[hylafax-users] 4.2.1 Job Batching with MultiTech MT2834ZDX Modems

To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] 4.2.1 Job Batching with MultiTech MT2834ZDX Modems
From: Michael Boers <msb@xxxxxxxxxxxxxxx>
Date: Wed, 26 Jan 2005 10:35:59 -0500

After recently upgrading to hylafax 4.2.1 I began receiving notices of squished faxes. It turns out when jobs are batched and sent with my MultiTech MT2834ZDX modem the following happens:

1. The first job is sent normally 2. The rest of the jobs are sent in fine (7.7 line/mm) mode 3. Because the fax is imaged in normal (3.85 line/mm) mode, it only uses half of the page vertically hence is squished

Questions: 1. Is there a way to disable job batching globally rather than on a per destination basis? 2. Is there a fix for this?

Partial Log File Follows, notice how the FDCS parameters from the receiving machine at time 09:38:48.53 and 09:39:17.66 are different.

Jan 26 09:38:19.89: [67876]: SESSION BEGIN 000001867 16165740493 Jan 26 09:38:19.89: [67876]: HylaFAX (tm) Version 4.2.1 Jan 26 09:38:19.89: [67876]: SEND FAX: JOB 811 DEST 5740493 COMMID 000001867 DEVICE '/dev/cuac02' Jan 26 09:38:19.89: [67876]: <-- [10:AT+FTBC=0\r] Jan 26 09:38:20.15: [67876]: --> [2:OK] Jan 26 09:38:20.15: [67876]: <-- [10:AT+FBOR=0\r] Jan 26 09:38:20.41: [67876]: --> [2:OK] Jan 26 09:38:20.41: [67876]: <-- [13:AT+FPHCTO=30\r] Jan 26 09:38:20.67: [67876]: --> [2:OK] Jan 26 09:38:20.67: [67876]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r] Jan 26 09:38:20.94: [67876]: --> [2:OK] Jan 26 09:38:20.94: [67876]: DIAL 5740493 Jan 26 09:38:20.94: [67876]: <-- [12:ATDT5740493\r] Jan 26 09:38:38.10: [67876]: --> [5:+FCON] Jan 26 09:38:41.21: [67876]: --> [42:+FNSF:00 00 25 01 50 4D 4F 43 41 54 41 44 ] Jan 26 09:38:41.21: [67876]: REMOTE NSF "00 00 25 01 50 4D 4F 43 41 54 41 44" Jan 26 09:38:41.21: [67876]: NSF remote fax equipment: Ricoh Jan 26 09:38:41.21: [67876]: NSF remote station ID: "DATACOMP" Jan 26 09:38:41.21: [67876]: --> [28:+FCSI:" 800 841 8062"] Jan 26 09:38:41.21: [67876]: REMOTE CSI "800 841 8062" Jan 26 09:38:41.21: [67876]: --> [21:+FDIS:1,5,0,2,1,2,0,2] Jan 26 09:38:41.21: [67876]: --> [2:OK] Jan 26 09:38:41.21: [67876]: REMOTE best rate 14400 bit/s Jan 26 09:38:41.21: [67876]: REMOTE max A4 page width (215 mm) Jan 26 09:38:41.21: [67876]: REMOTE max unlimited page length Jan 26 09:38:41.21: [67876]: REMOTE best vres 7.7 line/mm Jan 26 09:38:41.21: [67876]: REMOTE best format 2-D MR Jan 26 09:38:41.21: [67876]: REMOTE supports T.30 Annex A, 256-byte ECM Jan 26 09:38:41.21: [67876]: REMOTE best 10 ms, 5 ms/scanline Jan 26 09:38:41.21: [67876]: USE 14400 bit/s Jan 26 09:38:41.21: [67876]: USE 10 ms, 5 ms/scanline Jan 26 09:38:41.21: [67876]: SEND file "docq/doc26750.ps;70" Jan 26 09:38:41.21: [67876]: USE A4 page width (215 mm) Jan 26 09:38:41.21: [67876]: USE unlimited page length Jan 26 09:38:41.21: [67876]: USE 3.85 line/mm Jan 26 09:38:41.21: [67876]: USE 2-D MR Jan 26 09:38:41.21: [67876]: <-- [24:AT+FDIS=0,5,0,2,1,0,0,2\r] Jan 26 09:38:41.48: [67876]: --> [2:OK] Jan 26 09:38:41.48: [67876]: <-- [7:AT+FDT\r] Jan 26 09:38:48.53: [67876]: --> [21:+FDCS:0,5,0,2,1,0,0,3] Jan 26 09:38:48.53: [67876]: --> [7:CONNECT] Jan 26 09:38:48.53: [67876]: SEND wait for XON Jan 26 09:38:48.53: [67876]: --> [1:^Q] Jan 26 09:38:48.53: [67876]: SEND begin page Jan 26 09:38:48.53: [67876]: <-- data [1029] Jan 26 09:38:48.53: [67876]: <-- data [1039] Jan 26 09:38:48.53: [67876]: <-- data [1034] Jan 26 09:38:48.53: [67876]: <-- data [1036] Jan 26 09:38:48.53: [67876]: <-- data [1034] Jan 26 09:38:49.52: [67876]: <-- data [1040] Jan 26 09:38:49.52: [67876]: <-- data [1036] Jan 26 09:38:49.52: [67876]: <-- data [1029] Jan 26 09:38:49.52: [67876]: <-- data [1035] Jan 26 09:38:54.32: [67876]: <-- data [1039] Jan 26 09:38:54.32: [67876]: <-- data [1035] Jan 26 09:38:54.32: [67876]: <-- data [1031] Jan 26 09:38:54.32: [67876]: <-- data [1034] Jan 26 09:38:57.29: [67876]: <-- data [1043] Jan 26 09:38:57.29: [67876]: <-- data [1043] Jan 26 09:38:57.29: [67876]: <-- data [1035] Jan 26 09:38:57.29: [67876]: <-- data [1033] Jan 26 09:38:59.97: [67876]: <-- data [1030] Jan 26 09:38:59.97: [67876]: <-- data [1029] Jan 26 09:38:59.97: [67876]: <-- data [1033] Jan 26 09:38:59.97: [67876]: <-- data [894] Jan 26 09:39:02.92: [67876]: SENT 21368 bytes of data Jan 26 09:39:02.92: [67876]: <-- data [2] Jan 26 09:39:02.92: [67876]: SEND end page Jan 26 09:39:05.29: [67876]: --> [38: ^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q^S^Q ^S^Q] Jan 26 09:39:05.29: [67876]: --> [2:OK] Jan 26 09:39:05.29: [67876]: SEND send EOM (more documents) Jan 26 09:39:05.29: [67876]: <-- [9:AT+FET=1\r] Jan 26 09:39:09.83: [67876]: --> [7:+FPTS:1] Jan 26 09:39:09.83: [67876]: --> [2:OK] Jan 26 09:39:09.83: [67876]: SEND recv MCF (message confirmation) Jan 26 09:39:09.83: [67876]: SEND FAX (000001867): FROM root@xxxxxxxxxxxxxxxxxxxxxxxxxxx TO 5740493 (docq/doc26750.ps;70 sent in 0:28) Jan 26 09:39:09.84: [67876]: SEND FAX (000001867): FROM root@xxxxxxxxxxxxxxxxxxxxxxxxxxx TO 5740493 (page 1 of 1 sent in 0:28) Jan 26 09:39:10.85: [67876]: SEND FAX: JOB 810 DEST 5740493 COMMID 000001867 DEVICE '/dev/cuac02' Jan 26 09:39:10.85: [67876]: REMOTE best rate 14400 bit/s Jan 26 09:39:10.85: [67876]: REMOTE max A4 page width (215 mm) Jan 26 09:39:10.85: [67876]: REMOTE max unlimited page length Jan 26 09:39:10.85: [67876]: REMOTE best vres 7.7 line/mm Jan 26 09:39:10.85: [67876]: REMOTE best format 2-D MR Jan 26 09:39:10.85: [67876]: REMOTE supports T.30 Annex A, 256-byte ECM Jan 26 09:39:10.85: [67876]: REMOTE best 10 ms, 5 ms/scanline Jan 26 09:39:10.85: [67876]: USE 14400 bit/s Jan 26 09:39:10.85: [67876]: USE 10 ms, 5 ms/scanline Jan 26 09:39:10.85: [67876]: SEND file "docq/doc26749.ps;70" Jan 26 09:39:10.85: [67876]: USE A4 page width (215 mm) Jan 26 09:39:10.85: [67876]: USE unlimited page length Jan 26 09:39:10.85: [67876]: USE 3.85 line/mm Jan 26 09:39:10.85: [67876]: USE 2-D MR Jan 26 09:39:10.85: [67876]: <-- [7:AT+FDT\r] Jan 26 09:39:17.66: [67876]: --> [21:+FDCS:1,5,0,2,1,0,0,1] Jan 26 09:39:17.66: [67876]: --> [7:CONNECT] Jan 26 09:39:17.66: [67876]: SEND wait for XON Jan 26 09:39:17.66: [67876]: --> [1:^Q]


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Follow-Ups:
- Re: [hylafax-users] 4.2.1 Job Batching with MultiTech MT2834ZDX Modems
  - From: Lee Howard
- Re: [hylafax-users] 4.2.1 Job Batching with MultiTech MT2834ZDX Modems
  - From: Lee Howard

Prev by Date: [hylafax-users] fax server web administration interface
Next by Date: Re: [hylafax-users] Failure to train remote modem at 2400 ...
Previous by thread: Re: [hylafax-users] fax server web administration interface
Next by thread: Re: [hylafax-users] 4.2.1 Job Batching with MultiTech MT2834ZDX Modems
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services