|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Errore no answer T.30 T1 Timeout
Non riesco a mandare i fax con il modem MultiTech 2834ZDX, forse sbaglio
qualcosa sulla configurazione.
Se qualcuno ha qualche idea ringrazio anticipatamente.
Massimo
email: pilia@xxxxxxxxxxx
File: config.ttyS1:
# $Id: mt-1432,v 1.2 2002/04/07 20:29:26 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names
of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for a Multi-Tech MT1432, MT224BA, and MT1932ZDX modems.
#
# MT1432 firmware rev 0307 I or newer
# MT132BG rev 0109A
# MT1932ZDX rev 0109H
#
# Note that MT1432 modems come in several varieties:
#
# MT1432BA uses Rockwell data pump
# MT1432BA/A uses AT&T data pump
# MT1432BG MT1432BA tweaked for German FCC
# MT1432MK (for UK?)
#
# The modem has been tried with both XON/XOFF and RTS/CTS flow
# control; this configuration is for hardware flow control.
#
#
CountryCode: 39
AreaCode: 075
FAXNumber: +39.075.8009203
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0664
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: on
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Nome Ditta"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use class 2 interface
ModemRate: 19200 # lock rate for DCE-DTE
communication
ModemFlowControl: rtscts # default
#
ModemHardFlowCmd: AT&E4 # hardware flow control
ModemSoftFlowCmd: AT&E5 # software flow control
ModemSetupDTRCmd: AT&D3 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or
not)
ModemSetupAACmd: AT+FAA=1 # enable adaptive-answer in class 2
#
# NB: some models get confused by @ in ModemDialCmd
#
ModemDialCmd: ATDT0%s
#
Class2RecvDataTrigger: "\022" # character sent to modem to start
recv
File di log dell' errore:
Dec 02 08:42:59.40: [ 1949]: SESSION BEGIN 00000004 39
Dec 02 08:42:59.40: [ 1949]: HylaFAX (tm) Version 4.1.5
Dec 02 08:42:59.40: [ 1949]: SEND FAX: JOB 2 DEST 1 COMMID 00000004 DEVICE
'/dev/ttyS1'
Dec 02 08:42:59.40: [ 1949]: DELAY 75 ms
Dec 02 08:42:59.48: [ 1949]: DELAY 2600 ms
Dec 02 08:43:02.08: [ 1949]: DELAY 10 ms
Dec 02 08:43:02.09: [ 1949]: <-- [4:ATZ\r]
Dec 02 08:43:02.70: [ 1949]: --> [3:ATZ]
Dec 02 08:43:02.70: [ 1949]: --> [2:OK]
Dec 02 08:43:02.70: [ 1949]: DELAY 3000 ms
Dec 02 08:43:05.70: [ 1949]: <-- [5:ATE0\r]
Dec 02 08:43:05.91: [ 1949]: --> [4:ATE0]
Dec 02 08:43:05.91: [ 1949]: --> [2:OK]
Dec 02 08:43:05.91: [ 1949]: <-- [5:ATV1\r]
Dec 02 08:43:06.12: [ 1949]: --> [2:OK]
Dec 02 08:43:06.12: [ 1949]: <-- [5:ATQ0\r]
Dec 02 08:43:06.33: [ 1949]: --> [2:OK]
Dec 02 08:43:06.33: [ 1949]: <-- [7:ATS0=0\r]
Dec 02 08:43:06.55: [ 1949]: --> [2:OK]
Dec 02 08:43:06.55: [ 1949]: <-- [7:ATS8=2\r]
Dec 02 08:43:06.77: [ 1949]: --> [2:OK]
Dec 02 08:43:06.77: [ 1949]: <-- [8:ATS7=60\r]
Dec 02 08:43:06.99: [ 1949]: --> [2:OK]
Dec 02 08:43:06.99: [ 1949]: <-- [6:AT&E4\r]
Dec 02 08:43:07.21: [ 1949]: --> [2:OK]
Dec 02 08:43:07.21: [ 1949]: <-- [6:AT&D3\r]
Dec 02 08:43:07.43: [ 1949]: --> [2:OK]
Dec 02 08:43:07.43: [ 1949]: <-- [6:AT&C1\r]
Dec 02 08:43:07.65: [ 1949]: --> [2:OK]
Dec 02 08:43:07.65: [ 1949]: <-- [12:AT+FCLASS=2\r]
Dec 02 08:43:07.87: [ 1949]: --> [2:OK]
Dec 02 08:43:07.87: [ 1949]: <-- [10:AT+FTBC=0\r]
Dec 02 08:43:08.09: [ 1949]: --> [2:OK]
Dec 02 08:43:08.09: [ 1949]: <-- [10:AT+FBOR=0\r]
Dec 02 08:43:08.31: [ 1949]: --> [2:OK]
Dec 02 08:43:08.31: [ 1949]: <-- [13:AT+FPHCTO=30\r]
Dec 02 08:43:08.53: [ 1949]: --> [2:OK]
Dec 02 08:43:08.53: [ 1949]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Dec 02 08:43:08.76: [ 1949]: --> [2:OK]
Dec 02 08:43:08.76: [ 1949]: <-- [7:ATL0M1\r]
Dec 02 08:43:08.98: [ 1949]: --> [2:OK]
Dec 02 08:43:08.98: [ 1949]: <-- [12:AT+FCLASS=2\r]
Dec 02 08:43:09.30: [ 1949]: --> [2:OK]
Dec 02 08:43:09.30: [ 1949]: <-- [10:AT+FTBC=0\r]
Dec 02 08:43:09.62: [ 1949]: --> [2:OK]
Dec 02 08:43:09.62: [ 1949]: <-- [10:AT+FBOR=0\r]
Dec 02 08:43:09.94: [ 1949]: --> [2:OK]
Dec 02 08:43:09.94: [ 1949]: <-- [13:AT+FPHCTO=30\r]
Dec 02 08:43:10.26: [ 1949]: --> [2:OK]
Dec 02 08:43:10.26: [ 1949]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Dec 02 08:43:10.59: [ 1949]: --> [2:OK]
Dec 02 08:43:10.59: [ 1949]: <-- [27:AT+FLID="Petrini 1822 SpA"\r]
Dec 02 08:43:10.92: [ 1949]: --> [2:OK]
Dec 02 08:43:10.92: [ 1949]: DIAL 1
Dec 02 08:43:10.92: [ 1949]: <-- [7:ATDT01\r]
Dec 02 08:44:54.11: [ 1949]: --> [8:+FHNG:11]
Dec 02 08:44:54.11: [ 1949]: REMOTE HANGUP: No answer (T.30 T1 timeout)
(code 11)
Dec 02 08:44:54.11: [ 1949]: SEND FAILED: JOB 2 DEST 1 ERR No answer (T.30
T1 timeout)
Dec 02 08:44:54.11: [ 1949]: SEND FAILED: JOB 2 DEST 1 ERR No answer (T.30
T1 timeout); too many attempts to dial
Dec 02 08:44:54.11: [ 1949]: <-- [5:ATH0\r]
Dec 02 08:44:54.78: [ 1949]: --> [2:OK]
Dec 02 08:44:54.78: [ 1949]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
