[hylafax-users] Hylafax 4.2.0 under debian sarge MODEM: Longshine LCS-8560VA-A

[Klaus Haberkorn <hk@xxxxxxxxx>]

After some days struggle with the deb-package
I built hylafax from sources and everything ran
much better.
The installation looks good, but I cannot receive
any fax properly, heres the log:

Dec 24 21:05:35 tunix FaxQueuer[13607]: HylaFAX (tm) Version 4.2.0
Dec 24 21:05:35 tunix FaxQueuer[13607]: Copyright (c) 1990-1996 Sam Leffler
Dec 24 21:05:35 tunix FaxQueuer[13607]: Copyright (c) 1991-1996 Silicon 
Graphics, Inc.
Dec 24 21:05:44 tunix FaxGetty[13585]: MODEM INTEL CORPORATION MD56xx/CD08.55 
- 747 SERIAL
Dec 24 21:05:44 tunix FaxGetty[13585]: HELLO
Dec 24 21:05:50 tunix FaxGetty[13585]: ANSWER: FAX CONNECTION  DEVICE 
'/dev/ttyS0'
Dec 24 21:06:32 tunix FaxGetty[13585]: RECV FAX (000000011): from +49...., 
page 1 in 0:33, INF, 3.85 line/mm, 2-D MMR, 14400 bit/s
Dec 24 21:06:32 tunix FaxGetty[13585]: RECV FAX (000000011): 
recvq/fax000000011.tif from +49...., route to <unspecified>, 1 pages in 0:42
Dec 24 21:06:32 tunix FaxGetty[13585]: RECV FAX (000000011): session with 
+49.... terminated abnormally: Failure to receive silence.
Dec 24 21:06:32 tunix FaxGetty[13585]: RECV FAX: bin/faxrcvd 
"recvq/fax000000011.tif" "ttyS0" "000000011" "Failure to receive silence." "" 
""
Dec 24 21:06:46 tunix FaxGetty[13585]: MODEM INTEL CORPORATION MD56xx/CD08.55 
- 747 SERIAL

I found some newsgroups threads in Google, which pointed to
the modem commands: AT+FTS and AT+FRS
So I startet to play with these values, but it didnt helped anyway,
heres my current config.ttyS0:

CountryCode:  49
AreaCode:  {MyAreaCode}
FAXNumber:  {MyFaxNumber}
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing:  1
SessionTracing:  11
RecvFileMode:  0600
LogFileMode:  0600
DeviceMode:  0600
RingsBeforeAnswer: 1
SpeakerVolume:  off
GettyArgs:  "-h %l dx_%s"
LocalIdentifier: "{MyIdString}"
LogFacility:  local4
TagLineFont:  etc/lutRS18.pcf
TagLineFormat:  "Von %%l|%c|Seite %%P von %%T"
### QualifyTSI:  etc/hosts.hfaxd
MaxRecvPages:  25
### (following has been copied from config/cirrus:
ModemType:  Class1  # use this to supply a hint
ModemRate:  57600  # rate for DCE-DTE communication
ModemFlowControl: rtscts  # RTS/CTS flow control assumed
#
ModemSoftFlowCmd: AT\Q1  # set desired flow control method
ModemHardFlowCmd: AT\Q3  # set desired flow control method
ModemSetupDTRCmd: AT&D3  # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1  # setup so DCD follows carrier
ModemDialCmd:  ATDT%s
#
# Happy days!  This modem has proper support for querying
# the model, manufacturer, and firmware revision!
#
ModemMfrQueryCmd: AT+FMFR?
ModemModelQueryCmd: AT+FMDL?
ModemRevQueryCmd: AT+FREV?
#
### (the first 3 have been set to values 7..9 before)
Class1PPMWaitCmd: AT+FTS=0  # command to stop and wait before PPM
Class1TCFWaitCmd: AT+FTS=0  # command to stop and wait before TCF
Class1EOPWaitCmd: AT+FTS=0  # command to stop and wait before EOP
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans

Can anybody help?

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*