[hylafax-users] Waiting for modem to come ready ... wrong config ?

Greetings list.

Im having little difficulties getting the right config, in order to make my modem work ok with hylafax.

Invoking faxstat, i get thoses messages :

HylaFAX scheduler on [hostname]: Running
Modem ttyS0 (+1.xxx.xxx.xxxx): Waiting for modem to come ready

Here is some debug info obtained when calling up the modem, initializing it, and dialing on my cell.

[root@fax sendq]# cu -l /dev/ttyS0
Connected.
at+fclass=?
0,1,2.0

atz

atdt 514xxxxxxx

NO CARRIER

ati3
Sportster 28800/Fax V6.0

OK
ati6
USRobotics Sportster 28800 V.34 Fax Link Diagnostics...

Chars sent                    0      Chars Received                0
Chars lost                    0
Octets sent                   0      Octets Received               0
Blocks sent                   0      Blocks Received               0
Blocks resent                 0

Retrains Requested            0      Retrains Granted              0
Line Reversals                0      Blers                         0
Link Timeouts                 0      Link Naks                     0

Data Compression       NONE
Equalization           Long
Fallback               Disabled
Last Call              00:00:00

Disconnect Reason is Keypress Abort
OK

~.

Disconnected.

Im using the default config, which i copied/pasted here ... default one for now ([spooldir]/config/rockwell-rc), included in this mail below.

Note I just want to setup a mail to fax gateway, i do not care about answering calls.

Any pointers appreciated.

# $Id: rockwell-rc,v 1.2 2002/04/07 20:29:26 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# Configuration for a Rockwell-based modem not otherwise handled by
# another prototype configuration file. This file assumes the modem
# is compatible with the Rc144AC, RC96AC or RC144DP.
#
# This configuration file sets up the modem to run at 38.4 with
# RTS/CTS flow control used by default. XON/XOFF is automatically
# enabled for fax recv. Beware of modems that also lock sending
# to 19.2; add ModemSendBeginCmd: "<19200>" if this is required.
# Also beware that the adaptive-answer facility, when supported,
# is often unreliable.
#
# CONFIG: CLASS2: ROCKWELL*-*
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use class 2 interface
ModemRate:              19200
ModemFlowControl:       rtscts          # default
#
#ModemResetCmds:        AT&F2           # what you want for a Supra
ModemNoFlowCmd:         AT&K            # disable flow control cmd
ModemHardFlowCmd:       AT&K3           # hardware flow control cmd
ModemSoftFlowCmd:       AT&K4           # software flow control cmd
ModemSetupDTRCmd:       AT&D3           # DTR off causes modem to reset
#ModemSetupDTRCmd:      AT&D2S25=1S38=0 # Dynalink 1414VE needs this
ModemSetupDCDCmd:       AT&C1           # DCD follows carrier
ModemSetupAACmd:        AT+FAA=1+FCLASS=0 # enable in current class
#
ModemSendFillOrder:     LSB2MSB         # as expected
ModemRecvFillOrder:     MSB2LSB         # opposite of what makes sense
#
ModemAnswerFaxBeginCmd: "<19200><xon>" # modem switches on fax receive
#
# Caller ID configuration setup for Supra.
#
#QualifyCID:            etc/cid         # CID access control list file
#CIDNumber:             "NMBR = "       # pattern string for phone number info
#CIDName:               "NAME = "       # pattern string for identity info

-
Frederic Trudeau <ftrudeau@xxxxxxx>
Programmation / Departement reseau
Communications Accessibles Montreal
Web: http://www.cam.org

----- Original Message -----

From: Michael Balamuth

To: hylafax-users@xxxxxxxxxxx

Sent: Monday, June 21, 2004 4:30 PM

Subject: [hylafax-users] List protocol question

Would it be considered inappropriate in this list to ask for a comparison of the stronger points of a commercial fax system like Lightning Fax compared to Hylafax? In other words, would the experts on this list welcome or be willing to expound on their comparative knowledge of another system compared to Hylafax?

Thanks

Michael Balamuth

mlb@xxxxxxxxxx