|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] cid problem
Am Mittwoch, 1. Oktober 2003 18:27 schrieb _ Ramiress:
Hello Amigo,
when you want the cidnumber, take a look at the bin/faxrcvd script
and make it fit to your needs. this script is responsible for the
post-processing after the receiption of a fax. you can easily change it to
your needs.
HIH
-m
> Hello Amigos,
>
> I have some torubles and I hope someone can help.
> At first, sorry for my bad english.
>
> I have
> hylafax version 4.1.5
> us robotics 56k faxmodem
>
> The problem is:
> I need the received cidname und cidnumber from incoming faxes in a log
> file. With the command "faxstat -r" I
> think I get only the cidnumber (or is this the tsi). i.e.
>
> -rw---- 1 14 +42 2682 70471 12:40 fax00989.tif
> -rw---- 1 14 +42 2682 70471 13:09 fax00990.tif
> -rw---- 14 14 +42 2742 47074 13:26 fax00992.tif
> -rw---- 1 14 +42 2683 80481 13:21 fax00993.tif
>
>
> In the ../fax/log I don`t find any hint about the cidname
>
> Oct 01 17:30:36.49: [27058]: SESSION BEGIN 00001278 42150035573
> Oct 01 17:30:36.49: [27058]: HylaFAX (tm) Version 4.1.5
> Oct 01 17:30:36.49: [27058]: <-- [4:ATA\r]
> Oct 01 17:30:43.04: [27058]: --> [4:+FCO]
> Oct 01 17:30:43.04: [27058]: ANSWER: FAX CONNECTION DEVICE '/dev/505'
> Oct 01 17:30:43.04: [27058]: RECV FAX: begin
> Oct 01 17:30:45.02: [27058]: --> [27:+FTI:" +42 2683 80481"]
> Oct 01 17:30:45.02: [27058]: REMOTE TSI "+42 2683 80481"
> Oct 01 17:30:45.02: [27058]: --> [20:+FCS:0,5,0,2,0,0,0,1]
> Oct 01 17:30:45.02: [27058]: REMOTE wants 14400 bit/s
> Oct 01 17:30:45.02: [27058]: REMOTE wants page width 1728 pixels in 215 mm
> Oct 01 17:30:45.02: [27058]: REMOTE wants unlimited page length
> Oct 01 17:30:45.02: [27058]: REMOTE wants 3.85 line/mm
> Oct 01 17:30:45.02: [27058]: REMOTE wants 1-D MR
> Oct 01 17:30:45.02: [27058]: --> [2:OK]
> Oct 01 17:30:45.02: [27058]: <-- [7:AT+FDR\r]
> Oct 01 17:30:50.27: [27058]: --> [7:CONNECT]
> Oct 01 17:30:50.27: [27058]: RECV: begin page
> Oct 01 17:30:50.27: [27058]: RECV: send trigger 022
> Oct 01 17:30:50.27: [27058]: <-- data [1]
> Oct 01 17:31:05.52: [27058]: RECV: 1133 total lines, 0 bad lines, 0
> consecutive bad lines
> Oct 01 17:31:05.52: [27058]: --> [17:+FPS:1,1142,0,0,0]
> Oct 01 17:31:06.74: [27058]: --> [6:+FET:2]
> Oct 01 17:31:06.74: [27058]: RECV recv EOP (no more pages or documents)
> Oct 01 17:31:06.74: [27058]: --> [2:OK]
> Oct 01 17:31:06.74: [27058]: RECV send MCF (message confirmation)
> Oct 01 17:31:06.74: [27058]: RECV FAX (00001278): from +42 2683 80481, page
> 1 in 0:21, INF, 3.85 line
> Oct 01 17:31:06.74: [27058]: RECV FAX (00001278): recvq/fax01005.tif from
> +42 2683 80481, route to <u
> Oct 01 17:31:06.74: [27058]: <-- [7:AT+FDR\r]
> Oct 01 17:31:09.45: [27058]: --> [7:+FHS:00]
> Oct 01 17:31:09.45: [27058]: REMOTE HANGUP: Normal and proper end of
> connection (code 0)
> Oct 01 17:31:09.45: [27058]: RECV FAX: bin/faxrcvd "recvq/fax01005.tif"
> "505" "00001278" "
> Oct 01 17:31:10.15: [27058]: RECV FAX: end
> Oct 01 17:31:10.15: [27058]: SESSION END
>
>
> this is my config.505
>
> # OF THIS SOFTWARE.
> #
>
> #
> # Configuration for using the Class 2.0 command interface
> # with a USR v.34 Courier or Sporster modem.
> #
> # RTS/CTS flow control is used default.
> #
> #
> CountryCode: 42
> AreaCode: 1
> FAXNumber: 50035573
> LongDistancePrefix: 0
> InternationalPrefix: 00
> DialStringRules: etc/dialrules
> ServerTracing: 1
> SessionTracing: 11
> RecvFileMode: 0600
> LogFileMode: 0600
> DeviceMode: 0600
> RingsBeforeAnswer: 4
> CIDNumber: "CIDNUMBER = "
> CIDName: "CIDNAME = "
> #QualifyCID: etc/cid
> #RingFax: RING1
> SpeakerVolume: off
> GettyArgs: "-h %l dx_%s"
> LocalIdentifier: "Test"
> TagLineFont: etc/lutRS18.pcf
> TagLineFormat: "From %%s %%l |%c|Page %%P of %%T"
> MaxRecvPages: 25
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType: Class2.0 # use class 2.0 interface
> ModemRate: 38400 # DCE-DTE communication rate
> ModemFlowControl: rtscts # hardware flow control
> #
> ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
> ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow
> control
> ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow
> control
> #
> ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
> ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or
> not)
> ModemResultCodesCmd: ATQ0X4#CID=1 # enable extended result codes
> #ModemAnswerCMD: ATA
> #
> # NB: adaptive answer only seems to work properly when
> # the modem is left idling in Class 2.0
> #
> ModemSetupAACmd: AT+FAA=1
> #
> # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
> # Note that we both turn the speaker on/off and set volume.
> #
> ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
> #
> # Modem does not support HDLC frame tracing; we add this just
> # to eliminate spurious ERROR results that confuse the naive.
> #
> Class2BUGCmd: AT+FBU=0
> #
> # The modem doesn't support copy quality checking, even though it
> # returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
> # response so that the server will do copy quality checking.
> #
> Class2CQQueryCmd: !(0),(0) # override modem response
> #
> # Disables the reporting of bad frames by the modem. This
> # overcomes a firmware problem in the x2 and V90 Sportsters.
> # It is not necessary for the Courier modem.
> #
> Class2NRCmd: AT+FNR=1,1,1,0
> #
> # USR modems violate Class 2.0 specs and do not send RTC itself
> #
> Class2SendRTC: yes
> #
> # +FAP=? not supported on this modem, gives ERROR in ServerTracing
> #
> Class2APQueryCmd: none
>
>
> I hope you can help me.
>
>
> thank you
> Ramiress
>
> _________________________________________________________________
> MSN Groups & Chat - Freunde finden - leicht gemacht
> http://groups.msn.com/people/
>
>
> ____________________ HylaFAX(tm) Users Mailing List _______________________
> To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
> *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*
--
HAGOS eG phone: +49 711 7880592
Matthias Reich fax: +49 711 7880535
Industriestr. 62 web: http://www.hagos.de
D-70565 Stuttgart mail: rei@xxxxxxxx
Germany
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*
