|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] TR: Send But no recieve
Malheureusement j'ai déjà fais le teste avec ces fichiers de configuration
Je pense avoir loupé quelque chose mais quoi !!!?
-----Message d'origine-----
De : Y BAESA [mailto:ybaesa@xxxxxxxxxx]
Envoyé : mercredi 1 juin 2005 17:19
À : alban Coujard
Objet : Re: [hylafax-users] Send But no recieve
Bonjour,
Vous devriez essayer les config suivantes qui se trouvent
sous /var/spool/hylafax/config
soit usr-rts
soit usr-xon
dans notre entreprise
nous avons des modems USR 56K et des sportster flash 33.6k
soit 6 avec hylafax 4.1.8 et sur une machine de test hylafax 4.2.1 en
test et ca fonctionne.
A+
Y BAESA
> When I do [root@amonbofis hylafax-4.2.1]# faxanswer ttyS0
>
> I have got this:
>
> [root@amonbofis hylafax-4.2.1]# cat /var/spool/hylafax/log/c000000002
> jun 01 16:19:00.50: [26023]: SESSION BEGIN 000000002 384494804
> jun 01 16:19:00.50: [26023]: HylaFAX (tm) Version 4.2.0
> jun 01 16:19:00.50: [26023]: <-- [13:AT+FCLASS=1A\r]
> jun 01 16:19:05.28: [26023]: --> [7:CONNECT]
> jun 01 16:19:05.28: [26023]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
> jun 01 16:19:05.28: [26023]: RECV FAX: begin
> jun 01 16:19:05.28: [26023]: <-- data [32]
> jun 01 16:19:05.28: [26023]: <-- data [2]
> jun 01 16:19:05.35: [26023]: --> [7:CONNECT]
> jun 01 16:19:05.35: [26023]: <-- data [23]
> jun 01 16:19:05.35: [26023]: <-- data [2]
> jun 01 16:19:06.07: [26023]: --> [7:CONNECT]
> jun 01 16:19:06.07: [26023]: <-- data [10]
> jun 01 16:19:06.07: [26023]: <-- data [2]
> jun 01 16:19:08.25: [26023]: --> [2:OK]
> jun 01 16:19:08.25: [26023]: <-- [9:AT+FRH=3\r]
> jun 01 16:19:11.35: [26023]: --> [0:]
> jun 01 16:19:11.35: [26023]: MODEM <Empty line>
> jun 01 16:19:11.35: [26023]: <-- data [1]
> jun 01 16:19:11.36: [26023]: --> [2:OK]
> jun 01 16:19:11.36: [26023]: DELAY 1500 ms
> jun 01 16:19:12.86: [26023]: <-- [9:AT+FTH=3\r]
> jun 01 16:19:12.89: [26023]: --> [7:CONNECT]
> jun 01 16:19:12.89: [26023]: <-- data [32]
> jun 01 16:19:12.89: [26023]: <-- data [2]
> jun 01 16:19:13.06: [26023]: --> [7:CONNECT]
> jun 01 16:19:13.06: [26023]: <-- data [23]
> jun 01 16:19:13.06: [26023]: <-- data [2]
> jun 01 16:19:13.78: [26023]: --> [7:CONNECT]
> jun 01 16:19:13.78: [26023]: <-- data [10]
> jun 01 16:19:13.78: [26023]: <-- data [2]
> jun 01 16:19:15.96: [26023]: --> [2:OK]
> jun 01 16:19:15.96: [26023]: <-- [9:AT+FRH=3\r]
> jun 01 16:19:19.07: [26023]: --> [0:]
> jun 01 16:19:19.07: [26023]: MODEM <Empty line>
> jun 01 16:19:19.07: [26023]: <-- data [1]
> jun 01 16:19:19.07: [26023]: --> [2:OK]
> jun 01 16:19:19.07: [26023]: DELAY 1500 ms
> jun 01 16:19:20.59: [26023]: <-- [9:AT+FTH=3\r]
> jun 01 16:19:20.63: [26023]: --> [7:CONNECT]
> jun 01 16:19:20.63: [26023]: <-- data [32]
> jun 01 16:19:20.63: [26023]: <-- data [2]
> jun 01 16:19:20.79: [26023]: --> [7:CONNECT]
> jun 01 16:19:20.79: [26023]: <-- data [23]
> jun 01 16:19:20.79: [26023]: <-- data [2]
> jun 01 16:19:21.51: [26023]: --> [7:CONNECT]
> jun 01 16:19:21.51: [26023]: <-- data [10]
> jun 01 16:19:21.51: [26023]: <-- data [2]
> jun 01 16:19:23.70: [26023]: --> [2:OK]
> jun 01 16:19:23.70: [26023]: <-- [9:AT+FRH=3\r]
> jun 01 16:19:26.80: [26023]: --> [0:]
> jun 01 16:19:26.80: [26023]: MODEM <Empty line>
> jun 01 16:19:26.80: [26023]: <-- data [1]
> jun 01 16:19:26.81: [26023]: --> [2:OK]
> jun 01 16:19:26.81: [26023]: DELAY 1500 ms
> jun 01 16:19:28.31: [26023]: <-- [9:AT+FTH=3\r]
> jun 01 16:19:28.34: [26023]: --> [7:CONNECT]
> jun 01 16:19:28.34: [26023]: <-- data [32]
> jun 01 16:19:28.34: [26023]: <-- data [2]
> jun 01 16:19:28.51: [26023]: --> [7:CONNECT]
> jun 01 16:19:28.51: [26023]: <-- data [23]
> jun 01 16:19:28.51: [26023]: <-- data [2]
> jun 01 16:19:29.23: [26023]: --> [7:CONNECT]
> jun 01 16:19:29.23: [26023]: <-- data [10]
> jun 01 16:19:29.23: [26023]: <-- data [2]
> jun 01 16:19:31.41: [26023]: --> [2:OK]
> jun 01 16:19:31.41: [26023]: <-- [9:AT+FRH=3\r]
> jun 01 16:19:34.51: [26023]: --> [0:]
> jun 01 16:19:34.51: [26023]: MODEM <Empty line>
> jun 01 16:19:34.51: [26023]: <-- data [1]
> jun 01 16:19:34.52: [26023]: --> [2:OK]
> jun 01 16:19:34.52: [26023]: DELAY 1500 ms
> jun 01 16:19:36.02: [26023]: <-- [9:AT+FTH=3\r]
> jun 01 16:19:36.05: [26023]: --> [7:CONNECT]
> jun 01 16:19:36.05: [26023]: <-- data [32]
> jun 01 16:19:36.05: [26023]: <-- data [2]
> jun 01 16:19:36.22: [26023]: --> [7:CONNECT]
> jun 01 16:19:36.22: [26023]: <-- data [23]
> jun 01 16:19:36.22: [26023]: <-- data [2]
> jun 01 16:19:36.94: [26023]: --> [7:CONNECT]
> jun 01 16:19:36.94: [26023]: <-- data [10]
> jun 01 16:19:36.94: [26023]: <-- data [2]
> jun 01 16:19:39.12: [26023]: --> [2:OK]
> jun 01 16:19:39.12: [26023]: <-- [9:AT+FRH=3\r]
> jun 01 16:19:42.22: [26023]: --> [0:]
> jun 01 16:19:42.22: [26023]: MODEM <Empty line>
> jun 01 16:19:42.22: [26023]: <-- data [1]
> jun 01 16:19:42.23: [26023]: --> [2:OK]
> jun 01 16:19:42.23: [26023]: DELAY 1500 ms
> jun 01 16:19:43.73: [26023]: <-- [9:AT+FTH=3\r]
> jun 01 16:19:43.77: [26023]: --> [7:CONNECT]
> jun 01 16:19:43.77: [26023]: <-- data [32]
> jun 01 16:19:43.77: [26023]: <-- data [2]
> jun 01 16:19:43.93: [26023]: --> [7:CONNECT]
> jun 01 16:19:43.93: [26023]: <-- data [23]
> jun 01 16:19:43.93: [26023]: <-- data [2]
> jun 01 16:19:44.65: [26023]: --> [7:CONNECT]
> jun 01 16:19:44.65: [26023]: <-- data [10]
> jun 01 16:19:44.65: [26023]: <-- data [2]
> jun 01 16:19:46.84: [26023]: --> [2:OK]
> jun 01 16:19:46.84: [26023]: <-- [9:AT+FRH=3\r]
> jun 01 16:19:49.94: [26023]: --> [0:]
> jun 01 16:19:49.94: [26023]: MODEM <Empty line>
> jun 01 16:19:49.94: [26023]: <-- data [1]
> jun 01 16:19:49.95: [26023]: --> [2:OK]
> jun 01 16:19:49.95: [26023]: RECV FAX: No answer (T.30 T1 timeout)
> jun 01 16:19:49.95: [26023]: RECV FAX: end
> jun 01 16:19:49.95: [26023]: SESSION END
>
>
> >Yes with a fax machine, I can send fax and recieve with the fax machine,
and
> >sand with halyfax
>
> Le mercredi 1 Juin 2005 14:27, vous avez écrit :
> > Have you tested the line with a fax machine or a
> > different modem?
> >
> > --- alban Coujard <acoujard@xxxxxxxxxxx> wrote:
> > > Yes , When I call the fax number it ring but the
> > > moden do not respond
> > >
> > > Le mercredi 1 Juin 2005 13:54, vous avez écrit :
> > > > Did you rerun init? Ie, init q?
> > > >
> > > > --- alban Coujard <acoujard@xxxxxxxxxxx> wrote:
> > > > > Hello
> > > > >
> > > > > I used a USR Sportster Voice 33.6 Fax Modem, I
> > >
> > > can
> > >
> > > > > send Fax but Can't
> > > > > receive... On a mandrake 10.1, the modem is on
> > >
> > > the
> > >
> > > > > serial port 2 (ttyS1),
> > > > > hylafax 4.2,
> > > > >
> > > > > I dont forget to do #faxgetty ttyS1
> > > > >
> > > > > My config.ttyS1 file is :
> > > > >
> > > > > CountryCode: 33
> > > > > AreaCode: 3
> > > > > FAXNumber: +33.03.xxxxxxxx
> > > > > LongDistancePrefix: 0
> > > > > InternationalPrefix: 00
> > > > > DialStringRules: etc/dialrules
> > > > > ServerTracing: 1
> > > > > SessionTracing: 11
> > > > > RecvFileMode: 0600
> > > > > LogFileMode: 0600
> > > > > DeviceMode: 0600
> > > > > RingsBeforeAnswer: 1
> > > > > SpeakerVolume: quiet
> > > > > GettyArgs: "-h %l dx_%s"
> > > > > LocalIdentifier: "NothingSetup"
> > > > > TagLineFont: etc/lutRS18.pcf
> > > > > TagLineFormat: "From %%l|%c|Page %%P of %%T"
> > > > > MaxRecvPages: 25
> > > > > #
> > > > > #
> > > > > # Modem-related stuff: should reflect modem
> > >
> > > command
> > >
> > > > > interface
> > > > > # and hardware connection/cabling (e.g. flow
> > > > > control).
> > > > > #
> > > > > ModemType: Class1 # use class 1 interface
> > > > > ModemRate: 19200 # rate for DCE-DTE
> > >
> > > communication
> > >
> > > > > ModemFlowControl: xonxoff # software flow
> > >
> > > control
> > >
> > > > > #
> > > > > ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop
> > > > > resets modem
> > > > > ModemSetupDCDCmd: AT&C1 # setup so DCD reflects
> > > > > carrier (or not)
> > > > > ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for
> > >
> > > no
> > >
> > > > > flow control
> > > > > ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for
> > > > > hardware flow control
> > > > > ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for
> > > > > software flow control
> > > > > ModemResultCodesCmd: ATQ0X4 # enable result
> > >
> > > codes
> > >
> > > > > #
> > > > > ModemMfrQueryCmd: !USR
> > > > > ModemModelQueryCmd: ATI3
> > > > > ModemRevQueryCmd: ATI7 # XXX returns a
> > >
> > > multi-line
> > >
> > > > > result
> > > > > #
> > > > > # When AT+FCLASS=1 is issued the modem
> > >
> > > automatically
> > >
> > > > > switches
> > > > > # to software flow control; these parameters let
> > >
> > > the
> > >
> > > > > fax software
> > > > > # reset flow control as needed after entering
> > >
> > > Class
> > >
> > > > > 1.
> > > > > #
> > > > > Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no
> > > > > flow control
> > > > > Class1HFLOCmd: AT&H1&I0&R2 # setup modem for
> > > > > hardware flow control
> > > > > Class1SFLOCmd: "" # modem does this
> > >
> > > automatically
> > >
> > > > > #
> > > > > # This should resolve "DIS/DTC received 3 times"
> > > > > errors:
> > > > > #
> > > > > Class1ResponseWaitCmd: AT+FRS=1 # wait after
> > >
> > > sending
> > >
> > > > > TCF for response
> > > > > #
> > > > > # The remainder of this configuration is
> > >
> > > included so
> > >
> > > > > that the
> > > > > # modem "idles" in Class 0 while not sending or
> > > > > receiving facsimile.
> > > > > #
> > > > > ModemSetupAACmd: AT+FCLASS=0 # leave modem
> > >
> > > idling in
> > >
> > > > > class 0
> > > > > ModemAnswerCmd: AT+FCLASS=1A # answer in Class
> > >
> > > 1
> > >
> > > > > #
> > > > > # Disables the reporting of bad frames by the
> > >
> > > modem.
> > >
> > > > > This
> > > > > # overcomes a firmware problem in the x2 and V90
> > > > > Sportsters.
> > > > > # It is not necessary for the Courier modem.
> > > > > #
> > > > > Class2NRCmd: AT+FNR=1,1,1,0
> > > > >
> > > > > probemodem command result is :
> > > > >
> > > > > This looks like a Class 1 and 2.0 modem.
> > > > >
> > > > > ATI0 RESULT = "OK" RESPONSE = "3361"
> > > > > ATI1 RESULT = "OK" RESPONSE = "966D"
> > > > > ATI2 RESULT = "OK" RESPONSE = "OK"
> > > > > ATI3 RESULT = "OK" RESPONSE = "USRobotics
> > > > > Sportster Voice 33600 Fax Rev.
> > > > > 2.0"
> > > > > ATI4 RESULT = "OK" RESPONSE = "USRobotics
> > > > > Sportster Voice 33600 Fax
> > > > > Settings..."
> > > > > ATI5 RESULT = "Strike a key when ready . . ."
> > > > > RESPONSE = "USRobotics
> > > > > Sportster Voice 33600 Fax NVRAM Settings..."
> > > > > ATI6 RESULT = "OK" RESPONSE = "USRobotics
> > > > > Sportster Voice 33600 Fax Link
> > > > > Diagnostics..."
> > > > > ATI7 RESULT = "OK" RESPONSE =
> > >
> > > "Configuration
> > >
> > > > > Profile..."
> > > > > ATI8 RESULT = "OK" RESPONSE = "Blacklist"
> > > > > ATI9 RESULT = "OK" RESPONSE =
> > > > > "(1.0USR0007\Modem\Sportster 33600
> > > > > FAX/VOICE EXT)FF"
> > > > >
> > > > > Class 1 stuff...
> > > > >
> > > > > AT+FCLASS=? RESULT = "OK" RESPONSE =
> > >
> > > "0,1,2.0"
> > >
> > > > > AT+FCLASS? RESULT = "OK" RESPONSE = "0"
> > > > > AT+FCLASS=0 RESULT = "OK" RESPONSE = "OK"
> > > > > AT+FCLASS=1 RESULT = "OK" RESPONSE = "OK"
> > > > > AT+FCLASS? RESULT = "OK" RESPONSE = "1"
> > > > > AT+FJUNK=? RESULT = "ERROR" RESPONSE
> > >
> > > =
> > >
> > > > > "ERROR"
> > > > > AT+FJUNK? RESULT = "ERROR" RESPONSE
> > >
> > > =
> > >
> > > > > "ERROR"
> > > > > AT+FAA=? RESULT = "OK" RESPONSE =
> > >
> > > "(0,1)"
> > >
> > > > > AT+FAA? RESULT = "OK" RESPONSE = "0"
> > > > > AT+FAE=? RESULT = "ERROR" RESPONSE
> > >
> > > =
> > >
> > > > > "ERROR"
> > > > > AT+FAE? RESULT = "ERROR" RESPONSE =
> > >
> > > "ERROR"
> > >
> > > > > AT+FTH=? RESULT = "OK" RESPONSE =
> > > > > "3,24,48,72,73,74,96,97,98,121,122,145,146"
> > > > > AT+FRH=? RESULT = "OK" RESPONSE =
> > > > > "3,24,48,72,73,74,96,97,98,121,122,145,146"
> > > > > AT+FTM=? RESULT = "OK" RESPONSE =
> > > > > "3,24,48,72,73,74,96,97,98,121,122,145,146"
> > > > > AT+FRM=? RESULT = "OK" RESPONSE =
> > > > > "3,24,48,72,73,74,96,97,98,121,122,145,146"
> > > > > AT+FTS=? RESULT = "ERROR" RESPONSE
> > >
> > > =
> > >
> > > > > "ERROR"
> > > > > AT+FRS=? RESULT = "ERROR" RESPONSE
> > >
> > > =
> > >
> > > > > "ERROR"
> > > > > Class 2.0 stuff...
> > > > >
> > > > > AT+FCLASS=? RESULT = "OK" RESPONSE =
> > >
> > > "0,1,2.0"
> > >
> > > > > AT+FCLASS? RESULT = "OK" RESPONSE = "1"
> > > > > AT+FCLASS=0 RESULT = "OK" RESPONSE = "OK"
> > > > > AT+FCLASS=1 RESULT = "OK" RESPONSE = "OK"
> > > > > AT+FCLASS=2.0 RESULT = "OK" RESPONSE = "OK"
> > > > > AT+FCLASS? RESULT = "OK" RESPONSE = "1"
> > > > > AT+FJU=? RESULT = "ERROR" RESPONSE
> > >
> > > =
> > >
> > > > > "ERROR"
> > > > > AT+FJU? RESULT = "ERROR" RESPONSE =
> > >
> > > "ERROR"
> > >
> > > > > AT+FDR=? RESULT = "" RESPONSE = ""
> > > > > AT+FDT=? RESULT = "" RESPONSE = ""
> > > > > AT+FIP=? RESULT = "ERROR" RESPONSE
> > >
> > > =
> > >
> > > > > "ERROR"
> > > > > AT+FAA=? RESULT = "OK" RESPONSE =
> > >
> > > "(0,1)"
>
> ____________________ HylaFAX(tm) Users Mailing List
_______________________
> To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
/dev/null
> *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
>
>
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
