|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Failure to receive silence.
Hey,
I installed HylaFAX 4.1.5-190 on a Suse Linux Professional 8.2 System
with Kernel 2.4.20. My modem identifies itself with CL-MD56xx.
Sending a fax from OpenOffice functions very well. Receiving a fax from
the same station fails always with "Failure to receive silence.".
Here is my modem configuration file:
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 1
SessionTracing: 0xffffffff
RecvFileMode: 0644
LogFileMode: 0644
DeviceMode: 0666
RingsBeforeAnswer: 10
SpeakerVolume: medium
GettyArgs: "-h %l dx_%s"
LocalIdentifier: Schaeferhoff
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
ModemType: Class1 # use this to supply a hint
ModemRate: 57600 # rate for DCE-DTE communication
ModemFlowControl: rtscts # XON/XOFF flow control assumed
ModemDialCmd: ATDT%s # T for tone dialing
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT&K0 # disable flow control cmd
ModemHardFlowCmd: AT&K3 # hardware flow control cmd
ModemSoftFlowCmd: AT&K4 # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0 # enable result codes
ModemOnHookCmd: ATH0 # place phone on hook (hangup)
ModemSoftResetCmd: ATZ0 # do soft reset of modem
ModemSoftResetCmdDelay: 3000 # pause after soft reset
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
facsimile
transmit
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
Class1SendMsgDelay: 75 # 75ms delay after training
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
Here are the log-file (<removed by myself> means that I removed this
part before pasting it into this email):
Mar 23 19:40:04.57: [ 1425]: HylaFAX (tm) Version 4.1.5
Mar 23 19:40:04.57: [ 1425]: <-- [4:ATA\r]
Mar 23 19:40:07.71: [ 1425]: --> [7:CONNECT]
Mar 23 19:40:07.71: [ 1425]: ANSWER: FAX CONNECTION DEVICE '/dev/modem'
Mar 23 19:40:07.71: [ 1425]: STATE CHANGE: ANSWERING -> RECEIVING
Mar 23 19:40:07.71: [ 1425]: MODEM input buffering enabled
Mar 23 19:40:07.71: [ 1425]: RECV FAX: begin
Mar 23 19:40:07.71: [ 1425]: RECV FAX: CDPN
Mar 23 19:40:07.72: [ 1425]: MODEM input buffering disabled
Mar 23 19:40:07.72: [ 1425]: <-- HDLC<23:FF C0 02 66 66 F6 16 4E A6 66
A6 86 16 C6 CA 04 04 04 04 04 04 04 04>
Mar 23 19:40:07.72: [ 1425]: <-- data [23]
Mar 23 19:40:07.72: [ 1425]: <-- data [2]
Mar 23 19:40:09.35: [ 1425]: --> [7:CONNECT]
Mar 23 19:40:09.35: [ 1425]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Mar 23 19:40:09.35: [ 1425]: <-- data [10]
Mar 23 19:40:09.35: [ 1425]: <-- data [2]
Mar 23 19:40:09.83: [ 1425]: --> [2:OK]
Mar 23 19:40:09.83: [ 1425]: <-- [9:AT+FRH=3\r]
Mar 23 19:40:10.42: [ 1425]: --> [7:CONNECT]
Mar 23 19:40:12.23: [ 1425]: --> HDLC<25:FF C0 C2 8C 0C CC 4C 0C 4C 04
4C CC 9C 4C 04 9C 2C D4 04 04 04 04 04 3C AC>
Mar 23 19:40:12.23: [ 1425]: --> [2:OK]
Mar 23 19:40:12.23: [ 1425]: REMOTE TSI "<removed by myself"
Mar 23 19:40:12.23: [ 1425]: <-- [9:AT+FRH=3\r]
Mar 23 19:40:12.26: [ 1425]: --> [7:CONNECT]
Mar 23 19:40:12.58: [ 1425]: --> HDLC<12:FF C8 C1 00 47 1F 01 01 01 00
47 93>
Mar 23 19:40:12.58: [ 1425]: --> [2:OK]
Mar 23 19:40:12.58: [ 1425]: REMOTE wants 14400 bit/s
Mar 23 19:40:12.58: [ 1425]: REMOTE wants page width 1728 pixels in 215 mm
Mar 23 19:40:12.58: [ 1425]: REMOTE wants unlimited page length
Mar 23 19:40:12.58: [ 1425]: REMOTE wants 7.7 line/mm
Mar 23 19:40:12.58: [ 1425]: REMOTE wants 2-D MR
Mar 23 19:40:12.58: [ 1425]: RECV training at v.17 14400 bit/s
Mar 23 19:40:12.58: [ 1425]: <-- [11:AT+FRM=145\r]
Mar 23 19:40:14.29: [ 1425]: --> [7:CONNECT]
Mar 23 19:40:15.78: [ 1425]: RECV: TCF 2656 bytes, 0% non-zero, 2645
zero-run
Mar 23 19:40:15.79: [ 1425]: --> [10:NO CARRIER]
Mar 23 19:40:15.79: [ 1425]: DELAY 75 ms
Mar 23 19:40:15.87: [ 1425]: TRAINING succeeded
Mar 23 19:40:15.87: [ 1425]: <-- [9:AT+FTH=3\r]
Mar 23 19:40:16.06: [ 1425]: --> [7:CONNECT]
Mar 23 19:40:16.06: [ 1425]: <-- HDLC<3:FF C8 21>
Mar 23 19:40:16.06: [ 1425]: <-- data [3]
Mar 23 19:40:16.06: [ 1425]: <-- data [2]
Mar 23 19:40:17.34: [ 1425]: --> [2:OK]
Mar 23 19:40:17.34: [ 1425]: MODEM input buffering enabled
Mar 23 19:40:17.34: [ 1425]: <-- [11:AT+FRM=146\r]
Mar 23 19:40:18.43: [ 1425]: --> [7:CONNECT]
Mar 23 19:40:18.43: [ 1425]: RECV: begin page
Mar 23 19:40:26.47: [ 1425]: RECV/CQ: Bad 1D pixel count, row 2316, got
0, expected 1728
Mar 23 19:40:26.47: [ 1425]: RECV/CQ: Bad 1D pixel count, row 2317, got
0, expected 1728
Mar 23 19:40:26.47: [ 1425]: RECV/CQ: Bad 1D pixel count, row 2318, got
0, expected 1728
Mar 23 19:40:26.47: [ 1425]: RECV/CQ: Bad 1D pixel count, row 2319, got
0, expected 1728
Mar 23 19:40:26.47: [ 1425]: RECV/CQ: Bad 1D pixel count, row 2320, got
0, expected 1728
Mar 23 19:40:26.47: [ 1425]: RECV/CQ: Adjusting for RTC found at row 2315
Mar 23 19:40:26.47: [ 1425]: RECV: 2315 total lines, 0 bad lines, 0
consecutive bad lines
Mar 23 19:40:26.47: [ 1425]: RECV: end page
Mar 23 19:40:26.47: [ 1425]: --> [10:NO CARRIER]
Mar 23 19:40:26.47: [ 1425]: MODEM input buffering disabled
Mar 23 19:40:26.47: [ 1425]: <-- [9:AT+FRH=3\r]
Mar 23 19:40:26.54: [ 1425]: --> [7:CONNECT]
Mar 23 19:40:27.81: [ 1425]: --> HDLC<5:FF C8 F4 CC 66>
Mar 23 19:40:27.81: [ 1425]: --> [2:OK]
Mar 23 19:40:27.81: [ 1425]: RECV recv EOP (no more pages or documents)
Mar 23 19:40:27.81: [ 1425]: <-- [9:AT+FRS=7\r]
Mar 23 19:40:57.81: [ 1425]: MODEM TIMEOUT: reading line from modem
Mar 23 19:40:57.81: [ 1425]: MODEM <Timeout>
Mar 23 19:40:57.82: [ 1425]: RECV FAX (00000005): recvq/fax00004.tif
from <removed by myself>, route to <unspecified>, 0 pages in 0:50
Mar 23 19:40:57.83: [ 1425]: RECV FAX: Failure to receive silence.
Mar 23 19:40:57.83: [ 1425]: <-- [9:AT+FTH=3\r]
Mar 23 19:40:57.84: [ 1425]: --> [2:OK]
Mar 23 19:40:57.84: [ 1425]: MODEM input buffering enabled
Mar 23 19:40:57.84: [ 1425]: RECV FAX (00000005): session with <removed
by myself> terminated abnormally: Failure to receive silence.
Mar 23 19:40:57.84: [ 1425]: RECV FAX: bin/faxrcvd "recvq/fax00004.tif"
"modem" "00000005" "Failure to receive silence." "" "" ""
Mar 23 19:40:57.87: [ 1425]: RECV FAX: end
Mar 23 19:40:57.87: [ 1425]: SESSION END
I hope anyone can help me solving this problem.
Thanks
Andreas
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
