Re: [hylafax-users] Err No carrier detected.

I forgot to add that the HylaFax version is 4.1.7

Also I add the modem config file below

I am open to any suggestions.

# Configuration for using the Class 1 command interface with

# a USR Courier or Sportster modem and XON/XOFF flow control.

CountryCode: 1

AreaCode: 713

FAXNumber: +1 713 xxx-xxxx

LongDistancePrefix: 1

InternationalPrefix: 11

DialStringRules: etc/dialrules

ServerTracing: 1

SessionTracing: 0xffffffff

RecvFileMode: 644

LogFileMode: 644

DeviceMode: 666

RingsBeforeAnswer: 2

SpeakerVolume: off

GettyArgs: -h %l dx_%s

LocalIdentifier: APS-Houston-Pharmacy

TagLineFont: etc/lutRS18.pcf

TagLineFormat: From %%l|%c|Page %%P of %%T

MaxRecvPages: 25

# Modem-related stuff: should reflect modem command interface

# and hardware connection/cabling (e.g. flow control).

ModemType: Class1 # use class 1 interface

ModemRate: 19200 # rate for DCE-DTE communication

ModemFlowControl: xonxoff # software flow control

ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem

ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)

ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control

ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control

ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control

ModemResultCodesCmd: ATQ0X4 # enable result codes

ModemMfrQueryCmd: !USR

ModemModelQueryCmd: ATI3

ModemRevQueryCmd: ATI7 # XXX returns a multi-line result

# When AT+FCLASS=1 is issued the modem automatically switches

# to software flow control; these parameters let the fax software

# reset flow control as needed after entering Class 1.

Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no flow control

Class1HFLOCmd: AT&H1&I0&R2 # setup modem for hardware flow control

Class1SFLOCmd: # modem does this automatically

"# This should resolve ""DIS/DTC received 3 times"" errors:"

Class1ResponseWaitCmd: AT+FRS=1 # wait after sending TCF for response

# The remainder of this configuration is included so that the

"# modem ""idles"" in Class 0 while not sending or receiving facsimile."

ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0

ModemAnswerCmd: AT+FCLASS=1A # answer in Class 1

# Disables the reporting of bad frames by the modem. This

# overcomes a firmware problem in the x2 and V90 Sportsters.

# It is not necessary for the Courier modem.

"Class2NRCmd: AT+FNR=1,1,1,0"

#Caller Id Support

ModemResetCmds: AT#CID=1

CIDName: “NAME =”

CIDNumber: “NMBR =”

Thanks

From: hylafax-users-bounce@xxxxxxxxxxx [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Roper, Brent
Sent: Friday, July 16, 2004 2:05 PM
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users]

All,

This is a box running SuSE 9.0 with 6 USR 56k fax/modems on it. I have written a script so that each time a fax is received it pipes faxcover into sendfax to send a 1 page fax back to the original sender to confirm the receipt of the fax. On this particular box the only port that can send out a fax is ttyS0 all the rest get No carrier detected. I have tried with the @ and without neither work. Here is an excerpt from the log file.

"Jul 16 08:22:19.58: [30109]: --> return result ""15129281825"""

Jul 16 08:22:19.58: [30109]: <-- [12:AT+FCLASS=1\r]

Jul 16 08:22:19.82: [30109]: --> [2:OK]

"Jul 16 08:22:19.82: [30109]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled"

Jul 16 08:22:19.92: [30109]: DIAL 15129281825

Jul 16 08:22:19.92: [30109]: <-- [16:ATDT15129281825\r]

Jul 16 08:23:17.84: [30109]: --> [10:NO CARRIER]

Jul 16 08:23:17.84: [30109]: SEND FAILED: JOB 60 DEST 5129281825 ERR No carrier detected

Thanks in advance for any help.

Brent