[hylafax-users] MultiTech 8 port and Vonage

To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] MultiTech 8 port and Vonage
From: Peter Halliday <hoangelos@xxxxxxxxx>
Reply-to: Peter Halliday <hoangelos@xxxxxxxxx>
Date: Thu, 17 Feb 2005 13:27:18 -0500
I had heard there was a guy on here previously who had done MultiTech
4 port and Vonage.  Was wondering if the guy could help at all (or
anyone else for that matter).  I'm seeing something where the fax
keeps not being able to send the page properly.  Below is the send
session and the configuration of the modem.  I have tried it will all
the classes, and it doesn't seem to matter.  Was there any additional
configuration that you had to do besides the basic?   Are all your
pages coming out correctly?

Peter



[root@silver DBD-mysql-2.9004]# cat /etc/hylafax/log/c000000057
Feb 17 07:19:34.99: [18930]: SESSION BEGIN 000000057 17038154259894
Feb 17 07:19:34.99: [18930]: HylaFAX (tm) Version 4.2.0
Feb 17 07:19:34.99: [18930]: SEND FAX: JOB 58 DEST 8154259894 COMMID
000000057 DEVICE '/dev/ttyS49'
Feb 17 07:19:34.99: [18930]: <-- [9:AT+FLO=1\r]
Feb 17 07:19:35.10: [18930]: --> [2:OK]
Feb 17 07:19:35.10: [18930]: <-- [9:AT+FPP=0\r]
Feb 17 07:19:35.21: [18930]: --> [2:OK]
Feb 17 07:19:35.21: [18930]: <-- [9:AT+FBO=0\r]
Feb 17 07:19:35.32: [18930]: --> [2:OK]
Feb 17 07:19:35.32: [18930]: <-- [10:AT+FCT=30\r]
Feb 17 07:19:35.44: [18930]: --> [2:OK]
Feb 17 07:19:35.44: [18930]: <-- [11:AT+FCQ=1,0\r]
Feb 17 07:19:35.55: [18930]: --> [2:OK]
Feb 17 07:19:35.55: [18930]: <-- [15:AT+FNR=1,1,1,1\r]
Feb 17 07:19:35.66: [18930]: --> [2:OK]
Feb 17 07:19:35.66: [18930]: <-- [13:AT+FAP=1,1,1\r]
Feb 17 07:19:35.78: [18930]: --> [2:OK]
Feb 17 07:19:35.78: [18930]: <-- [9:AT+FIE=0\r]
Feb 17 07:19:35.89: [18930]: --> [2:OK]
Feb 17 07:19:35.89: [18930]: <-- [23:AT+FCC=1,5,2,2,3,1,0,0\r]
Feb 17 07:19:36.01: [18930]: --> [2:OK]
Feb 17 07:19:36.01: [18930]: DIAL 8154259894
Feb 17 07:19:36.01: [18930]: <-- [30:AT+FCC=,,,,,,,,0;DT8154259894\r]
Feb 17 07:19:49.85: [18930]: --> [4:+FCO]
Feb 17 07:19:49.85: [18930]: --> [27:+FCI:"         18154259894"]
Feb 17 07:19:49.85: [18930]: REMOTE CSI "18154259894"
Feb 17 07:19:50.27: [18930]: --> [20:+FIS:1,5,0,2,3,1,0,0]
Feb 17 07:19:50.27: [18930]: --> [2:OK]
Feb 17 07:19:50.27: [18930]: REMOTE best rate 14400 bit/s
Feb 17 07:19:50.27: [18930]: REMOTE max A4 page width (215 mm)
Feb 17 07:19:50.27: [18930]: REMOTE max unlimited page length
Feb 17 07:19:50.27: [18930]: REMOTE best vres 7.7 line/mm
Feb 17 07:19:50.27: [18930]: REMOTE best format 2-D MMR
Feb 17 07:19:50.27: [18930]: REMOTE supports T.30 Annex A, 256-byte ECM
Feb 17 07:19:50.27: [18930]: REMOTE best 0 ms/scanline
Feb 17 07:19:50.27: [18930]: USE 14400 bit/s
Feb 17 07:19:50.27: [18930]: USE 0 ms/scanline
Feb 17 07:19:50.27: [18930]: SEND file "docq/doc58.ps;41"
Feb 17 07:19:50.27: [18930]: USE A4 page width (215 mm)
Feb 17 07:19:50.27: [18930]: USE unlimited page length
Feb 17 07:19:50.27: [18930]: USE 7.7 line/mm
Feb 17 07:19:50.27: [18930]: USE 2-D MR
Feb 17 07:19:50.27: [18930]: <-- [23:AT+FIS=1,5,0,2,1,0,0,0\r]
Feb 17 07:19:50.39: [18930]: --> [2:OK]
Feb 17 07:19:50.39: [18930]: <-- [7:AT+FDT\r]
Feb 17 07:19:57.98: [18930]: --> [20:+FCS:1,5,0,2,1,0,0,0]
Feb 17 07:19:58.09: [18930]: --> [7:CONNECT]
Feb 17 07:19:58.09: [18930]: SEND begin page
Feb 17 07:19:58.09: [18930]: <-- data [1026]
Feb 17 07:19:58.09: [18930]: <-- data [1026]
Feb 17 07:19:58.09: [18930]: <-- data [1035]
Feb 17 07:19:58.09: [18930]: <-- data [1026]
Feb 17 07:20:00.09: [18930]: <-- data [1034]
Feb 17 07:20:00.09: [18930]: <-- data [1030]
Feb 17 07:20:00.09: [18930]: <-- data [1032]
Feb 17 07:20:00.09: [18930]: <-- data [1029]
Feb 17 07:20:02.09: [18930]: <-- data [1035]
Feb 17 07:20:02.09: [18930]: <-- data [1032]
Feb 17 07:20:02.09: [18930]: <-- data [1030]
Feb 17 07:20:02.09: [18930]: <-- data [1029]
Feb 17 07:20:04.09: [18930]: <-- data [1031]
Feb 17 07:20:04.09: [18930]: <-- data [1028]
Feb 17 07:20:04.09: [18930]: <-- data [1030]
Feb 17 07:20:04.09: [18930]: <-- data [1027]
Feb 17 07:20:06.09: [18930]: <-- data [1029]
Feb 17 07:20:06.09: [18930]: <-- data [1031]
Feb 17 07:20:06.09: [18930]: <-- data [1035]
Feb 17 07:20:08.09: [18930]: <-- data [637]
Feb 17 07:20:08.09: [18930]: SENT 20083 bytes of data
Feb 17 07:20:08.09: [18930]: SEND 2D RTC
Feb 17 07:20:08.09: [18930]: <-- data [10]
Feb 17 07:20:08.62: [18930]: SEND end page
Feb 17 07:20:08.62: [18930]: SEND send EOP (no more pages or documents)
Feb 17 07:20:08.62: [18930]: <-- data [2]
Feb 17 07:20:17.50: [18930]: --> [5:ERROR]
Feb 17 07:20:17.50: [18930]: <-- [8:AT+FPS?\r]
Feb 17 07:20:17.62: [18930]: --> [2:02]
Feb 17 07:20:17.62: [18930]: --> [2:OK]
Feb 17 07:20:17.62: [18930]: SEND recv RTN (retrain negative)
Feb 17 07:20:17.62: [18930]: <-- [23:AT+FIS=1,4,0,2,1,0,0,0\r]
Feb 17 07:20:17.74: [18930]: --> [2:OK]
Feb 17 07:20:17.74: [18930]: <-- [7:AT+FDT\r]
Feb 17 07:20:25.36: [18930]: --> [20:+FCS:1,4,0,2,1,0,0,0]
Feb 17 07:20:25.47: [18930]: --> [7:CONNECT]
Feb 17 07:20:25.47: [18930]: SEND begin page
Feb 17 07:20:25.47: [18930]: <-- data [1026]
Feb 17 07:20:25.47: [18930]: <-- data [1026]
Feb 17 07:20:25.47: [18930]: <-- data [1035]
Feb 17 07:20:25.47: [18930]: <-- data [1026]
Feb 17 07:20:27.47: [18930]: <-- data [1034]
Feb 17 07:20:27.47: [18930]: <-- data [1030]
Feb 17 07:20:27.47: [18930]: <-- data [1032]
Feb 17 07:20:27.47: [18930]: <-- data [1029]
Feb 17 07:20:29.47: [18930]: <-- data [1035]
Feb 17 07:20:29.47: [18930]: <-- data [1032]
Feb 17 07:20:29.47: [18930]: <-- data [1030]
Feb 17 07:20:29.47: [18930]: <-- data [1029]
Feb 17 07:20:31.81: [18930]: <-- data [1031]
Feb 17 07:20:31.81: [18930]: <-- data [1028]
Feb 17 07:20:31.81: [18930]: <-- data [1030]
Feb 17 07:20:33.81: [18930]: <-- data [1027]
Feb 17 07:20:33.81: [18930]: <-- data [1029]
Feb 17 07:20:33.81: [18930]: <-- data [1031]
Feb 17 07:20:33.81: [18930]: <-- data [1035]
Feb 17 07:20:35.48: [18930]: <-- data [637]
Feb 17 07:20:35.48: [18930]: SENT 20083 bytes of data
Feb 17 07:20:35.48: [18930]: SEND 2D RTC
Feb 17 07:20:35.48: [18930]: <-- data [10]
Feb 17 07:20:37.55: [18930]: SEND end page
Feb 17 07:20:37.55: [18930]: SEND send EOP (no more pages or documents)
Feb 17 07:20:37.55: [18930]: <-- data [2]
Feb 17 07:20:46.77: [18930]: --> [5:ERROR]
Feb 17 07:20:46.77: [18930]: <-- [8:AT+FPS?\r]
Feb 17 07:20:46.88: [18930]: --> [2:02]
Feb 17 07:20:46.88: [18930]: --> [2:OK]
Feb 17 07:20:46.88: [18930]: SEND recv RTN (retrain negative)
Feb 17 07:20:46.88: [18930]: <-- [23:AT+FIS=1,3,0,2,1,0,0,0\r]
Feb 17 07:20:47.00: [18930]: --> [2:OK]
Feb 17 07:20:47.00: [18930]: <-- [7:AT+FDT\r]
Feb 17 07:21:15.82: [18930]: --> [20:+FCS:1,0,0,2,1,0,0,0]
Feb 17 07:21:15.93: [18930]: --> [7:CONNECT]
Feb 17 07:21:15.93: [18930]: SEND begin page
Feb 17 07:21:15.93: [18930]: <-- data [1026]
Feb 17 07:21:15.93: [18930]: <-- data [1026]
Feb 17 07:21:15.93: [18930]: <-- data [1035]
Feb 17 07:21:15.93: [18930]: <-- data [1026]
Feb 17 07:21:20.61: [18930]: <-- data [1034]
Feb 17 07:21:20.61: [18930]: <-- data [1030]
Feb 17 07:21:20.61: [18930]: <-- data [1032]
Feb 17 07:21:25.46: [18930]: <-- data [1029]
Feb 17 07:21:30.31: [18930]: <-- data [1035]
Feb 17 07:21:30.31: [18930]: <-- data [1032]
Feb 17 07:21:35.11: [18930]: <-- data [1030]
Feb 17 07:21:39.49: [18930]: <-- data [1029]
Feb 17 07:21:39.49: [18930]: <-- data [1031]
Feb 17 07:21:44.39: [18930]: <-- data [1028]
Feb 17 07:21:49.25: [18930]: <-- data [1030]
Feb 17 07:21:54.00: [18930]: <-- data [1027]
Feb 17 07:21:54.00: [18930]: <-- data [1029]
Feb 17 07:21:58.84: [18930]: <-- data [1031]
Feb 17 07:22:03.65: [18930]: <-- data [1035]
Feb 17 07:22:03.65: [18930]: <-- data [637]
Feb 17 07:22:08.29: [18930]: SENT 20083 bytes of data
Feb 17 07:22:08.29: [18930]: SEND 2D RTC
Feb 17 07:22:08.29: [18930]: <-- data [10]
Feb 17 07:22:18.08: [18930]: SEND end page
Feb 17 07:22:18.08: [18930]: SEND send EOP (no more pages or documents)
Feb 17 07:22:18.08: [18930]: <-- data [2]
Feb 17 07:22:27.64: [18930]: --> [6:+FHS:0]
Feb 17 07:22:27.64: [18930]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Feb 17 07:22:27.64: [18930]: SEND recv MCF (message confirmation)
Feb 17 07:22:27.64: [18930]: SEND FAX (000000057): FROM
root@xxxxxxxxxxxxxxxx TO 8154259894 (page 1 of 1 sent in 2:37)
Feb 17 07:22:27.64: [18930]: SEND FAX (000000057): FROM
root@xxxxxxxxxxxxxxxx TO 8154259894 (docq/doc58.ps;41 sent in 2:37)
Feb 17 07:22:27.64: [18930]: <-- [5:ATH0\r]
Feb 17 07:22:27.88: [18930]: --> [2:OK]
Feb 17 07:22:27.88: [18930]: SESSION END



[root@silver DBD-mysql-2.9004]# cat /etc/hylafax/etc/config.ttyS49
# $Id: lucent-mt-20,v 1.13 2004/06/01 21:34:39 lhoward Exp $
#
# prototype config file for MultiTech MT5634ZBA-V.92-NAM
#

#
#
CountryCode:            1
AreaCode:               703
FAXNumber:              +1.999.555.1212
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "NothingSetup"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#
#

ModemType:              Class2.0
ModemRate:              19200
ModemNoFlowCmd:         AT&K0
ModemSoftFlowCmd:       AT&K4
ModemHardFlowCmd:       AT&K3

Class2APCmd:            AT+FAP=1,1,1
Class2BUGCmd:           AT+FBU=0                # early firmware is buggy
Class2SendRTC:          yes
Class2UseHex:           yes

# Some firmwares do not report copy quality correction, although it
# is present and cannot be disabled.  Thus modem-based CQ must be used.
Class2CQQueryCmd:       "!(00-02),(00-02)"
Class2CQCmd:            AT+FCQ=1,0

# versions that respond to AT+FFC=? with non-zero data support RTFCC
# Class2RTFCC:          yes

# unfortunately, HylaFAX can't currently send or receive in color
ModemAnswerCmd:         AT+FCC=,,,,,,,,0;A
ModemDialCmd:           AT+FCC=,,,,,,,,0;DT%s

# Some firmware revisions (i.e. 1.25 in ZBAs) report MMR support but
# corrupt the data.  Enabling the following lines should work around this.
# Compare this against the modem's AT+FCC=? response.
# Class2DCCQueryCmd:   
"!(00-01),(00-05),(00-02),(00-02),(00-01),(00-01),(00),(00-07)"
# ModemAnswerCmd:       AT+FCC=,,,,1,,,,0;A
# ModemDialCmd:         AT+FCC=,,,,1,,,,0;DT%s

# If your modem supports ECM you may want to do something like this
# Class2Cmd:            AT+FCLASS=2.0;+FRY=4

# If your line supports Caller-ID, you may want to uncomment this...
# QualifyCID:           etc/cid         # you must create this file
# ModemResetCmds:       AT+VCID=1
# CIDNumber:            "NMBR="
# CIDName:              "NAME="

# Or with the MT5634ZBA-DID you'll probably need something like...
# ModemReadyCmds:       AT*DS1*DD0*DF1*DN4      # enable DTMF-DID,
wink-start, 4 digits
# CIDNumber:            "DTMF"          # format of AT*DF1
# CIDNumberAnswerLength:        4       # four DTMF-DID digits then ATA

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
Follow-Ups:
- Re: [hylafax-users] MultiTech 8 port and Vonage
  - From: Lee Howard
Prev by Date: Re: [hylafax-users] Newbie: "530 Login incorrect" Problem
Next by Date: Re: [hylafax-users] MultiTech 8 port and Vonage
Previous by thread: Re: [hylafax-users] Faxmail + notify (solved, now on to modifying the notify script)
Next by thread: Re: [hylafax-users] MultiTech 8 port and Vonage
Index(es):
- Main
- Thread
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services