Re: [hylafax-users] Problems with hylafax 4.2.0-1 and a zyxel u90e 1.13

[nick <nick@xxxxxxxxxx>]

nick wrote:

> The problem is that faxgetty hangs.
> The system is a redhat based distribution (e-smith 5.0   2.2.19-7.0.8 
> kernel).
>
> Before I upgraded to 4.2 it was a 4.1.3 distrib, and would hang on 
> almost any incoming fax (two would work, the third would stop after  
> ANSWER: FAX CONNECTION. This only started occuring after I upgraded to 
> the ZyXEL U90Es, beforehand it would block occasionaly.
>
> It still does so, much less frequently, now it hangs every 20 faxes or 
> so after stating ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS1' .  After 
> that, nothing, no more messages are produced. I usually restart 
> hylafax after 4 minutes without any new messages, (thank you for 
> allowing the restarting of faxgetty with this command, it was annoying 
> to have to kill -9 the PID). I can't tell much about what causes the 
> process to hang, the redhat rpm doesn't seem to have logging enabled, 
> or if it does, I can't find the logs.... (they're not in 
> /var/spool/hylafax/logs)
>
> Has anyone experienced this problem, I'll gladly supply any 
> information I can to help me avoid this situation.
>
> P.S. The machine and software are soon to be upgraded, but I'd like to 
> be sure this problem doesn't tag along, if at all possible.
>
> Nick
>
>
> ____________________ HylaFAX(tm) Users Mailing List 
> _______________________
>  To subscribe/unsubscribe, click 
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < 
> /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*


As a followup to my post, here's a log of one of the failed sesions:

Sep 02 10:11:24.33: [ 5443]: SESSION BEGIN 00042873 39----899955 (for a 
little security)
Sep 02 10:11:24.33: [ 5443]: <-- [4:ATA\r]
Sep 02 10:11:33.89: [ 5443]: --> [4:+FCO]
Sep 02 10:11:33.89: [ 5443]: ANSWER: FAX CONNECTION
Sep 02 10:11:33.89: [ 5443]: RECV FAX: begin
Sep 02 10:11:34.17: [ 5443]: --> [27:+FTI:"       +41 971 64 43"]
Sep 02 10:11:34.17: [ 5443]: REMOTE TSI "+41 971 64 43"
Sep 02 10:11:34.17: [ 5443]: --> [20:+FCS:0,5,0,2,1,0,0,1]
Sep 02 10:11:34.17: [ 5443]: REMOTE wants 14400 bit/s
Sep 02 10:11:34.17: [ 5443]: REMOTE wants page width 1728 pixels in 215 mm
Sep 02 10:11:34.17: [ 5443]: REMOTE wants unlimited page length
Sep 02 10:11:34.17: [ 5443]: REMOTE wants 3.85 line/mm
Sep 02 10:11:34.17: [ 5443]: REMOTE wants 2-D MR
Sep 02 10:11:34.17: [ 5443]: --> [2:OK]
Sep 02 10:11:34.17: [ 5443]: <-- [7:AT+FDR\r]
Sep 02 10:11:39.52: [ 5443]: --> [20:+FCS:0,5,0,2,1,0,0,1]
Sep 02 10:11:39.52: [ 5443]: REMOTE wants 14400 bit/s
Sep 02 10:11:39.52: [ 5443]: REMOTE wants page width 1728 pixels in 215 mm
Sep 02 10:11:39.52: [ 5443]: REMOTE wants unlimited page length
Sep 02 10:11:39.52: [ 5443]: REMOTE wants 3.85 line/mm
Sep 02 10:11:39.52: [ 5443]: REMOTE wants 2-D MR
Sep 02 10:11:39.52: [ 5443]: --> [7:CONNECT]
Sep 02 10:11:39.52: [ 5443]: RECV: begin page
Sep 02 10:11:39.52: [ 5443]: RECV: send trigger 022
Sep 02 10:11:39.52: [ 5443]: <-- data [1]
Sep 02 10:11:55.39: [ 5443]: RECV: 28372 bytes of data, 1128 total lines
Sep 02 10:23:02.88: [ 5443]: CLOSE /dev/ttyS1   <------- this is me 
restarting hylafax.

Again, I have an esmith server, it should be based up redhat 7.x kernel  
2.2.19-7.0.8, no gcc (I used your compiled package hylafax-4.2.0-1rh7).

The modem is a zyxel U90E, firmware 1.13, configured with the default 
2.0 settings.

Any suggestions are welcome...

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*