[hylafax-users] Microlink Basic in Class 1

To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] Microlink Basic in Class 1
From: Peter Schaefer <peter.schaefer@xxxxxx>
Date: Fri, 08 Apr 2005 09:08:42 +0200
Hello!

Does anybody run an Elsa Microlink Basic in Class1 successfully?
The past years i run it with Class2.0 without problems; however
recently i wanted to try out the ECM capabilities of Hylafax 4.2.1.

While receiving faxes works without glitch, i get the following
while sending:

Apr 08 08:51:26.97: [26328]: SEND training at v.17 14400 bit/s
Apr 08 08:51:26.97: [26328]: <-- [9:AT+FTH=3\r]
Apr 08 08:51:27.01: [26328]: --> [7:CONNECT]
Apr 08 08:51:27.01: [26328]: <-- data [23]
Apr 08 08:51:27.01: [26328]: <-- data [2]
Apr 08 08:51:28.12: [26328]: --> [7:CONNECT]
Apr 08 08:51:28.12: [26328]: <-- data [7]
Apr 08 08:51:28.12: [26328]: <-- data [2]
Apr 08 08:51:29.24: [26328]: --> [2:OK]
Apr 08 08:51:29.24: [26328]: <-- [9:AT+FTS=7\r]
Apr 08 08:51:29.28: [26328]: --> [5:ERROR]
Apr 08 08:51:29.28: [26328]: MODEM Command error
Apr 08 08:51:29.28: [26328]: Stop and wait failure (modem on hook)
Apr 08 08:51:29.28: [26328]: <-- [9:AT+FTH=3\r]
Apr 08 08:51:29.32: [26328]: --> [7:CONNECT]
Apr 08 08:51:29.32: [26328]: <-- data [3]
Apr 08 08:51:29.32: [26328]: <-- data [2]
Apr 08 08:51:30.73: [26328]: --> [2:OK]
Apr 08 08:51:30.73: [26328]: <-- [4:ATH\r]
Apr 08 08:51:30.87: [26328]: --> [2:OK]
Apr 08 08:51:30.87: [26328]: SESSION END

However, my config.ttyS1 says not to use AT+FTS:

# Configuration parameters for Class 1 interface
#
Class1Cmd:             AT+FCLASS=1     # command to enter class 1
#Class1PPMWaitCmd:      AT+FTS=7        # command to stop and wait before PPM
#Class1TCFWaitCmd:      AT+FTS=7        # command to stop and wait before TCF
#Class1EOPWaitCmd:      AT+FTS=9        # command to stop and wait before EOP
Class1MsgRecvHackCmd:   ""             # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75             # 75ms delay between recv TCF & response
Class1SendMsgDelay:     200            # 200ms delay after training
Class1SwitchingCmd:            AT+FRS=7        # silence between HDLC recv and trans
Class1TrainingRecovery: 1500           # 1.5sec delay after training failure
Class1RecvAbortOK:      200            # wait 200ms for abort response
Class1FrameOverhead:    4              # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:   40000          # 35+5secs waiting for ident frames
Class1TCFMaxNonZero:    10             # max 10% of data may be non-zero
Class1TCFMinRun:        1000            # min run is 2/3rds of TCF duration

Class1SendEOPWaitCmd:  <delay:90>
Class1SendTCFWaitCmd:  <delay:70>
Class1SendPPMWaitCmd:  <delay:70>
AdaptiveAnswer:                yes

Has anybody got Class1 to work with a Microlink Basic?

I include the output of probemodem afterwards (sorry, long!)

Best regards,

 Peter

-- 

Serial port that modem is connected to []? ttyS1

Now we are going to probe the tty port.  This takes a few seconds,
so be patient.  Note that if you do not have the modem cabled to
the port, or the modem is turned off, this may hang (just go and
cable up the modem or turn it on, or whatever).

Probing for best speed to talk to modem: 38400 OK.

This looks like a Class 1, 2, 2.0, 1.0 and 2.1 modem.

ATI0    RESULT = "OK"   RESPONSE = "282"
ATI1    RESULT = "OK"   RESPONSE = "055"
ATI2    RESULT = "OK"   RESPONSE = "OK"
ATI3    RESULT = "OK"   RESPONSE = "Version 1.20 / 26.10.1999"
ATI4    RESULT = "OK"   RESPONSE = "  E1    L2    M0    Q0    V1    X4"
ATI5    RESULT = "OK"   RESPONSE = "OK"
ATI6    RESULT = "OK"   RESPONSE = "MicroLink 56k basic"
ATI7    RESULT = "OK"   RESPONSE = "OK"
ATI8    RESULT = "OK"   RESPONSE = "OK"
ATI9    RESULT = "OK"   RESPONSE = "(#ELS0754-5874\MODEM\MicroLink 56k basic00)"

Class 1 stuff...

AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,1.0,2,2.0,2.1,8,8.0"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "1"
AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=1     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "1"
AT+FJUNK=?      RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FJUNK?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FAA=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FAA? RESULT = "OK"   RESPONSE = "0"
AT+FAE=?        RESULT = "OK"   RESPONSE = "0,1"
AT+FAE? RESULT = "OK"   RESPONSE = "0"
AT+FTH=?        RESULT = "OK"   RESPONSE = "3,24,48,72-74,96-98,121,122,145,146"
AT+FRH=?        RESULT = "OK"   RESPONSE = "3,24,48,72-74,96-98,121,122,145,146"
AT+FTM=?        RESULT = "OK"   RESPONSE = "3,24,48,72-74,96-98,121,122,145,146"
AT+FRM=?        RESULT = "OK"   RESPONSE = "3,24,48,72-74,96-98,121,122,145,146"
AT+FTS=?        RESULT = "OK"   RESPONSE = "0-255"
AT+FRS=?        RESULT = "OK"   RESPONSE = "0-255"

Class 2 stuff...

AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,1.0,2,2.0,2.1,8,8.0"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "1"
AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=1     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=2     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "2"
AT+FJUNK=?      RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FJUNK?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FAA=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FAA? RESULT = "OK"   RESPONSE = "0"
AT+FAXERR=?     RESULT = "OK"   RESPONSE = "(0-255)"
AT+FAXERR?      RESULT = "OK"   RESPONSE = "0"
AT+FBADLIN=?    RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FBADLIN?     RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FBADMUL=?    RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FBADMUL?     RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FBOR=?       RESULT = "OK"   RESPONSE = "(0-3)"
AT+FBOR?        RESULT = "OK"   RESPONSE = "0"
AT+FBUF=?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FBUF?        RESULT = "OK"   RESPONSE = "3072,400,960,768"
AT+FBUG=?       RESULT = "OK"   RESPONSE = "(0-2)"
AT+FBUG?        RESULT = "OK"   RESPONSE = "0"
AT+FCIG=?       RESULT = "OK"   RESPONSE = ""(32-126)""
AT+FCIG?        RESULT = "OK"   RESPONSE = """"
AT+FCQ=?        RESULT = "OK"   RESPONSE = "(0-2),(0-2)"
AT+FCQ? RESULT = "OK"   RESPONSE = "2,2"
AT+FCR=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FCR? RESULT = "OK"   RESPONSE = "1"
AT+FTBC=?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FTBC?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FDCC=?       RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),(0),(0),(0),(0-7)"
AT+FDCC?        RESULT = "OK"   RESPONSE = "0,0,0,0,0,0,0,0"
AT+FDCS=?       RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),(0),(0),(0),(0-7)"
AT+FDCS?        RESULT = "OK"   RESPONSE = "1,5,0,2,0,0,0,0"
AT+FDIS=?       RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),(0),(0),(0),(0-7)"
AT+FDIS?        RESULT = "OK"   RESPONSE = "1,5,0,2,0,0,0,0"
AT+FDT=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FDT? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FECM=?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FECM?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FET=?        RESULT = "OK"   RESPONSE = "0-2,4-6"
AT+FET? RESULT = "OK"   RESPONSE = "0"
AT+FLID=?       RESULT = "OK"   RESPONSE = ""(32-126)""
AT+FLID?        RESULT = "OK"   RESPONSE = ""+49 7326 919206     ""
AT+FLNFC=?      RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FLNFC?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FLPL=?       RESULT = "OK"   RESPONSE = "(0,1)"
AT+FLPL?        RESULT = "OK"   RESPONSE = "0"
AT+FMDL?        RESULT = "OK"   RESPONSE = ""MicroLink 56k basic""
AT+FMFR?        RESULT = "OK"   RESPONSE = ""ELSA AG, Aachen (Germany)""
AT+FMINSP=?     RESULT = "OK"   RESPONSE = "(0-5)"
AT+FMINSP?      RESULT = "OK"   RESPONSE = "0"
AT+FPHCTO=?     RESULT = "OK"   RESPONSE = "(0-255)"
AT+FPHCTO?      RESULT = "OK"   RESPONSE = "50"
AT+FPTS=?       RESULT = "OK"   RESPONSE = "(1-5)"
AT+FPTS?        RESULT = "OK"   RESPONSE = "1"
AT+FRBC=?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FRBC?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FREL=?       RESULT = "OK"   RESPONSE = "(0,1)"
AT+FREL?        RESULT = "OK"   RESPONSE = "0"
AT+FREV?        RESULT = "OK"   RESPONSE = ""Version 1.20 / 26.10.1999""
AT+FSPL=?       RESULT = "OK"   RESPONSE = "(0,1)"
AT+FSPL?        RESULT = "OK"   RESPONSE = "0"
AT+FTBC=?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FTBC?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FVRFC=?      RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FVRFC?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FWDFC=?      RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FWDFC?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FK=? RESULT = "ERROR"        RESPONSE = "ERROR"

Class 2.0 stuff...

AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,1.0,2,2.0,2.1,8,8.0"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "2"
AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=1     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=2.0   RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "2.0"
AT+FJU=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FJU? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FDR=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FDT=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FIP=?        RESULT = "OK"   RESPONSE = "(0)"
AT+FAA=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FAA? RESULT = "OK"   RESPONSE = "0"
AT+FAP=?        RESULT = "OK"   RESPONSE = "(0,1),(0,1),(0,1)"
AT+FAP? RESULT = "OK"   RESPONSE = "0,0,0"
AT+FBS? RESULT = "OK"   RESPONSE = "C0,C0"
AT+FBO=?        RESULT = "OK"   RESPONSE = "(0-3)"
AT+FBO? RESULT = "OK"   RESPONSE = "0"
AT+FBU=?        RESULT = "OK"   RESPONSE = "(0-2)"
AT+FBU? RESULT = "OK"   RESPONSE = "0"
AT+FCC=?        RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),(0),(0),(0),(0-7),(0)"
AT+FCC? RESULT = "OK"   RESPONSE = "0,0,0,0,0,0,0,0,0"
AT+FCQ=?        RESULT = "OK"   RESPONSE = "(0-2),(0-2)"
AT+FCQ? RESULT = "OK"   RESPONSE = "2,2"
AT+FCR=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FCR? RESULT = "OK"   RESPONSE = "1"
AT+FCS=?        RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),(0),(0),(0),(0-7),(0)"
AT+FCS? RESULT = "OK"   RESPONSE = "1,5,0,2,0,0,0,0,0"
AT+FCT=?        RESULT = "OK"   RESPONSE = "(0-FF)"
AT+FCT? RESULT = "OK"   RESPONSE = "5"
AT+FEA=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FEA? RESULT = "OK"   RESPONSE = "0"
AT+FFC=?        RESULT = "OK"   RESPONSE = "(0),(0),(0),(0)"
AT+FFC? RESULT = "OK"   RESPONSE = "0,0,0,0"
AT+FFD=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FFD? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FHS? RESULT = "OK"   RESPONSE = "0"
AT+FIE=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FIE? RESULT = "OK"   RESPONSE = "0"
AT+FIS=?        RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),(0),(0),(0),(0-7),(0)"
AT+FIS? RESULT = "OK"   RESPONSE = "1,5,0,2,0,0,0,0,0"
AT+FIT=?        RESULT = "OK"   RESPONSE = "0-255,0,1"
AT+FIT? RESULT = "OK"   RESPONSE = "0,0"
AT+FLI=?        RESULT = "OK"   RESPONSE = ""(20-7E)""
AT+FLI? RESULT = "OK"   RESPONSE = ""+49 7326 919206     ""
AT+FLO=?        RESULT = "OK"   RESPONSE = "(0-2)"
AT+FLO? RESULT = "OK"   RESPONSE = "1"
AT+FLP=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FLP? RESULT = "OK"   RESPONSE = "0"
AT+FMI? RESULT = "OK"   RESPONSE = ""ELSA AG, Aachen (Germany)""
AT+FMM? RESULT = "OK"   RESPONSE = ""MicroLink 56k basic""
AT+FMR? RESULT = "OK"   RESPONSE = ""Version 1.20 / 26.10.1999""
AT+FMS=?        RESULT = "OK"   RESPONSE = "(0-5)"
AT+FMS? RESULT = "OK"   RESPONSE = "0"
AT+FNR=?        RESULT = "OK"   RESPONSE = "(0,1),(0,1),(0,1),(0,1)"
AT+FNR? RESULT = "OK"   RESPONSE = "1,1,1,0"
AT+FNS=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FNS? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FPA=?        RESULT = "OK"   RESPONSE = ""(20-7E)""
AT+FPA? RESULT = "OK"   RESPONSE = """"
AT+FPI=?        RESULT = "OK"   RESPONSE = ""(20-7E)""
AT+FPI? RESULT = "OK"   RESPONSE = """"
AT+FPP=?        RESULT = "OK"   RESPONSE = "(0)"
AT+FPP? RESULT = "OK"   RESPONSE = "0"
AT+FPR=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FPR? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FPS=?        RESULT = "OK"   RESPONSE = "(1-5)"
AT+FPS? RESULT = "OK"   RESPONSE = "1"
AT+FPW=?        RESULT = "OK"   RESPONSE = ""(20-7E)""
AT+FPW? RESULT = "OK"   RESPONSE = """"
AT+FRQ=?        RESULT = "OK"   RESPONSE = "(0-64),(0-FF)"
AT+FRQ? RESULT = "OK"   RESPONSE = "5F,A"
AT+FRY=?        RESULT = "OK"   RESPONSE = "(0)"
AT+FRY? RESULT = "OK"   RESPONSE = "0"
AT+FSA=?        RESULT = "OK"   RESPONSE = ""(20-7E)""
AT+FSA? RESULT = "OK"   RESPONSE = """"
AT+FSP=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FSP? RESULT = "OK"   RESPONSE = "0"
AT+IFC=?        RESULT = "OK"   RESPONSE = "+IFC: (0-3),(0-2)"
AT+IFC? RESULT = "OK"   RESPONSE = "+IFC: 2,2"
AT+IPR=?        RESULT = "OK"   RESPONSE = "OK"
AT+IPR? RESULT = "OK"   RESPONSE = "+IPR: 0"
AT+FKS=?        RESULT = "ERROR"        RESPONSE = "ERROR"

Class 1.0 stuff...

AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,1.0,2,2.0,2.1,8,8.0"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "2.0"
AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=1.0   RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "1.0"
AT+FJUNK=?      RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FJUNK?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FAA=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FAA? RESULT = "OK"   RESPONSE = "0"
AT+FAE=?        RESULT = "OK"   RESPONSE = "0,1"
AT+FAE? RESULT = "OK"   RESPONSE = "0"
AT+FTH=?        RESULT = "OK"   RESPONSE = "3,24,48,72-74,96-98,121,122,145,146"
AT+FRH=?        RESULT = "OK"   RESPONSE = "3,24,48,72-74,96-98,121,122,145,146"
AT+FTM=?        RESULT = "OK"   RESPONSE = "3,24,48,72-74,96-98,121,122,145,146"
AT+FRM=?        RESULT = "OK"   RESPONSE = "3,24,48,72-74,96-98,121,122,145,146"
AT+FTS=?        RESULT = "OK"   RESPONSE = "0-255"
AT+FRS=?        RESULT = "OK"   RESPONSE = "0-255"
AT+FAR=?        RESULT = "OK"   RESPONSE = "0,1"
AT+FCL=?        RESULT = "OK"   RESPONSE = "0-255"
AT+FIT=?        RESULT = "OK"   RESPONSE = "0-255,0,1"
AT+F34=?        RESULT = "ERROR"        RESPONSE = "ERROR"

Class 2.1 stuff...

AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,1.0,2,2.0,2.1,8,8.0"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "1.0"
AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=1     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=2.1   RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "2.1"
AT+FJU=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FJU? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FDR=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FDT=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FIP=?        RESULT = "OK"   RESPONSE = "(0)"
AT+FAA=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FAA? RESULT = "OK"   RESPONSE = "0"
AT+FAP=?        RESULT = "OK"   RESPONSE = "(0,1),(0,1),(0,1)"
AT+FAP? RESULT = "OK"   RESPONSE = "0,0,0"
AT+FBS? RESULT = "OK"   RESPONSE = "C0,C0"
AT+FBO=?        RESULT = "OK"   RESPONSE = "(0-3)"
AT+FBO? RESULT = "OK"   RESPONSE = "0"
AT+FBU=?        RESULT = "OK"   RESPONSE = "(0-2)"
AT+FBU? RESULT = "OK"   RESPONSE = "0"
AT+FCC=?        RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),(0),(0),(0),(0-7),(0)"
AT+FCC? RESULT = "OK"   RESPONSE = "0,0,0,0,0,0,0,0,0"
AT+FCQ=?        RESULT = "OK"   RESPONSE = "(0-2),(0-2)"
AT+FCQ? RESULT = "OK"   RESPONSE = "2,2"
AT+FCR=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FCR? RESULT = "OK"   RESPONSE = "1"
AT+FCS=?        RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),(0),(0),(0),(0-7),(0)"
AT+FCS? RESULT = "OK"   RESPONSE = "1,5,0,2,0,0,0,0,0"
AT+FCT=?        RESULT = "OK"   RESPONSE = "(0-FF)"
AT+FCT? RESULT = "OK"   RESPONSE = "5"
AT+FEA=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FEA? RESULT = "OK"   RESPONSE = "0"
AT+FFC=?        RESULT = "OK"   RESPONSE = "(0),(0),(0),(0)"
AT+FFC? RESULT = "OK"   RESPONSE = "0,0,0,0"
AT+FFD=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FFD? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FHS? RESULT = "OK"   RESPONSE = "0"
AT+FIE=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FIE? RESULT = "OK"   RESPONSE = "0"
AT+FIS=?        RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),(0),(0),(0),(0-7),(0)"
AT+FIS? RESULT = "OK"   RESPONSE = "1,5,0,2,0,0,0,0,0"
AT+FIT=?        RESULT = "OK"   RESPONSE = "0-255,0,1"
AT+FIT? RESULT = "OK"   RESPONSE = "0,0"
AT+FLI=?        RESULT = "OK"   RESPONSE = ""(20-7E)""
AT+FLI? RESULT = "OK"   RESPONSE = ""+49 7326 919206     ""
AT+FLO=?        RESULT = "OK"   RESPONSE = "(0-2)"
AT+FLO? RESULT = "OK"   RESPONSE = "1"
AT+FLP=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FLP? RESULT = "OK"   RESPONSE = "0"
AT+FMI? RESULT = "OK"   RESPONSE = ""ELSA AG, Aachen (Germany)""
AT+FMM? RESULT = "OK"   RESPONSE = ""MicroLink 56k basic""
AT+FMR? RESULT = "OK"   RESPONSE = ""Version 1.20 / 26.10.1999""
AT+FMS=?        RESULT = "OK"   RESPONSE = "(0-5)"
AT+FMS? RESULT = "OK"   RESPONSE = "0"
AT+FNR=?        RESULT = "OK"   RESPONSE = "(0,1),(0,1),(0,1),(0,1)"
AT+FNR? RESULT = "OK"   RESPONSE = "1,1,1,0"
AT+FNS=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FNS? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FPA=?        RESULT = "OK"   RESPONSE = ""(20-7E)""
AT+FPA? RESULT = "OK"   RESPONSE = """"
AT+FPI=?        RESULT = "OK"   RESPONSE = ""(20-7E)""
AT+FPI? RESULT = "OK"   RESPONSE = """"
AT+FPP=?        RESULT = "OK"   RESPONSE = "(0)"
AT+FPP? RESULT = "OK"   RESPONSE = "0"
AT+FPR=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FPR? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FPS=?        RESULT = "OK"   RESPONSE = "(1-5)"
AT+FPS? RESULT = "OK"   RESPONSE = "1"
AT+FPW=?        RESULT = "OK"   RESPONSE = ""(20-7E)""
AT+FPW? RESULT = "OK"   RESPONSE = """"
AT+FRQ=?        RESULT = "OK"   RESPONSE = "(0-64),(0-FF)"
AT+FRQ? RESULT = "OK"   RESPONSE = "5F,A"
AT+FRY=?        RESULT = "OK"   RESPONSE = "(0)"
AT+FRY? RESULT = "OK"   RESPONSE = "0"
AT+FSA=?        RESULT = "OK"   RESPONSE = ""(20-7E)""
AT+FSA? RESULT = "OK"   RESPONSE = """"
AT+FSP=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FSP? RESULT = "OK"   RESPONSE = "0"
AT+IFC=?        RESULT = "OK"   RESPONSE = "+IFC: (0-3),(0-2)"
AT+IFC? RESULT = "OK"   RESPONSE = "+IFC: 2,2"
AT+IPR=?        RESULT = "OK"   RESPONSE = "OK"
AT+IPR? RESULT = "OK"   RESPONSE = "+IPR: 0"
AT+FKS=?        RESULT = "ERROR"        RESPONSE = "ERROR"



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
Follow-Ups:
- Re: [hylafax-users] Microlink Basic in Class 1
  - From: Lee Howard
Prev by Date: Re: [hylafax-users] Problems receiving fax
Next by Date: [hylafax-users] Windows Printer Driver
Previous by thread: Re: [hylafax-users] Primer mensaje a la lista
Next by thread: Re: [hylafax-users] Microlink Basic in Class 1
Index(es):
- Main
- Thread
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services