Re: [hylafax-users] AT+FDT -> FHS:25 (DCS) errors

To: "'Giulio Orsero'" <giulioo@xxxxxxxxx>, hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] AT+FDT -> FHS:25 (DCS) errors
From: Steve Tuckner <STUCKNER@xxxxxxxxxxxxx>
Reply-to: Steve Tuckner <sat@xxxxxxxxxxxxx>
Date: Tue, 13 Apr 2004 09:22:39 -0500

What is the phone number for this fax machine. I would like to try it.

Obviously 0,0123456789 is not the correct phone number.

Steve Tuckner
Multi-Tech Systems

> -----Original Message-----
> From: hylafax-users-bounce@xxxxxxxxxxx
> [mailto:hylafax-users-bounce@xxxxxxxxxxx]On Behalf Of Giulio Orsero
> Sent: Tuesday, April 13, 2004 4:41 AM
> To: hylafax-users@xxxxxxxxxxx
> Subject: [hylafax-users] AT+FDT -> FHS:25 (DCS) errors
> 
> 
> HylaFAX-4.1.7, MT5634ZBA-V92 fw1.28c (latest) used in class-2.1
> 
> There is a particular remote fax machine (don't know make/model) which
> always causes DCS problems, as you can see in attached log. 
> Do you think
> upgrading HylaFAX could help or this is a kind of 
> incompatibility between
> modem firmware and remote machine which is unsolvable, but 
> for using it in
> class1?
> 
> Thanks
> 
> Mar 22 14:24:27.14: [25656]: SESSION BEGIN 00065987 390123456789
> Mar 22 14:24:27.14: [25656]: HylaFAX (tm) Version 4.1.7
> Mar 22 14:24:27.14: [25656]: SEND FAX: JOB 16160 DEST 
> 0123456789 COMMID 00065987 DEVICE '/dev/ttyS1'
> Mar 22 14:24:27.14: [25656]: DELAY 75 ms
> Mar 22 14:24:27.22: [25656]: DELAY 2600 ms
> Mar 22 14:24:30.83: [25656]: DELAY 10 ms
> Mar 22 14:24:30.84: [25656]: <-- [4:ATZ\r]
> Mar 22 14:24:32.11: [25656]: --> [2:OK]
> Mar 22 14:24:32.11: [25656]: DELAY 3000 ms
> Mar 22 14:24:35.11: [25656]: <-- [5:ATX3\r]
> Mar 22 14:24:35.12: [25656]: --> [4:ATX3]
> Mar 22 14:24:35.12: [25656]: --> [2:OK]
> Mar 22 14:24:35.12: [25656]: <-- [5:ATE0\r]
> Mar 22 14:24:35.13: [25656]: --> [4:ATE0]
> Mar 22 14:24:35.13: [25656]: --> [2:OK]
> Mar 22 14:24:35.13: [25656]: <-- [5:ATV1\r]
> Mar 22 14:24:35.14: [25656]: --> [2:OK]
> Mar 22 14:24:35.14: [25656]: <-- [5:ATQ0\r]
> Mar 22 14:24:35.15: [25656]: --> [2:OK]
> Mar 22 14:24:35.15: [25656]: <-- [7:ATS0=0\r]
> Mar 22 14:24:35.16: [25656]: --> [2:OK]
> Mar 22 14:24:35.16: [25656]: <-- [7:ATS8=2\r]
> Mar 22 14:24:35.17: [25656]: --> [2:OK]
> Mar 22 14:24:35.17: [25656]: <-- [8:ATS7=60\r]
> Mar 22 14:24:35.18: [25656]: --> [2:OK]
> Mar 22 14:24:35.18: [25656]: <-- [6:AT&K4\r]
> Mar 22 14:24:35.19: [25656]: --> [2:OK]
> Mar 22 14:24:35.19: [25656]: <-- [21:AT+FCLASS=2.1;+FRY=4\r]
> Mar 22 14:24:35.20: [25656]: --> [2:OK]
> Mar 22 14:24:35.20: [25656]: <-- [9:AT+FLO=1\r]
> Mar 22 14:24:35.21: [25656]: --> [2:OK]
> Mar 22 14:24:35.21: [25656]: <-- [9:AT+FPP=0\r]
> Mar 22 14:24:35.22: [25656]: --> [2:OK]
> Mar 22 14:24:35.22: [25656]: <-- [9:AT+FBO=0\r]
> Mar 22 14:24:35.23: [25656]: --> [2:OK]
> Mar 22 14:24:35.23: [25656]: <-- [10:AT+FCT=30\r]
> Mar 22 14:24:35.24: [25656]: --> [2:OK]
> Mar 22 14:24:35.24: [25656]: <-- [11:AT+FCQ=1,0\r]
> Mar 22 14:24:35.25: [25656]: --> [2:OK]
> Mar 22 14:24:35.25: [25656]: <-- [15:AT+FNR=1,1,1,1\r]
> Mar 22 14:24:35.26: [25656]: --> [2:OK]
> Mar 22 14:24:35.26: [25656]: <-- [13:AT+FAP=1,1,1\r]
> Mar 22 14:24:35.27: [25656]: --> [2:OK]
> Mar 22 14:24:35.27: [25656]: <-- [9:AT+FIE=0\r]
> Mar 22 14:24:35.28: [25656]: --> [2:OK]
> Mar 22 14:24:35.28: [25656]: <-- [23:AT+FCC=1,D,2,2,3,1,0,0\r]
> Mar 22 14:24:35.29: [25656]: --> [2:OK]
> Mar 22 14:24:35.29: [25656]: <-- [5:ATM0\r]
> Mar 22 14:24:35.30: [25656]: --> [2:OK]
> Mar 22 14:24:35.30: [25656]: sched policy=1, priority=1
> Mar 22 14:24:35.30: [25656]: <-- [21:AT+FCLASS=2.1;+FRY=4\r]
> Mar 22 14:24:35.41: [25656]: --> [2:OK]
> Mar 22 14:24:35.41: [25656]: <-- [9:AT+FLO=1\r]
> Mar 22 14:24:35.52: [25656]: --> [2:OK]
> Mar 22 14:24:35.52: [25656]: <-- [9:AT+FPP=0\r]
> Mar 22 14:24:35.63: [25656]: --> [2:OK]
> Mar 22 14:24:35.63: [25656]: <-- [9:AT+FBO=0\r]
> Mar 22 14:24:35.74: [25656]: --> [2:OK]
> Mar 22 14:24:35.74: [25656]: <-- [10:AT+FCT=30\r]
> Mar 22 14:24:35.85: [25656]: --> [2:OK]
> Mar 22 14:24:35.85: [25656]: <-- [11:AT+FCQ=1,0\r]
> Mar 22 14:24:35.96: [25656]: --> [2:OK]
> Mar 22 14:24:35.96: [25656]: <-- [15:AT+FNR=1,1,1,1\r]
> Mar 22 14:24:36.07: [25656]: --> [2:OK]
> Mar 22 14:24:36.07: [25656]: <-- [13:AT+FAP=1,1,1\r]
> Mar 22 14:24:36.18: [25656]: --> [2:OK]
> Mar 22 14:24:36.18: [25656]: <-- [9:AT+FIE=0\r]
> Mar 22 14:24:36.29: [25656]: --> [2:OK]
> Mar 22 14:24:36.29: [25656]: <-- [23:AT+FCC=1,D,2,2,3,1,0,0\r]
> Mar 22 14:24:36.40: [25656]: --> [2:OK]
> Mar 22 14:24:36.40: [25656]: <-- [25:AT+FLI="+39 999 9999999"\r]
> Mar 22 14:24:36.51: [25656]: --> [2:OK]
> Mar 22 14:24:36.51: [25656]: DIAL 0,0123456789
> Mar 22 14:24:36.51: [25656]: <-- 
> [33:AT+FCC=1,,,,,,,,0;DT0,0123456789\r]
> Mar 22 14:24:58.17: [25656]: --> [4:+FCO]
> Mar 22 14:24:58.17: [25656]: --> [27:+FCI:"          0123456789"]
> Mar 22 14:24:58.17: [25656]: REMOTE CSI "0123456789"
> Mar 22 14:24:58.54: [25656]: --> [22:+FIS:3,3,0,2,1,1,0,4,0]
> Mar 22 14:24:58.54: [25656]: --> [2:OK]
> Mar 22 14:24:58.54: [25656]: REMOTE best rate 9600 bit/s
> Mar 22 14:24:58.54: [25656]: REMOTE max page width 1728 
> pixels in 215 mm
> Mar 22 14:24:58.54: [25656]: REMOTE max unlimited page length
> Mar 22 14:24:58.54: [25656]: REMOTE best vres 7.7 line/mm
> Mar 22 14:24:58.54: [25656]: REMOTE best format 2-D MR
> Mar 22 14:24:58.54: [25656]: REMOTE supports T.30 Annex A, ECM
> Mar 22 14:24:58.54: [25656]: REMOTE best 20 ms, 10 ms/scanline
> Mar 22 14:24:58.54: [25656]: USE 9600 bit/s
> Mar 22 14:24:58.54: [25656]: USE 20 ms, 10 ms/scanline
> Mar 22 14:24:58.54: [25656]: USE error correction mode
> Mar 22 14:24:58.54: [25656]: SEND file "docq/doc16167.ps;41"
> Mar 22 14:24:58.54: [25656]: USE page width 1728 pixels in 215 mm
> Mar 22 14:24:58.54: [25656]: USE unlimited page length
> Mar 22 14:24:58.54: [25656]: USE 7.7 line/mm
> Mar 22 14:24:58.54: [25656]: USE 2-D MR
> Mar 22 14:24:58.54: [25656]: <-- [23:AT+FIS=1,3,0,2,1,1,0,4\r]
> Mar 22 14:24:58.65: [25656]: --> [2:OK]
> Mar 22 14:24:58.65: [25656]: <-- [7:AT+FDT\r]
> Mar 22 14:25:14.94: [25656]: --> [7:+FHS:25]
> Mar 22 14:25:14.94: [25656]: REMOTE HANGUP: DCS sent 3 times 
> without response (code 25)
> Mar 22 14:25:14.94: [25656]: --> [2:OK]
> Mar 22 14:28:14.94: [25656]: MODEM <Timeout>
> Mar 22 14:28:14.94: [25656]: SEND: DCS sent 3 times without 
> response; Giving up after 3 attempts to send same page 
> "docq/doc16167.ps;41", dirnum 0
> Mar 22 14:28:14.94: [25656]: <-- [5:ATH0\r]
> Mar 22 14:28:15.07: [25656]: --> [2:OK]
> Mar 22 14:28:15.07: [25656]: sched policy=0, priority=0
> Mar 22 14:28:15.07: [25656]: SESSION END
> -- 
> giulioo@xxxxxxxxx
> 
> ____________________ HylaFAX(tm) Users Mailing List 
> _______________________
>   To subscribe/unsubscribe, click 
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe 
> hylafax-users-request@xxxxxxxxxxx < /dev/null
>   *To learn about commercial HylaFAX(tm) support, mail 
> sales@xxxxxxxxx*

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

References:
- [hylafax-users] AT+FDT -> FHS:25 (DCS) errors
  - From: Giulio Orsero

Prev by Date: [hylafax-users] AT+FDT -> FHS:25 (DCS) errors
Next by Date: [hylafax-users] FW: Help Needed
Previous by thread: [hylafax-users] AT+FDT -> FHS:25 (DCS) errors
Next by thread: [hylafax-users] problems with outgoing faxes
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services