mail:/var/spool/fax/etc
# ps -fed |grep fax
fax 2674 1 0 17:55 ? 00:00:00 /usr/sbin/faxq
fax 2677 1 0 17:55 ? 00:00:00 /usr/lib/fax/hfaxd -i hylafax -o 4557 -s
444
fax 3703 1 1 21:55 ? 00:00:00 /usr/lib/fax/faxgetty /dev/ttyS1
root 3705 2488 0 21:55 pts/4 00:00:00 grep fax
===
OK
at+fclass=?
0,1,2.0
Log message:
========
Nov 14 00:30:58.68: [ 2549]: SESSION BEGIN
00000052 16147512018
Nov 14 00:30:58.68: [ 2549]: HylaFAX (tm) Version 4.1.7
Nov 14 00:30:58.68: [ 2549]: SEND FAX: JOB
18 DEST 7512018 COMMID 00000052 DEVICE '/dev/ttyS1'
Nov 14 00:30:58.68: [ 2549]: MODEM set DTR
OFF
Nov 14 00:30:58.68: [ 2549]: DELAY 75 ms
Nov 14 00:30:58.75: [ 2549]: MODEM set DTR ON
Nov 14 00:30:58.75: [ 2549]: DELAY 2600 ms
Nov 14 00:31:02.35: [ 2549]: MODEM set baud
rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
Nov 14 00:31:02.35: [ 2549]: DELAY 10 ms
Nov 14 00:31:02.36: [ 2549]: MODEM flush i/o
Nov 14 00:31:02.36: [ 2549]: <--
[4:ATZ\r]
Nov 14 00:31:02.49: [ 2549]: --> [2:OK]
Nov 14 00:31:02.49: [ 2549]: DELAY 3000 ms
Nov 14 00:31:05.49: [ 2549]: <--
[5:ATE0\r]
Nov 14 00:31:05.62: [ 2549]: --> [2:OK]
Nov 14 00:31:05.62: [ 2549]: <--
[5:ATV1\r]
Nov 14 00:31:05.74: [ 2549]: --> [2:OK]
Nov 14 00:31:05.74: [ 2549]: <--
[7:ATQ0X4\r]
Nov 14 00:31:05.88: [ 2549]: --> [2:OK]
Nov 14 00:31:05.88: [ 2549]: <--
[7:ATS0=0\r]
Nov 14 00:31:06.01: [ 2549]: --> [2:OK]
Nov 14 00:31:06.01: [ 2549]: <--
[7:ATS8=2\r]
Nov 14 00:31:06.15: [ 2549]: --> [2:OK]
Nov 14 00:31:06.15: [ 2549]: <--
[8:ATS7=60\r]
Nov 14 00:31:06.27: [ 2549]: --> [2:OK]
Nov 14 00:31:06.27: [ 2549]: <--
[12:AT&H2&I2&R1\r]
Nov 14 00:31:06.41: [ 2549]: --> [2:OK]
Nov 14 00:31:06.41: [ 2549]: <--
[11:ATS13=1&D2\r]
Nov 14 00:31:06.55: [ 2549]: --> [2:OK]
Nov 14 00:31:06.55: [ 2549]: <--
[6:AT&C1\r]
Nov 14 00:31:06.68: [ 2549]: --> [2:OK]
Nov 14 00:31:06.68: [ 2549]: <--
[12:AT+FCLASS=1\r]
Nov 14 00:31:06.82: [ 2549]: --> [2:OK]
Nov 14 00:31:06.82: [ 2549]: <--
[12:AT+FCLASS=0\r]
Nov 14 00:31:06.96: [ 2549]: --> [2:OK]
Nov 14 00:31:06.96: [ 2549]: <--
[5:ATM0\r]
Nov 14 00:31:07.09: [ 2549]: --> [2:OK]
Nov 14 00:31:07.09: [ 2549]: STATE CHANGE:
RUNNING -> SENDING
Nov 14 00:31:07.09: [ 2549]: MODEM input
buffering enabled
Nov 14 00:31:07.09: [ 2549]: Apply DialString rules to "7512018"
Nov 14 00:31:07.09: [ 2549]: --> return
result "7512018"
Nov 14 00:31:07.09: [ 2549]: <--
[12:AT+FCLASS=1\r]
Nov 14 00:31:07.33: [ 2549]: --> [2:OK]
Nov 14 00:31:07.33: [ 2549]: MODEM set
XON/XOFF/FLUSH: input ignored, output disabled
Nov 14 00:31:07.33: [ 2549]: DIAL 7512018
Nov 14 00:31:07.33: [ 2549]: <--
[12:ATDT7512018\r]
Nov 14 00:31:19.00: [ 2549]: -->
[7:CONNECT]
Nov 14 00:31:19.00: [ 2549]: MODEM input
buffering disabled
Nov 14 00:31:20.02: [ 2549]: -->
HDLC<25:FF C0 02 0E AE 2E A6 CA E6 76 96 16 2E F6 72 04 04
04 04 04
04 04 04
7C F4>
Nov 14 00:31:20.02: [ 2549]: --> [2:OK]
Nov 14 00:31:20.02: [ 2549]: REMOTE CSI
"NothingSetup"
Nov 14 00:31:20.02: [ 2549]: <--
[9:AT+FRH=3\r]
Nov 14 00:31:20.03: [ 2549]: -->
[7:CONNECT]
Nov 14 00:31:20.42: [ 2549]: -->
HDLC<12:FF C8 01 00 77 5F 01 79 03 C0 BC A1>
Nov 14 00:31:20.42: [ 2549]: --> [2:OK]
Nov 14 00:31:20.42: [ 2549]: REMOTE best
rate 14400 bit/s
Nov 14 00:31:20.42: [ 2549]: REMOTE max page
width 2432 pixels in 303 mm
Nov 14 00:31:20.42: [ 2549]: REMOTE max
unlimited page length
Nov 14 00:31:20.42: [ 2549]: REMOTE best vres 7.7 line/mm
Nov 14 00:31:20.42: [ 2549]: REMOTE best
format 2-D MR
Nov 14 00:31:20.42: [ 2549]: REMOTE best 0
ms/scanline
Nov 14 00:31:20.42: [ 2549]: USE 14400 bit/s
Nov 14 00:31:20.42: [ 2549]: USE 0 ms/scanline
Nov 14 00:31:20.42: [ 2549]: SEND file
"docq/doc24.ps;70"
Nov 14 00:31:20.42: [ 2549]: USE page width
1728 pixels in 215 mm
Nov 14 00:31:20.42: [ 2549]: USE unlimited
page length
Nov 14 00:31:20.42: [ 2549]: USE 3.85
line/mm
Nov 14 00:31:20.42: [ 2549]: USE 2-D MR
Nov 14 00:31:20.42: [ 2549]: SEND training
at v.17 14400 bit/s
Nov 14 00:31:20.42: [ 2549]: <--
[9:AT+FTH=3\r]
Nov 14 00:31:20.61: [ 2549]: -->
[7:CONNECT]
Nov 14 00:31:20.62: [ 2549]: <--
HDLC<23:FF C0 C2 0E AE 2E A6 CA E6 76 96 16 2E F6 72 04 04
04 04 04
04 04 04>
Nov 14 00:31:20.62: [ 2549]: <-- data
[23]
Nov 14 00:31:20.62: [ 2549]: <-- data [2]
Nov 14 00:31:20.64: [ 2549]: -->
[7:CONNECT]
Nov 14 00:31:20.64: [ 2549]: <--
HDLC<6:FF C8 C1 00 45 1E>
Nov 14 00:31:20.64: [ 2549]: <-- data [6]
Nov 14 00:31:20.64: [ 2549]: <-- data [2]
Nov 14 00:31:22.57: [ 2549]: --> [2:OK]
Nov 14 00:31:22.57: [ 2549]: <--
[9:AT+FTS=7\r]
Nov 14 00:31:22.64: [ 2549]: --> [2:OK]
Nov 14 00:31:22.64: [ 2549]: MODEM set
XON/XOFF/FLUSH: input interpreted, output disabled
Nov 14 00:31:22.64: [ 2549]: <--
[11:AT+FTM=145\r]
Nov 14 00:31:24.11: [ 2549]: -->
[7:CONNECT]
Nov 14 00:31:24.11: [ 2549]: <-- data
[1024]
Nov 14 00:31:24.11: [ 2549]: <-- data
[1024]
Nov 14 00:31:24.11: [ 2549]: <-- data
[652]
Nov 14 00:31:24.11: [ 2549]: <-- data [2]
Nov 14 00:31:25.60: [ 2549]: --> [2:OK]
Nov 14 00:31:25.60: [ 2549]: MODEM set
XON/XOFF/DRAIN: input ignored, output disabled
Nov 14 00:31:25.60: [ 2549]: <--
[9:AT+FRS=1\r]
Nov 14 00:31:25.62: [ 2549]: --> [2:OK]
Nov 14 00:31:25.62: [ 2549]: <--
[9:AT+FRH=3\r]
Nov 14 00:31:26.00: [ 2549]: -->
[7:CONNECT]
Nov 14 00:31:26.53: [ 2549]: -->
HDLC<5:FF C8 21 57 BE>
Nov 14 00:31:26.53: [ 2549]: --> [2:OK]
Nov 14 00:31:26.53: [ 2549]: TRAINING
succeeded
Nov 14 00:31:26.53: [ 2549]: DELAY 75 ms
Nov 14 00:31:26.61: [ 2549]: <--
[11:AT+FTM=146\r]
Nov 14 00:31:26.85: [ 2549]: -->
[7:CONNECT]
Nov 14 00:31:26.85: [ 2549]: SEND begin page
Nov 14 00:31:26.85: [ 2549]: MODEM set
XON/XOFF/FLUSH: input interpreted, output disabled
Nov 14 00:31:26.86: [ 2549]: <-- data
[1028]
Nov 14 00:31:26.86: [ 2549]: <-- data
[1041]
Nov 14 00:31:26.86: [ 2549]: <-- data
[1032]
Nov 14 00:31:26.86: [ 2549]: <-- data
[1033]
Nov 14 00:32:26.85: [ 2549]: MODEM TIMEOUT:
writing to modem
Nov 14 00:32:26.85: [ 2549]: MODEM WRITE
SHORT: sent 1033, wrote 1010
Nov 14 00:32:26.85: [ 2549]: SENT 21021
bytes of data
Nov 14 00:32:26.86: [ 2549]: SEND end page
Nov 14 00:32:26.86: [ 2549]: MODEM set
XON/XOFF/DRAIN: input ignored, output disabled
Nov 14 00:32:26.86: [ 2549]: <--
[9:AT+FTH=3\r]
Nov 14 00:32:29.40: [ 2549]: --> [0:]
Nov 14 00:32:29.40: [ 2549]: MODEM TIMEOUT:
sending HDLC frame
Nov 14 00:32:29.40: [ 2549]: MODEM input
buffering enabled
Nov 14 00:32:29.41: [ 2549]: <--
[5:ATH0\r]
Nov 14 00:32:34.40: [ 2549]: MODEM TIMEOUT:
reading line from modem
Nov 14 00:32:34.40: [ 2549]: MODEM
<Timeout>
Nov 14 00:32:34.40: [ 2549]: MODEM set DTR OFF
Nov 14 00:32:34.41: [ 2549]: STATE CHANGE:
SENDING -> MODEMWAIT (timeout 5)
Nov 14 00:32:34.41: [ 2549]: SESSION END
Modem Configuration:
#
#
Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem
and XON/XOFF flow control.
#
#
CountryCode: 1
AreaCode: 614
FAXNumber: ""
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: "etc/dialrules"
ServerTracing: 0xFFF
SessionTracing: 0xffffffff
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 0
SpeakerVolume: off
GettyArgs: "-h
%l dx_%s"
LocalIdentifier: "NothingSetup"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From
%%l|%c|Page %%P of %%T"
MaxRecvPages: 50
#
#
#
Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 #
use class 1 interface
ModemRate: 19200 #
rate for DCE-DTE communication
ModemFlowControl: xonxoff #
software flow control
#
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets
modem
ModemSetupDCDCmd: AT&C1 #
setup so DCD reflects carrier (or not)
ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow
control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow
control
ModemResultCodesCmd: ATQ0X4 #
enable result codes
#
ModemMfrQueryCmd: !USR
ModemModelQueryCmd: ATI3
ModemRevQueryCmd: ATI7 #
XXX returns a multi-line result
#
# When
AT+FCLASS=1 is issued the modem automatically switches
# to
software flow control; these parameters let the fax software
# reset
flow control as needed after entering Class 1.
#
Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no flow control
Class1HFLOCmd: AT&H1&I0&R2 # setup modem for hardware flow
control
Class1SFLOCmd: "" #
modem does this automatically
#
# This should resolve "DIS/DTC received 3 times"
errors:
#
Class1ResponseWaitCmd: AT+FRS=1 #
wait after sending TCF for response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or
receiving facsimile.
#
ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0
ModemAnswerCmd: AT+FCLASS=1A #
answer in Class 1
#
# Disables the reporting of bad frames by the modem. This
#
overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd: AT+FNR=1,1,1,0
