|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Send But no recieve
When I do [root@amonbofis hylafax-4.2.1]# faxanswer ttyS0
I have got this:
[root@amonbofis hylafax-4.2.1]# cat /var/spool/hylafax/log/c000000002
jun 01 16:19:00.50: [26023]: SESSION BEGIN 000000002 384494804
jun 01 16:19:00.50: [26023]: HylaFAX (tm) Version 4.2.0
jun 01 16:19:00.50: [26023]: <-- [13:AT+FCLASS=1A\r]
jun 01 16:19:05.28: [26023]: --> [7:CONNECT]
jun 01 16:19:05.28: [26023]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
jun 01 16:19:05.28: [26023]: RECV FAX: begin
jun 01 16:19:05.28: [26023]: <-- data [32]
jun 01 16:19:05.28: [26023]: <-- data [2]
jun 01 16:19:05.35: [26023]: --> [7:CONNECT]
jun 01 16:19:05.35: [26023]: <-- data [23]
jun 01 16:19:05.35: [26023]: <-- data [2]
jun 01 16:19:06.07: [26023]: --> [7:CONNECT]
jun 01 16:19:06.07: [26023]: <-- data [10]
jun 01 16:19:06.07: [26023]: <-- data [2]
jun 01 16:19:08.25: [26023]: --> [2:OK]
jun 01 16:19:08.25: [26023]: <-- [9:AT+FRH=3\r]
jun 01 16:19:11.35: [26023]: --> [0:]
jun 01 16:19:11.35: [26023]: MODEM <Empty line>
jun 01 16:19:11.35: [26023]: <-- data [1]
jun 01 16:19:11.36: [26023]: --> [2:OK]
jun 01 16:19:11.36: [26023]: DELAY 1500 ms
jun 01 16:19:12.86: [26023]: <-- [9:AT+FTH=3\r]
jun 01 16:19:12.89: [26023]: --> [7:CONNECT]
jun 01 16:19:12.89: [26023]: <-- data [32]
jun 01 16:19:12.89: [26023]: <-- data [2]
jun 01 16:19:13.06: [26023]: --> [7:CONNECT]
jun 01 16:19:13.06: [26023]: <-- data [23]
jun 01 16:19:13.06: [26023]: <-- data [2]
jun 01 16:19:13.78: [26023]: --> [7:CONNECT]
jun 01 16:19:13.78: [26023]: <-- data [10]
jun 01 16:19:13.78: [26023]: <-- data [2]
jun 01 16:19:15.96: [26023]: --> [2:OK]
jun 01 16:19:15.96: [26023]: <-- [9:AT+FRH=3\r]
jun 01 16:19:19.07: [26023]: --> [0:]
jun 01 16:19:19.07: [26023]: MODEM <Empty line>
jun 01 16:19:19.07: [26023]: <-- data [1]
jun 01 16:19:19.07: [26023]: --> [2:OK]
jun 01 16:19:19.07: [26023]: DELAY 1500 ms
jun 01 16:19:20.59: [26023]: <-- [9:AT+FTH=3\r]
jun 01 16:19:20.63: [26023]: --> [7:CONNECT]
jun 01 16:19:20.63: [26023]: <-- data [32]
jun 01 16:19:20.63: [26023]: <-- data [2]
jun 01 16:19:20.79: [26023]: --> [7:CONNECT]
jun 01 16:19:20.79: [26023]: <-- data [23]
jun 01 16:19:20.79: [26023]: <-- data [2]
jun 01 16:19:21.51: [26023]: --> [7:CONNECT]
jun 01 16:19:21.51: [26023]: <-- data [10]
jun 01 16:19:21.51: [26023]: <-- data [2]
jun 01 16:19:23.70: [26023]: --> [2:OK]
jun 01 16:19:23.70: [26023]: <-- [9:AT+FRH=3\r]
jun 01 16:19:26.80: [26023]: --> [0:]
jun 01 16:19:26.80: [26023]: MODEM <Empty line>
jun 01 16:19:26.80: [26023]: <-- data [1]
jun 01 16:19:26.81: [26023]: --> [2:OK]
jun 01 16:19:26.81: [26023]: DELAY 1500 ms
jun 01 16:19:28.31: [26023]: <-- [9:AT+FTH=3\r]
jun 01 16:19:28.34: [26023]: --> [7:CONNECT]
jun 01 16:19:28.34: [26023]: <-- data [32]
jun 01 16:19:28.34: [26023]: <-- data [2]
jun 01 16:19:28.51: [26023]: --> [7:CONNECT]
jun 01 16:19:28.51: [26023]: <-- data [23]
jun 01 16:19:28.51: [26023]: <-- data [2]
jun 01 16:19:29.23: [26023]: --> [7:CONNECT]
jun 01 16:19:29.23: [26023]: <-- data [10]
jun 01 16:19:29.23: [26023]: <-- data [2]
jun 01 16:19:31.41: [26023]: --> [2:OK]
jun 01 16:19:31.41: [26023]: <-- [9:AT+FRH=3\r]
jun 01 16:19:34.51: [26023]: --> [0:]
jun 01 16:19:34.51: [26023]: MODEM <Empty line>
jun 01 16:19:34.51: [26023]: <-- data [1]
jun 01 16:19:34.52: [26023]: --> [2:OK]
jun 01 16:19:34.52: [26023]: DELAY 1500 ms
jun 01 16:19:36.02: [26023]: <-- [9:AT+FTH=3\r]
jun 01 16:19:36.05: [26023]: --> [7:CONNECT]
jun 01 16:19:36.05: [26023]: <-- data [32]
jun 01 16:19:36.05: [26023]: <-- data [2]
jun 01 16:19:36.22: [26023]: --> [7:CONNECT]
jun 01 16:19:36.22: [26023]: <-- data [23]
jun 01 16:19:36.22: [26023]: <-- data [2]
jun 01 16:19:36.94: [26023]: --> [7:CONNECT]
jun 01 16:19:36.94: [26023]: <-- data [10]
jun 01 16:19:36.94: [26023]: <-- data [2]
jun 01 16:19:39.12: [26023]: --> [2:OK]
jun 01 16:19:39.12: [26023]: <-- [9:AT+FRH=3\r]
jun 01 16:19:42.22: [26023]: --> [0:]
jun 01 16:19:42.22: [26023]: MODEM <Empty line>
jun 01 16:19:42.22: [26023]: <-- data [1]
jun 01 16:19:42.23: [26023]: --> [2:OK]
jun 01 16:19:42.23: [26023]: DELAY 1500 ms
jun 01 16:19:43.73: [26023]: <-- [9:AT+FTH=3\r]
jun 01 16:19:43.77: [26023]: --> [7:CONNECT]
jun 01 16:19:43.77: [26023]: <-- data [32]
jun 01 16:19:43.77: [26023]: <-- data [2]
jun 01 16:19:43.93: [26023]: --> [7:CONNECT]
jun 01 16:19:43.93: [26023]: <-- data [23]
jun 01 16:19:43.93: [26023]: <-- data [2]
jun 01 16:19:44.65: [26023]: --> [7:CONNECT]
jun 01 16:19:44.65: [26023]: <-- data [10]
jun 01 16:19:44.65: [26023]: <-- data [2]
jun 01 16:19:46.84: [26023]: --> [2:OK]
jun 01 16:19:46.84: [26023]: <-- [9:AT+FRH=3\r]
jun 01 16:19:49.94: [26023]: --> [0:]
jun 01 16:19:49.94: [26023]: MODEM <Empty line>
jun 01 16:19:49.94: [26023]: <-- data [1]
jun 01 16:19:49.95: [26023]: --> [2:OK]
jun 01 16:19:49.95: [26023]: RECV FAX: No answer (T.30 T1 timeout)
jun 01 16:19:49.95: [26023]: RECV FAX: end
jun 01 16:19:49.95: [26023]: SESSION END
>Yes with a fax machine, I can send fax and recieve with the fax machine, and
>sand with halyfax
Le mercredi 1 Juin 2005 14:27, vous avez écrit :
> Have you tested the line with a fax machine or a
> different modem?
>
> --- alban Coujard <acoujard@xxxxxxxxxxx> wrote:
> > Yes , When I call the fax number it ring but the
> > moden do not respond
> >
> > Le mercredi 1 Juin 2005 13:54, vous avez écrit :
> > > Did you rerun init? Ie, init q?
> > >
> > > --- alban Coujard <acoujard@xxxxxxxxxxx> wrote:
> > > > Hello
> > > >
> > > > I used a USR Sportster Voice 33.6 Fax Modem, I
> >
> > can
> >
> > > > send Fax but Can't
> > > > receive... On a mandrake 10.1, the modem is on
> >
> > the
> >
> > > > serial port 2 (ttyS1),
> > > > hylafax 4.2,
> > > >
> > > > I dont forget to do #faxgetty ttyS1
> > > >
> > > > My config.ttyS1 file is :
> > > >
> > > > CountryCode: 33
> > > > AreaCode: 3
> > > > FAXNumber: +33.03.xxxxxxxx
> > > > LongDistancePrefix: 0
> > > > InternationalPrefix: 00
> > > > DialStringRules: etc/dialrules
> > > > ServerTracing: 1
> > > > SessionTracing: 11
> > > > RecvFileMode: 0600
> > > > LogFileMode: 0600
> > > > DeviceMode: 0600
> > > > RingsBeforeAnswer: 1
> > > > SpeakerVolume: quiet
> > > > GettyArgs: "-h %l dx_%s"
> > > > LocalIdentifier: "NothingSetup"
> > > > TagLineFont: etc/lutRS18.pcf
> > > > TagLineFormat: "From %%l|%c|Page %%P of %%T"
> > > > MaxRecvPages: 25
> > > > #
> > > > #
> > > > # Modem-related stuff: should reflect modem
> >
> > command
> >
> > > > interface
> > > > # and hardware connection/cabling (e.g. flow
> > > > control).
> > > > #
> > > > ModemType: Class1 # use class 1 interface
> > > > ModemRate: 19200 # rate for DCE-DTE
> >
> > communication
> >
> > > > ModemFlowControl: xonxoff # software flow
> >
> > control
> >
> > > > #
> > > > ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop
> > > > resets modem
> > > > ModemSetupDCDCmd: AT&C1 # setup so DCD reflects
> > > > carrier (or not)
> > > > ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for
> >
> > no
> >
> > > > flow control
> > > > ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for
> > > > hardware flow control
> > > > ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for
> > > > software flow control
> > > > ModemResultCodesCmd: ATQ0X4 # enable result
> >
> > codes
> >
> > > > #
> > > > ModemMfrQueryCmd: !USR
> > > > ModemModelQueryCmd: ATI3
> > > > ModemRevQueryCmd: ATI7 # XXX returns a
> >
> > multi-line
> >
> > > > result
> > > > #
> > > > # When AT+FCLASS=1 is issued the modem
> >
> > automatically
> >
> > > > switches
> > > > # to software flow control; these parameters let
> >
> > the
> >
> > > > fax software
> > > > # reset flow control as needed after entering
> >
> > Class
> >
> > > > 1.
> > > > #
> > > > Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no
> > > > flow control
> > > > Class1HFLOCmd: AT&H1&I0&R2 # setup modem for
> > > > hardware flow control
> > > > Class1SFLOCmd: "" # modem does this
> >
> > automatically
> >
> > > > #
> > > > # This should resolve "DIS/DTC received 3 times"
> > > > errors:
> > > > #
> > > > Class1ResponseWaitCmd: AT+FRS=1 # wait after
> >
> > sending
> >
> > > > TCF for response
> > > > #
> > > > # The remainder of this configuration is
> >
> > included so
> >
> > > > that the
> > > > # modem "idles" in Class 0 while not sending or
> > > > receiving facsimile.
> > > > #
> > > > ModemSetupAACmd: AT+FCLASS=0 # leave modem
> >
> > idling in
> >
> > > > class 0
> > > > ModemAnswerCmd: AT+FCLASS=1A # answer in Class
> >
> > 1
> >
> > > > #
> > > > # Disables the reporting of bad frames by the
> >
> > modem.
> >
> > > > This
> > > > # overcomes a firmware problem in the x2 and V90
> > > > Sportsters.
> > > > # It is not necessary for the Courier modem.
> > > > #
> > > > Class2NRCmd: AT+FNR=1,1,1,0
> > > >
> > > > probemodem command result is :
> > > >
> > > > This looks like a Class 1 and 2.0 modem.
> > > >
> > > > ATI0 RESULT = "OK" RESPONSE = "3361"
> > > > ATI1 RESULT = "OK" RESPONSE = "966D"
> > > > ATI2 RESULT = "OK" RESPONSE = "OK"
> > > > ATI3 RESULT = "OK" RESPONSE = "USRobotics
> > > > Sportster Voice 33600 Fax Rev.
> > > > 2.0"
> > > > ATI4 RESULT = "OK" RESPONSE = "USRobotics
> > > > Sportster Voice 33600 Fax
> > > > Settings..."
> > > > ATI5 RESULT = "Strike a key when ready . . ."
> > > > RESPONSE = "USRobotics
> > > > Sportster Voice 33600 Fax NVRAM Settings..."
> > > > ATI6 RESULT = "OK" RESPONSE = "USRobotics
> > > > Sportster Voice 33600 Fax Link
> > > > Diagnostics..."
> > > > ATI7 RESULT = "OK" RESPONSE =
> >
> > "Configuration
> >
> > > > Profile..."
> > > > ATI8 RESULT = "OK" RESPONSE = "Blacklist"
> > > > ATI9 RESULT = "OK" RESPONSE =
> > > > "(1.0USR0007\Modem\Sportster 33600
> > > > FAX/VOICE EXT)FF"
> > > >
> > > > Class 1 stuff...
> > > >
> > > > AT+FCLASS=? RESULT = "OK" RESPONSE =
> >
> > "0,1,2.0"
> >
> > > > AT+FCLASS? RESULT = "OK" RESPONSE = "0"
> > > > AT+FCLASS=0 RESULT = "OK" RESPONSE = "OK"
> > > > AT+FCLASS=1 RESULT = "OK" RESPONSE = "OK"
> > > > AT+FCLASS? RESULT = "OK" RESPONSE = "1"
> > > > AT+FJUNK=? RESULT = "ERROR" RESPONSE
> >
> > =
> >
> > > > "ERROR"
> > > > AT+FJUNK? RESULT = "ERROR" RESPONSE
> >
> > =
> >
> > > > "ERROR"
> > > > AT+FAA=? RESULT = "OK" RESPONSE =
> >
> > "(0,1)"
> >
> > > > AT+FAA? RESULT = "OK" RESPONSE = "0"
> > > > AT+FAE=? RESULT = "ERROR" RESPONSE
> >
> > =
> >
> > > > "ERROR"
> > > > AT+FAE? RESULT = "ERROR" RESPONSE =
> >
> > "ERROR"
> >
> > > > AT+FTH=? RESULT = "OK" RESPONSE =
> > > > "3,24,48,72,73,74,96,97,98,121,122,145,146"
> > > > AT+FRH=? RESULT = "OK" RESPONSE =
> > > > "3,24,48,72,73,74,96,97,98,121,122,145,146"
> > > > AT+FTM=? RESULT = "OK" RESPONSE =
> > > > "3,24,48,72,73,74,96,97,98,121,122,145,146"
> > > > AT+FRM=? RESULT = "OK" RESPONSE =
> > > > "3,24,48,72,73,74,96,97,98,121,122,145,146"
> > > > AT+FTS=? RESULT = "ERROR" RESPONSE
> >
> > =
> >
> > > > "ERROR"
> > > > AT+FRS=? RESULT = "ERROR" RESPONSE
> >
> > =
> >
> > > > "ERROR"
> > > > Class 2.0 stuff...
> > > >
> > > > AT+FCLASS=? RESULT = "OK" RESPONSE =
> >
> > "0,1,2.0"
> >
> > > > AT+FCLASS? RESULT = "OK" RESPONSE = "1"
> > > > AT+FCLASS=0 RESULT = "OK" RESPONSE = "OK"
> > > > AT+FCLASS=1 RESULT = "OK" RESPONSE = "OK"
> > > > AT+FCLASS=2.0 RESULT = "OK" RESPONSE = "OK"
> > > > AT+FCLASS? RESULT = "OK" RESPONSE = "1"
> > > > AT+FJU=? RESULT = "ERROR" RESPONSE
> >
> > =
> >
> > > > "ERROR"
> > > > AT+FJU? RESULT = "ERROR" RESPONSE =
> >
> > "ERROR"
> >
> > > > AT+FDR=? RESULT = "" RESPONSE = ""
> > > > AT+FDT=? RESULT = "" RESPONSE = ""
> > > > AT+FIP=? RESULT = "ERROR" RESPONSE
> >
> > =
> >
> > > > "ERROR"
> > > > AT+FAA=? RESULT = "OK" RESPONSE =
> >
> > "(0,1)"
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
