[hylafax-users] Problem in sending TCF

To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] Problem in sending TCF
From: andrea.satriani@xxxxxx
Date: Wed, 19 May 2004 12:06:45 +0200
Hi all,
I ask you for help! Sending fax I have problem in sending TCF.
This is log:

mag 19 11:30:49.81: [25442]: SESSION BEGIN 00000135 1415400
mag 19 11:30:49.81: [25442]: HylaFAX (tm) Version 4.1.8
mag 19 11:30:49.81: [25442]: SEND FAX: JOB 6075 DEST 400 COMMID 00000135
DEVICE '/dev/ttyS0'
mag 19 11:30:49.81: [25442]: MODEM set DTR OFF
mag 19 11:30:49.81: [25442]: DELAY 75 ms
mag 19 11:30:49.89: [25442]: MODEM set DTR ON
mag 19 11:30:49.89: [25442]: DELAY 2600 ms
mag 19 11:30:53.50: [25442]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS, output flow RTS/CTS
mag 19 11:30:53.50: [25442]: DELAY 10 ms
mag 19 11:30:53.51: [25442]: MODEM flush i/o
mag 19 11:30:53.51: [25442]: <-- [4:ATZ\r]
mag 19 11:30:53.67: [25442]: --> [2:OK]
mag 19 11:30:53.67: [25442]: DELAY 3000 ms
mag 19 11:30:56.67: [25442]: <-- [5:ATE0\r]
mag 19 11:30:56.68: [25442]: --> [4:ATE0]
mag 19 11:30:56.68: [25442]: --> [2:OK]
mag 19 11:30:56.68: [25442]: <-- [5:ATV1\r]
mag 19 11:30:56.69: [25442]: --> [2:OK]
mag 19 11:30:56.69: [25442]: <-- [5:ATQ0\r]
mag 19 11:30:56.70: [25442]: --> [2:OK]
mag 19 11:30:56.70: [25442]: <-- [7:ATS0=0\r]
mag 19 11:30:56.71: [25442]: --> [2:OK]
mag 19 11:30:56.71: [25442]: <-- [7:ATS8=2\r]
mag 19 11:30:56.72: [25442]: --> [2:OK]
mag 19 11:30:56.72: [25442]: <-- [9:ATS7=120\r]
mag 19 11:30:56.74: [25442]: --> [2:OK]
mag 19 11:30:56.74: [25442]: <-- [12:AT+FCLASS=1\r]
mag 19 11:30:56.76: [25442]: --> [2:OK]
mag 19 11:30:56.76: [25442]: <-- [7:ATL0M1\r]
mag 19 11:30:56.77: [25442]: --> [2:OK]
mag 19 11:30:56.77: [25442]: STATE CHANGE: RUNNING -> SENDING
mag 19 11:30:56.77: [25442]: MODEM input buffering enabled
mag 19 11:30:56.77: [25442]: <-- [12:AT+FCLASS=1\r]
mag 19 11:30:56.89: [25442]: --> [2:OK]
mag 19 11:30:56.89: [25442]: DIAL 400
mag 19 11:30:56.89: [25442]: <-- [8:ATDT400\r]
mag 19 11:31:09.68: [25442]: --> [7:CONNECT]
mag 19 11:31:09.68: [25442]: MODEM input buffering disabled
mag 19 11:31:09.68: [25442]: Andrea: Partito Timeout settato a 10 sec
mag 19 11:31:10.73: [25442]: --> HDLC<25:FF C0 02 0C 0C 2C 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04 8D C4>
mag 19 11:31:10.74: [25442]: --> [2:OK]
mag 19 11:31:10.74: [25442]: REMOTE CSI "400"
mag 19 11:31:10.74: [25442]: <-- [9:AT+FRH=3\r]
mag 19 11:31:10.76: [25442]: --> [7:CONNECT]
mag 19 11:31:10.76: [25442]: Andrea: Partito Timeout settato a 10 sec
mag 19 11:31:11.16: [25442]: --> HDLC<12:FF C8 01 00 76 5F 01 79 03 00 20
4D>
mag 19 11:31:11.17: [25442]: --> [2:OK]
mag 19 11:31:11.17: [25442]: REMOTE best rate 14400 bit/s
mag 19 11:31:11.17: [25442]: REMOTE max page width 2432 pixels in 303 mm
mag 19 11:31:11.17: [25442]: REMOTE max unlimited page length
mag 19 11:31:11.17: [25442]: REMOTE best vres 7.7 line/mm
mag 19 11:31:11.17: [25442]: REMOTE best format 1-D MR
mag 19 11:31:11.17: [25442]: REMOTE best 0 ms/scanline
mag 19 11:31:11.17: [25442]: USE 14400 bit/s
mag 19 11:31:11.17: [25442]: USE 0 ms/scanline
mag 19 11:31:11.17: [25442]: SEND file "docq/doc6075.cover;30"
mag 19 11:31:11.17: [25442]: USE page width 1728 pixels in 215 mm
mag 19 11:31:11.17: [25442]: USE unlimited page length
mag 19 11:31:11.17: [25442]: USE 3.85 line/mm
mag 19 11:31:11.17: [25442]: USE 1-D MR
mag 19 11:31:11.17: [25442]: SEND training at v.17 14400 bit/s
mag 19 11:31:11.17: [25442]: <-- [9:AT+FTH=3\r]
mag 19 11:31:11.22: [25442]: --> [7:CONNECT]
mag 19 11:31:11.22: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04>
mag 19 11:31:11.22: [25442]: <-- data [23]
mag 19 11:31:11.22: [25442]: <-- data [2]
mag 19 11:31:13.01: [25442]: --> [7:CONNECT]
mag 19 11:31:13.01: [25442]: <-- HDLC<6:FF C8 C1 00 44 1E>
mag 19 11:31:13.01: [25442]: <-- data [6]
mag 19 11:31:13.01: [25442]: <-- data [2]
mag 19 11:31:13.45: [25442]: --> [2:OK]
mag 19 11:31:13.45: [25442]: <-- [9:AT+FTS=7\r]
mag 19 11:31:13.54: [25442]: --> [2:OK]
mag 19 11:31:13.54: [25442]: <-- [11:AT+FTM=145\r]
mag 19 11:31:13.58: [25442]: --> [7:CONNECT]
mag 19 11:31:13.58: [25442]: <-- data [1024]
mag 19 11:31:13.58: [25442]: <-- data [1024]
mag 19 11:31:13.58: [25442]: <-- data [652]
mag 19 11:31:13.58: [25442]: <-- data [2]
mag 19 11:31:16.69: [25442]: --> [9:]
mag 19 11:31:16.69: [25442]: Problem sending TCF data
mag 19 11:31:16.69: [25442]: <-- [9:AT+FRH=3\r]
mag 19 11:31:16.69: [25442]: --> [2:OK]
mag 19 11:31:19.30: [25442]: --> [7:CONNECT]
mag 19 11:31:19.30: [25442]: Andrea: Partito Timeout settato a 10 sec
mag 19 11:31:21.89: [25442]: --> [3:11 10 03]
mag 19 11:31:21.89: [25442]: --> [5:ERROR]
mag 19 11:31:21.89: [25442]: MODEM Command error
mag 19 11:31:21.89: [25442]: FCS error
mag 19 11:31:21.89: [25442]: DELAY 1500 ms
mag 19 11:31:23.39: [25442]: SEND training at v.17 12000 bit/s
mag 19 11:31:23.39: [25442]: <-- [9:AT+FTH=3\r]
mag 19 11:31:23.44: [25442]: --> [7:CONNECT]
mag 19 11:31:23.44: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04>
mag 19 11:31:23.44: [25442]: <-- data [23]
mag 19 11:31:23.44: [25442]: <-- data [2]
mag 19 11:31:25.23: [25442]: --> [7:CONNECT]
mag 19 11:31:25.23: [25442]: <-- HDLC<6:FF C8 C1 00 54 1E>
mag 19 11:31:25.23: [25442]: <-- data [6]
mag 19 11:31:25.23: [25442]: <-- data [2]
mag 19 11:31:25.66: [25442]: --> [2:OK]
mag 19 11:31:25.66: [25442]: <-- [9:AT+FTS=7\r]
mag 19 11:31:25.75: [25442]: --> [2:OK]
mag 19 11:31:25.75: [25442]: <-- [11:AT+FTM=121\r]
mag 19 11:31:25.79: [25442]: --> [7:CONNECT]
mag 19 11:31:25.79: [25442]: <-- data [1024]
mag 19 11:31:25.79: [25442]: <-- data [1024]
mag 19 11:31:25.79: [25442]: <-- data [202]
mag 19 11:31:25.79: [25442]: <-- data [2]
mag 19 11:31:28.90: [25442]: --> [9:]
mag 19 11:31:28.90: [25442]: Problem sending TCF data
mag 19 11:31:28.90: [25442]: <-- [9:AT+FRH=3\r]
mag 19 11:31:28.90: [25442]: --> [2:OK]
mag 19 11:31:31.54: [25442]: --> [7:CONNECT]
mag 19 11:31:31.54: [25442]: Andrea: Partito Timeout settato a 10 sec
mag 19 11:31:34.09: [25442]: --> [3:11 10 03]
mag 19 11:31:34.09: [25442]: --> [5:ERROR]
mag 19 11:31:34.09: [25442]: MODEM Command error
mag 19 11:31:34.09: [25442]: FCS error
mag 19 11:31:34.09: [25442]: DELAY 1500 ms
mag 19 11:31:35.59: [25442]: SEND training at v.17 9600 bit/s
mag 19 11:31:35.59: [25442]: <-- [9:AT+FTH=3\r]
mag 19 11:31:35.64: [25442]: --> [7:CONNECT]
mag 19 11:31:35.64: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04>
mag 19 11:31:35.64: [25442]: <-- data [23]
mag 19 11:31:35.64: [25442]: <-- data [2]
mag 19 11:31:37.42: [25442]: --> [7:CONNECT]
mag 19 11:31:37.42: [25442]: <-- HDLC<6:FF C8 C1 00 64 1E>
mag 19 11:31:37.43: [25442]: <-- data [6]
mag 19 11:31:37.43: [25442]: <-- data [2]
mag 19 11:31:37.85: [25442]: --> [2:OK]
mag 19 11:31:37.85: [25442]: <-- [9:AT+FTS=7\r]
mag 19 11:31:37.94: [25442]: --> [2:OK]
mag 19 11:31:37.94: [25442]: <-- [10:AT+FTM=97\r]
mag 19 11:31:37.98: [25442]: --> [7:CONNECT]
mag 19 11:31:37.98: [25442]: <-- data [1024]
mag 19 11:31:37.98: [25442]: <-- data [776]
mag 19 11:31:37.98: [25442]: <-- data [2]
mag 19 11:31:41.09: [25442]: --> [13:]
mag 19 11:31:41.09: [25442]: Problem sending TCF data
mag 19 11:31:41.09: [25442]: <-- [9:AT+FRH=3\r]
mag 19 11:31:41.09: [25442]: --> [2:OK]
mag 19 11:31:43.74: [25442]: --> [7:CONNECT]
mag 19 11:31:43.74: [25442]: Andrea: Partito Timeout settato a 10 sec
mag 19 11:31:46.28: [25442]: --> [3:11 10 03]
mag 19 11:31:46.29: [25442]: --> [5:ERROR]
mag 19 11:31:46.29: [25442]: MODEM Command error
mag 19 11:31:46.29: [25442]: FCS error
mag 19 11:31:46.29: [25442]: DELAY 1500 ms
mag 19 11:31:47.79: [25442]: SEND training at v.17 7200 bit/s
mag 19 11:31:47.79: [25442]: <-- [9:AT+FTH=3\r]
mag 19 11:31:47.84: [25442]: --> [7:CONNECT]
mag 19 11:31:47.84: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04>
mag 19 11:31:47.84: [25442]: <-- data [23]
mag 19 11:31:47.84: [25442]: <-- data [2]
mag 19 11:31:49.63: [25442]: --> [7:CONNECT]
mag 19 11:31:49.63: [25442]: <-- HDLC<6:FF C8 C1 00 74 1E>
mag 19 11:31:49.63: [25442]: <-- data [6]
mag 19 11:31:49.63: [25442]: <-- data [2]
mag 19 11:31:50.06: [25442]: --> [2:OK]
mag 19 11:31:50.06: [25442]: <-- [9:AT+FTS=7\r]
mag 19 11:31:50.15: [25442]: --> [2:OK]
mag 19 11:31:50.15: [25442]: <-- [10:AT+FTM=73\r]
mag 19 11:31:50.20: [25442]: --> [7:CONNECT]
mag 19 11:31:50.20: [25442]: <-- data [1024]
mag 19 11:31:50.20: [25442]: <-- data [326]
mag 19 11:31:50.20: [25442]: <-- data [2]
mag 19 11:31:53.32: [25442]: --> [110:]
mag 19 11:31:53.32: [25442]: Problem sending TCF data
mag 19 11:31:53.32: [25442]: <-- [9:AT+FRH=3\r]
mag 19 11:31:53.32: [25442]: --> [2:OK]
mag 19 11:31:55.92: [25442]: --> [7:CONNECT]
mag 19 11:31:55.92: [25442]: Andrea: Partito Timeout settato a 10 sec
mag 19 11:31:58.49: [25442]: --> [2:10 03]
mag 19 11:31:58.50: [25442]: --> [5:ERROR]
mag 19 11:31:58.50: [25442]: MODEM Command error
mag 19 11:31:58.50: [25442]: FCS error
mag 19 11:31:58.50: [25442]: DELAY 1500 ms
mag 19 11:32:00.00: [25442]: SEND training at v.27ter 4800 bit/s
mag 19 11:32:00.00: [25442]: <-- [9:AT+FTH=3\r]
mag 19 11:32:00.05: [25442]: --> [7:CONNECT]
mag 19 11:32:00.05: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04>
mag 19 11:32:00.05: [25442]: <-- data [23]
mag 19 11:32:00.05: [25442]: <-- data [2]
mag 19 11:32:01.84: [25442]: --> [7:CONNECT]
mag 19 11:32:01.84: [25442]: <-- HDLC<6:FF C8 C1 00 50 1E>
mag 19 11:32:01.84: [25442]: <-- data [6]
mag 19 11:32:01.84: [25442]: <-- data [2]
mag 19 11:32:02.28: [25442]: --> [2:OK]
mag 19 11:32:02.28: [25442]: <-- [9:AT+FTS=7\r]
mag 19 11:32:02.37: [25442]: --> [2:OK]
mag 19 11:32:02.37: [25442]: <-- [10:AT+FTM=48\r]
mag 19 11:32:02.41: [25442]: --> [7:CONNECT]
mag 19 11:32:02.41: [25442]: <-- data [900]
mag 19 11:32:02.41: [25442]: <-- data [2]
mag 19 11:32:04.84: [25442]: --> [2:OK]
mag 19 11:32:04.84: [25442]: <-- [9:AT+FRH=3\r]
mag 19 11:32:07.45: [25442]: --> [7:CONNECT]
mag 19 11:32:07.45: [25442]: Andrea: Partito Timeout settato a 10 sec
mag 19 11:32:10.03: [25442]: --> [2:10 03]
mag 19 11:32:10.03: [25442]: --> [5:ERROR]
mag 19 11:32:10.03: [25442]: MODEM Command error
mag 19 11:32:10.03: [25442]: FCS error
mag 19 11:32:10.03: [25442]: DELAY 1500 ms
mag 19 11:32:11.53: [25442]: SEND training at v.27ter fallback mode 2400
bit/s
mag 19 11:32:11.53: [25442]: <-- [9:AT+FTH=3\r]
mag 19 11:32:11.58: [25442]: --> [7:CONNECT]
mag 19 11:32:11.58: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04>
mag 19 11:32:11.58: [25442]: <-- data [23]
mag 19 11:32:11.58: [25442]: <-- data [2]
mag 19 11:32:13.37: [25442]: --> [7:CONNECT]
mag 19 11:32:13.37: [25442]: <-- HDLC<6:FF C8 C1 00 40 1E>
mag 19 11:32:13.37: [25442]: <-- data [6]
mag 19 11:32:13.37: [25442]: <-- data [2]
mag 19 11:32:13.80: [25442]: --> [2:OK]
mag 19 11:32:13.80: [25442]: <-- [9:AT+FTS=7\r]
mag 19 11:32:13.90: [25442]: --> [2:OK]
mag 19 11:32:13.90: [25442]: <-- [10:AT+FTM=24\r]
mag 19 11:32:13.95: [25442]: --> [7:CONNECT]
mag 19 11:32:13.95: [25442]: <-- data [450]
mag 19 11:32:13.95: [25442]: <-- data [2]
mag 19 11:32:16.62: [25442]: --> [2:OK]
mag 19 11:32:16.62: [25442]: <-- [9:AT+FRH=3\r]
mag 19 11:32:19.28: [25442]: --> [7:CONNECT]
mag 19 11:32:19.28: [25442]: Andrea: Partito Timeout settato a 10 sec
mag 19 11:32:21.83: [25442]: --> [2:10 03]
mag 19 11:32:21.83: [25442]: --> [5:ERROR]
mag 19 11:32:21.83: [25442]: MODEM Command error
mag 19 11:32:21.83: [25442]: FCS error
mag 19 11:32:21.83: [25442]: DELAY 1500 ms
mag 19 11:32:23.33: [25442]: TRAINING failed
mag 19 11:32:23.33: [25442]: <-- [9:AT+FTH=3\r]
mag 19 11:32:23.38: [25442]: --> [7:CONNECT]
mag 19 11:32:23.38: [25442]: <-- HDLC<3:FF C8 DF>
mag 19 11:32:23.38: [25442]: <-- data [3]
mag 19 11:32:23.38: [25442]: <-- data [2]
mag 19 11:32:24.70: [25442]: --> [2:OK]
mag 19 11:32:24.70: [25442]: MODEM input buffering enabled
mag 19 11:32:24.70: [25442]: <-- [5:ATH0\r]
mag 19 11:32:26.25: [25442]: --> [2:OK]
mag 19 11:32:26.25: [25442]: MODEM set DTR OFF
mag 19 11:32:26.25: [25442]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
mag 19 11:32:26.25: [25442]: SESSION END



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
Follow-Ups:
- Re: [hylafax-users] Problem in sending TCF
  - From: Lee Howard
Prev by Date: [hylafax-users] Solution to files corrupted by libtiff 3.6.0 on SuSE 9.1
Next by Date: Re: [hylafax-users] Attached TIFF mail delivery
Previous by thread: [hylafax-users] Solution to files corrupted by libtiff 3.6.0 on SuSE 9.1
Next by thread: Re: [hylafax-users] Problem in sending TCF
Index(es):
- Main
- Thread
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services