|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] T.30 T2 timeout errors
Greetings,
I'm wondering if anyone out there can give me some insight into the T.30 T2
timeout errors. I notice that I get these errors when I try to receive a
large fax (over 10 pages). I'm not sure if this is a problem with my
configuration or my modem. Below I have included some information about my
setup and some logs. Thank you for your help!
System Info
=========
HylaFax Version: 4.1.8-13
System: Debian Linux with 2.4.25 kernel
Modem: USR U.S. Robotics Sportster 33600 Fax V4.1 (FLASH rev 4.1.55)
hfaxd.conf (excluding comments)
========
LogFacility: daemon
ServerTracing: 0x001
JobFmt: "%-3j %3i %1a %6.6o %-14.14e %5P %5D %7z %.25s"
config.ttyS0
=========
CountryCode: 1
AreaCode: 416
FAXNumber: 416.###.####
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 0x08501
SessionTracing: 0x08501
RecvFileMode: 0640
LogFileMode: 0640
DeviceMode: 0660
RingsBeforeAnswer: 1
SpeakerVolume: on
GettyArgs: "-r -b %l"
LocalIdentifier: "Hylafax Server"
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 100
ModemReadyState: R
ModemType: Class1 # use class 1 interface
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: xonxoff # software flow control
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or
not)
ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow
control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow
control
ModemResultCodesCmd: ATQ0X4 # enable result codes
ModemMfrQueryCmd: !USR
ModemModelQueryCmd: ATI3
ModemRevQueryCmd: ATI7 # XXX returns a multi-line result
Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no flow control
Class1HFLOCmd: AT&H1&I0&R2 # setup modem for hardware flow
control
Class1SFLOCmd: "" # modem does this automatically
Class1ResponseWaitCmd: AT+FRS=1 # wait after sending TCF for
response
ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0
ModemAnswerCmd: AT+FCLASS=1A # answer in Class 1
Class2NRCmd: AT+FNR=1,1,1,0
Transcript of session follows (example 1)
====================
Jul 12 11:37:35.49: [ 618]: SESSION BEGIN 00002365 1416416#######
Jul 12 11:37:35.49: [ 618]: HylaFAX (tm) Version 4.1.8
Jul 12 11:37:40.28: [ 618]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Jul 12 11:37:40.28: [ 618]: STATE CHANGE: ANSWERING -> RECEIVING
Jul 12 11:38:21.96: [ 618]: RECV FAX (00002365): recvq/fax01890.tif from
<UNSPECIFIED>, route to <unspecified>, 0 pages in 0:41
Jul 12 11:38:23.51: [ 618]: RECV FAX (00002365): session with <UNSPECIFIED>
terminated abnormally: T.30 T2 timeout, expected page not received
Jul 12 11:38:23.51: [ 618]: RECV FAX: bin/faxrcvd "recvq/fax01890.tif"
"ttyS0" "00002365" "T.30 T2 timeout, expected page not received" "" ""
Transcript of session follows (example 2)
=====================
Jul 08 14:31:14.83: [ 619]: SESSION BEGIN 00002234 1416#######
Jul 08 14:31:14.83: [ 619]: HylaFAX (tm) Version 4.1.8
Jul 08 14:31:19.62: [ 619]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Jul 08 14:31:19.62: [ 619]: STATE CHANGE: ANSWERING -> RECEIVING
Jul 08 14:31:40.31: [ 619]: RECV/CQ: Bad 1D pixel count, row 1045, got 0,
expected 1728
Jul 08 14:31:40.31: [ 619]: RECV/CQ: Bad 1D pixel count, row 1046, got 0,
expected 1728
Jul 08 14:31:40.31: [ 619]: RECV/CQ: Bad 1D pixel count, row 1047, got 0,
expected 1728
Jul 08 14:31:40.31: [ 619]: RECV/CQ: Bad 1D pixel count, row 1048, got 0,
expected 1728
Jul 08 14:31:40.31: [ 619]: RECV/CQ: Bad 1D pixel count, row 1049, got 0,
expected 1728
Jul 08 14:31:40.31: [ 619]: RECV/CQ: Bad 1D pixel count, row 1050, got
2225, expected 1728
Jul 08 14:31:40.31: [ 619]: RECV/CQ: Adjusting for trailing noise (6 run)
Jul 08 14:31:42.76: [ 619]: RECV FAX (00002234): from 705 #######, page 1
in 0:17, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Jul 08 14:31:57.89: [ 619]: RECV/CQ: Bad 1D pixel count, row 1049, got 0,
expected 1728
Jul 08 14:31:57.89: [ 619]: RECV/CQ: Bad 1D pixel count, row 1050, got 0,
expected 1728
Jul 08 14:31:57.89: [ 619]: RECV/CQ: Bad 1D pixel count, row 1051, got 0,
expected 1728
Jul 08 14:31:57.89: [ 619]: RECV/CQ: Bad 1D pixel count, row 1052, got 0,
expected 1728
Jul 08 14:31:57.89: [ 619]: RECV/CQ: Bad 1D pixel count, row 1053, got 0,
expected 1728
Jul 08 14:31:58.03: [ 619]: RECV/CQ: Bad 1D pixel count, row 1054, got
2374, expected 1728
Jul 08 14:31:58.03: [ 619]: RECV/CQ: Adjusting for trailing noise (6 run)
Jul 08 14:31:59.50: [ 619]: RECV FAX (00002234): from 705 #######, page 2
in 0:17, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Jul 08 14:32:16.06: [ 619]: RECV/CQ: Bad 1D pixel count, row 1046, got 0,
expected 1728
Jul 08 14:32:16.06: [ 619]: RECV/CQ: Bad 1D pixel count, row 1047, got 0,
expected 1728
Jul 08 14:32:16.06: [ 619]: RECV/CQ: Bad 1D pixel count, row 1048, got 0,
expected 1728
Jul 08 14:32:16.06: [ 619]: RECV/CQ: Bad 1D pixel count, row 1049, got 0,
expected 1728
Jul 08 14:32:16.06: [ 619]: RECV/CQ: Bad 1D pixel count, row 1050, got 0,
expected 1728
Jul 08 14:32:16.06: [ 619]: RECV/CQ: Invalid WhiteTable code word, row
1051, x 898
Jul 08 14:32:16.06: [ 619]: RECV/CQ: Bad 1D pixel count, row 1051, got 898,
expected 1728
Jul 08 14:32:16.18: [ 619]: RECV/CQ: Adjusting for trailing noise (6 run)
Jul 08 14:32:18.26: [ 619]: RECV FAX (00002234): from 705 #######, page 3
in 0:19, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Jul 08 14:32:43.12: [ 619]: RECV/CQ: Bad 1D pixel count, row 1045, got 0,
expected 1728
Jul 08 14:32:43.18: [ 619]: RECV/CQ: Bad 1D pixel count, row 1046, got 0,
expected 1728
Jul 08 14:32:43.18: [ 619]: RECV/CQ: Bad 1D pixel count, row 1047, got 0,
expected 1728
Jul 08 14:32:43.18: [ 619]: RECV/CQ: Bad 1D pixel count, row 1048, got 0,
expected 1728
Jul 08 14:32:43.18: [ 619]: RECV/CQ: Bad 1D pixel count, row 1049, got 0,
expected 1728
Jul 08 14:32:43.18: [ 619]: RECV/CQ: Invalid WhiteTable code word, row
1050, x 206
Jul 08 14:32:43.18: [ 619]: RECV/CQ: Bad 1D pixel count, row 1050, got 206,
expected 1728
Jul 08 14:32:43.18: [ 619]: RECV/CQ: Adjusting for trailing noise (6 run)
Jul 08 14:32:45.25: [ 619]: RECV FAX (00002234): from 705 #######, page 4
in 0:27, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Jul 08 14:33:15.41: [ 619]: RECV/CQ: Bad 1D pixel count, row 1044, got 0,
expected 1728
Jul 08 14:33:15.41: [ 619]: RECV/CQ: Bad 1D pixel count, row 1045, got 0,
expected 1728
Jul 08 14:33:15.41: [ 619]: RECV/CQ: Bad 1D pixel count, row 1046, got 0,
expected 1728
Jul 08 14:33:15.41: [ 619]: RECV/CQ: Bad 1D pixel count, row 1047, got 0,
expected 1728
Jul 08 14:33:15.41: [ 619]: RECV/CQ: Bad 1D pixel count, row 1048, got 0,
expected 1728
Jul 08 14:33:15.41: [ 619]: RECV/CQ: Bad 1D pixel count, row 1049, got
1854, expected 1728
Jul 08 14:33:15.41: [ 619]: RECV/CQ: Adjusting for trailing noise (6 run)
Jul 08 14:33:46.69: [ 619]: RECV FAX (00002234): from 705 #######, page 5
in 1:01, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Jul 08 14:33:49.48: [ 619]: RECV FAX (00002234): recvq/fax01782.tif from
705 #######, route to <unspecified>, 5 pages in 2:30
Jul 08 14:33:49.51: [ 619]: RECV FAX (00002234): session with 705 #######
terminated abnormally: T.30 T2 timeout, expected page not received
Jul 08 14:33:49.51: [ 619]: RECV FAX: bin/faxrcvd "recvq/fax01782.tif"
"ttyS0" "00002234" "T.30 T2 timeout, expected page not received" "" ""
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
