46.31: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:46.31: [ 7775]: <-- data [10]
Jul 11 11:49:46.31: [ 7775]: <-- data [2]
Jul 11 11:49:46.92: [ 7775]: --> [2:OK]
Jul 11 11:49:46.92: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:49:47.06: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:48.84: [ 7775]: --> [2:OK]
Jul 11 11:49:48.84: [ 7775]: REMOTE TSI "660937"
Jul 11 11:49:48.84: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:49:48.87: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:49.12: [ 7775]: --> [2:OK]
Jul 11 11:49:49.12: [ 7775]: REMOTE wants 9600 bit/s
Jul 11 11:49:49.12: [ 7775]: REMOTE wants A4 page width (215 mm)
Jul 11 11:49:49.12: [ 7775]: REMOTE wants unlimited page length
Jul 11 11:49:49.12: [ 7775]: REMOTE wants 7.7 line/mm
Jul 11 11:49:49.12: [ 7775]: REMOTE wants 1-D MH
Jul 11 11:49:49.12: [ 7775]: RECV training at v.29 9600 bit/s
Jul 11 11:49:49.12: [ 7775]: <-- [10:AT+FRM=96\r]
Jul 11 11:49:49.42: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:50.98: [ 7775]: RECV: TCF 1812 bytes, 67% non-zero, 1
zero-run
Jul 11 11:49:50.98: [ 7775]: RECV: reject TCF (too many non-zero, max
10%)
Jul 11 11:49:50.98: [ 7775]: RECV: reject TCF (zero run too short, min
1200)
Jul 11 11:49:51.00: [ 7775]: --> [10:NO CARRIER]
Jul 11 11:49:51.00: [ 7775]: DELAY 75 ms
Jul 11 11:49:51.07: [ 7775]: <-- [9:AT+FTH=3\r]
Jul 11 11:49:51.39: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:51.39: [ 7775]: <-- data [3]
Jul 11 11:49:51.39: [ 7775]: <-- data [2]
Jul 11 11:49:52.68: [ 7775]: --> [2:OK]
Jul 11 11:49:52.68: [ 7775]: TRAINING failed
Jul 11 11:49:52.68: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:49:52.83: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:54.59: [ 7775]: --> [2:OK]
Jul 11 11:49:54.59: [ 7775]: REMOTE TSI "660937"
Jul 11 11:49:54.59: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:49:54.61: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:54.89: [ 7775]: --> [2:OK]
Jul 11 11:49:54.89: [ 7775]: REMOTE wants 7200 bit/s
Jul 11 11:49:54.89: [ 7775]: REMOTE wants A4 page width (215 mm)
Jul 11 11:49:54.89: [ 7775]: REMOTE wants unlimited page length
Jul 11 11:49:54.89: [ 7775]: REMOTE wants 7.7 line/mm
Jul 11 11:49:54.89: [ 7775]: REMOTE wants 1-D MH
Jul 11 11:49:54.89: [ 7775]: RECV training at v.29 7200 bit/s
Jul 11 11:49:54.89: [ 7775]: <-- [10:AT+FRM=72\r]
Jul 11 11:49:55.19: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:56.72: [ 7775]: RECV: TCF 1332 bytes, 53% non-zero, 1
zero-run
Jul 11 11:49:56.72: [ 7775]: RECV: reject TCF (too many non-zero, max
10%)
Jul 11 11:49:56.72: [ 7775]: RECV: reject TCF (zero run too short, min
900)
Jul 11 11:49:56.74: [ 7775]: --> [10:NO CARRIER]
Jul 11 11:49:56.74: [ 7775]: DELAY 75 ms
Jul 11 11:49:56.82: [ 7775]: <-- [9:AT+FTH=3\r]
Jul 11 11:49:57.14: [ 7775]: --> [7:CONNECT]
Jul 11 11:49:57.14: [ 7775]: <-- data [3]
Jul 11 11:49:57.14: [ 7775]: <-- data [2]
Jul 11 11:49:58.43: [ 7775]: --> [2:OK]
Jul 11 11:49:58.43: [ 7775]: TRAINING failed
Jul 11 11:49:58.43: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:49:58.58: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:00.36: [ 7775]: --> [2:OK]
Jul 11 11:50:00.36: [ 7775]: REMOTE TSI "660937"
Jul 11 11:50:00.36: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:50:00.39: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:00.64: [ 7775]: --> [2:OK]
Jul 11 11:50:00.65: [ 7775]: REMOTE wants 4800 bit/s
Jul 11 11:50:00.65: [ 7775]: REMOTE wants A4 page width (215 mm)
Jul 11 11:50:00.65: [ 7775]: REMOTE wants unlimited page length
Jul 11 11:50:00.65: [ 7775]: REMOTE wants 7.7 line/mm
Jul 11 11:50:00.65: [ 7775]: REMOTE wants 1-D MH
Jul 11 11:50:00.65: [ 7775]: RECV training at v.27ter 4800 bit/s
Jul 11 11:50:00.65: [ 7775]: <-- [10:AT+FRM=48\r]
Jul 11 11:50:05.15: [ 7775]: --> [0:]
Jul 11 11:50:05.15: [ 7775]: MODEM <Empty line>
Jul 11 11:50:05.15: [ 7775]: <-- data [1]
Jul 11 11:50:05.35: [ 7775]: MODEM <Timeout>
Jul 11 11:50:05.35: [ 7775]: DELAY 75 ms
Jul 11 11:50:05.43: [ 7775]: <-- [9:AT+FTH=3\r]
Jul 11 11:50:07.98: [ 7775]: --> [0:]
Jul 11 11:50:07.98: [ 7775]: TRAINING failed
Jul 11 11:50:07.98: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:50:08.02: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:08.32: [ 7775]: --> [5:ERROR]
Jul 11 11:50:08.32: [ 7775]: MODEM Command error
Jul 11 11:50:08.32: [ 7775]: FCS error
Jul 11 11:50:08.32: [ 7775]: DELAY 1500 ms
Jul 11 11:50:09.82: [ 7775]: <-- [9:AT+FTH=3\r]
Jul 11 11:50:10.14: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:10.14: [ 7775]: <-- data [32]
Jul 11 11:50:10.14: [ 7775]: <-- data [2]
Jul 11 11:50:11.93: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:11.93: [ 7775]: <-- data [23]
Jul 11 11:50:11.93: [ 7775]: <-- data [2]
Jul 11 11:50:12.64: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:12.64: [ 7775]: <-- data [10]
Jul 11 11:50:12.64: [ 7775]: <-- data [2]
Jul 11 11:50:13.25: [ 7775]: --> [2:OK]
Jul 11 11:50:13.25: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:50:13.39: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:15.18: [ 7775]: --> [2:OK]
Jul 11 11:50:15.18: [ 7775]: REMOTE TSI "660937"
Jul 11 11:50:15.18: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:50:15.20: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:15.45: [ 7775]: --> [2:OK]
Jul 11 11:50:15.45: [ 7775]: REMOTE wants 4800 bit/s
Jul 11 11:50:15.45: [ 7775]: REMOTE wants A4 page width (215 mm)
Jul 11 11:50:15.45: [ 7775]: REMOTE wants unlimited page length
Jul 11 11:50:15.45: [ 7775]: REMOTE wants 7.7 line/mm
Jul 11 11:50:15.45: [ 7775]: REMOTE wants 1-D MH
Jul 11 11:50:15.45: [ 7775]: RECV training at v.27ter 4800 bit/s
Jul 11 11:50:15.45: [ 7775]: <-- [10:AT+FRM=48\r]
Jul 11 11:50:19.95: [ 7775]: --> [0:]
Jul 11 11:50:19.95: [ 7775]: MODEM <Empty line>
Jul 11 11:50:19.95: [ 7775]: <-- data [1]
Jul 11 11:50:20.16: [ 7775]: MODEM <Timeout>
Jul 11 11:50:20.16: [ 7775]: DELAY 75 ms
Jul 11 11:50:20.23: [ 7775]: <-- [9:AT+FTH=3\r]
Jul 11 11:50:22.78: [ 7775]: --> [0:]
Jul 11 11:50:22.78: [ 7775]: TRAINING failed
Jul 11 11:50:22.78: [ 7775]: <-- [9:AT+FRH=3\r]
Jul 11 11:50:22.82: [ 7775]: --> [7:CONNECT]
Jul 11 11:50:27.82: [ 7775]: <-- data [1]
Jul 11 11:50:27.93: [ 7775]: --> [2:OK]
Jul 11 11:50:27.93: [ 7775]: RECV FAX: Failure to train modems
Jul 11 11:50:27.93: [ 7775]: RECV FAX: end
Jul 11 11:50:27.93: [ 7775]: SESSION END
[/LOG]
And this are my config files:
[config.ttySHSF0]
CountryCode: 34
AreaCode: 922
FAXNumber: +34.922.111111
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 2
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Organica DTM"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "De %%l|%c|Página %%P de %%T"
MaxRecvPages: 100
ModemType: Class1 # use this to supply a hint
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: rtscts # default
#
ModemNoFlowCmd: AT&K0 # setup no flow control
ModemHardFlowCmd: AT&K3 # setup hardware flow control
ModemSoftFlowCmd: AT&K4 # setup software flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier
(or not)
#
ModemMfrQueryCmd: !Rockwell
ModemModelQueryCmd: !RC288DPi
ModemRevQueryCmd: ATI3 # product information
#
ModemDialCmd: ATDT%s # T for tone dialing
[/config.ttySHSF0]
[hyla.conf]
#
# /etc/hylafax/hyla.conf
#
# System-wide client configuration file
# System-wide configuration information
# -------------------------------------
# Host - host to contact for service
#
Host: localhost
# Verbose - whether or not to enable protocol tracing
#
Verbose: No
# Faxstat configuration information
# ---------------------------------
# TimeZone - control whether the times and dates are reported in the
local
# timezone of the server (`local') or in GMT (`GMT').
#
TimeZone: local
# Sendfax configuration information
# ---------------------------------
# DialRules - file containing dialstring rules
#
DialRules: "/etc/hylafax/dialrules"
# If you don't want to have cover pages added automatically for every
fax send
# by "sendfax", please uncomment the following line.
# AutoCoverPage: No
# FontMap/FontPath added by faxsetup (vie jul 8 16:22:24 WEST 2005)
FontMap: /usr/share/gs-esp/7.07/lib:/usr/share/gs-esp/fonts:/var/lib/defoma/gs.d/dirs/fonts:/usr/share/cups/fonts:/usr/share/ghostscript/fonts:/usr/local/lib/ghostscript/fonts
FontPath: /usr/share/gs-esp/7.07/lib:/usr/share/gs-esp/fonts:/var/lib/defoma/gs.d/dirs/fonts:/usr/share/cups/fonts:/usr/share/ghostscript/fonts:/usr/local/lib/ghostscript/fonts
[/hyla.conf]
[hosts.hfaxd] #ricardo is my user account
# hosts.hfaxd
# This file contains permissions and password for every user in
# the system.
#
# For more information on this biject, please see its man page
# and the commands faxadduser and faxdeluser.
^ricardo@localhost::MYENCPASSW:MYENCPASSW
localhost:21::
127.0.0.1
[/host.hfaxd]
I've heard something about user owner of some files... could it be (i
can send fax perfectly, but not receive confirmation email message)
Thanks a lot.
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
