[hylafax-users] mgetty not istalled (faxgetty stalls)

[<yidnek@xxxxxxxxxxxx>]

I'm running HylaFax 4.1.8 on RedHat 9.0; USR 56K.
Yesterday I had a problem receiving faxes. When I checked the system log
here is what it looks like:

Feb 25 16:16:14 faxserver FaxGetty[3040]: MODEM U.S. ROBOTICS 56K FAX /
Feb 25 16:34:14 faxserver FaxGetty[3040]: ANSWER: Ring detected without
successful handshake
Feb 25 16:34:29 faxserver FaxGetty[3040]: MODEM U.S. ROBOTICS 56K FAX /
Feb 25 16:38:25 faxserver FaxGetty[3040]: ANSWER: DATA CONNECTION
Feb 25 16:38:25 faxserver FaxGetty[3040]: GETTY: START "/sbin/mgetty -h
/dev/ttyS1 dx_19200", pid 4571
Feb 25 16:38:25 faxserver FaxGetty[3040]: GETTY: exit status 077400

but there is no /sbin/mgetty on the faxserver. Then I thought of installing
mgetty-1.1.30-2.i386.rpm. rpm -qpl shows that mgetty+sendfax will be
installed  but I read in the docs that mgetty+sendfax don't work with
HylaFax.

What should I do?
BTW I want to accept 'fax' calls only, no 'data' calls.

Below is the config.ttyS1 file.

Thanks in advance,
Yidnek

#
# Configuration for using the Class 2.0 command interface
# with a USR v.34 Courier or Sporster modem.
#
# RTS/CTS flow control is used default.
#
#
CountryCode:		1
AreaCode:		295
FAXNumber:		x.xxx.xxx.xxxx
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0666
LogFileMode:		0644
DeviceMode:		0666
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Nothing setup"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		100
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2.0	# use class 2.0 interface
ModemRate:		19200		# DCE-DTE communication rate
ModemFlowControl:	xonxoff
#
ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no flow control
ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for hardware flow control
ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for software flow control
#
ModemSetupDTRCmd:	ATS13=1&D2	# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
ModemResultCodesCmd:	ATQ0X4		# enable extended result codes
#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
ModemSetupAACmd:	AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:	"ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd:		AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd:	!(0),(0)	# override modem response
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0
#
# USR modems violate Class 2.0 specs and do not send RTC itself
#
Class2SendRTC:	yes
#
# +FAP=? not supported on this modem, gives ERROR in ServerTracing
#
Class2APQueryCmd:       none
LockVoiceCalls:		no

ModemReadyState:	B




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*