We have been using succesfully Hylafax V4.0pl1 on Indy and O2 IRIX
6.5.17f.
After upgrading to IRIX 6.5.21f if a receiving FAX was more than 1
page
a 2GB file with just the 1st page and some strange stuff were written.
We tried to move to Origin 200 with the same results.
So we upgraded to SGI Freeware new release, 4.1.2.
With 4.1.2 either on Origin 200 IRIX 6.5.22 or on O2 IRIX 6.5.21f we
have no way to ither send or receive a fax: as soon as the modem
completes the dialogue with the fax and starts reading or writing the
file the programe exits with status 0xa. Last logged line is SEND
begin
page (or RECV).
Nov 04 14:40:26.26: [41122]: DIAL 051578337
Nov 04 14:40:26.26: [41122]: <-- [14:ATDT051578337\r]
Nov 04 14:40:42.16: [41122]: --> [4:+FCO]
Nov 04 14:40:44.86: [41122]: --> [27:+FCI:" +39 051 578337"]
Nov 04 14:40:44.86: [41122]: REMOTE CSI "+39 051 578337"
Nov 04 14:40:44.86: [41122]: --> [20:+FIS:1,5,0,2,1,0,0,0]
Nov 04 14:40:44.86: [41122]: --> [2:OK]
Nov 04 14:40:44.86: [41122]: REMOTE best rate 14400 bit/s
Nov 04 14:40:44.86: [41122]: REMOTE max page width 1728 pixels in 215
mm
Nov 04 14:40:44.86: [41122]: REMOTE max unlimited page length
Nov 04 14:40:44.86: [41122]: REMOTE best vres 7.7 line/mm
Nov 04 14:40:44.86: [41122]: REMOTE best format 2-D MR
Nov 04 14:40:44.86: [41122]: REMOTE best 0 ms/scanline
Nov 04 14:40:44.86: [41122]: USE 14400 bit/s
Nov 04 14:40:44.86: [41122]: USE 0 ms/scanline
Nov 04 14:40:44.87: [41122]: SEND file "docq/doc3.cover;30"
Nov 04 14:40:44.87: [41122]: USE page width 1728 pixels in 215 mm
Nov 04 14:40:44.87: [41122]: USE unlimited page length
Nov 04 14:40:44.87: [41122]: USE 3.85 line/mm
Nov 04 14:40:44.87: [41122]: USE 1-D MR
Nov 04 14:40:44.87: [41122]: <-- [23:AT+FIS=0,5,0,2,0,0,0,0\r]
Nov 04 14:40:45.11: [41122]: --> [2:OK]
Nov 04 14:40:45.11: [41122]: <-- [7:AT+FDT\r]
Nov 04 14:40:45.37: [41122]: --> [20:+FCS:0,5,0,2,0,0,0,0]
Nov 04 14:40:52.47: [41122]: --> [7:CONNECT]
Nov 04 14:40:52.48: [41122]: SEND begin page
Your facsimile job to 051578337 failed because:
Send program terminated abnormally with exit status 0xa
We tuned carefully the package, as using 2D and 14400 let the system
end
the job due to a EMPTY LINE from MODEM as a reply to AT+FRH=3 with
consequent repeated training, as well as using xonxoff on the
receiving
side cause the software to end with a T.30 T1 timeout.
We tested Class1 and Class2.0 with the same results (empty line when
transmitting with a high speed, timeout when receiving at high speed
xonxoff and exit code 0xa when tuned properly).
Is anyone using Hylavax on SGI?
Is anyone able to deliver new 4.1.8 binaries for SGI?
I will be really happy to receive such a Xmas present...
My best regards, Marco Filippi - CADMO
