(no subject)

Aug 27 09:07:21 rxgui-1 FaxQueuer[4343]: [ID 414172 daemon.error] MODEM /dev/cua/a003 appears to be wedged

-Also in /var/spool/hylafax/log -what are the FCS errors? what are the Modem command errors? Just to resolve quickly I just powered off/on the modem. Why would it just get wedged?

Aug 27 09:01:06.21: [ 7533]: SESSION BEGIN 00018462 902124487572

Aug 27 09:01:06.21: [ 7533]: HylaFAX (tm) Version 4.1.2

Aug 27 09:01:06.21: [ 7533]: SEND FAX: JOB 9942 DEST 011902124487572 COMMID 0001

8462 DEVICE '/dev/cua/a003'

Aug 27 09:01:06.21: [ 7533]: DELAY 75 ms

Aug 27 09:01:06.30: [ 7533]: DELAY 2600 ms

Aug 27 09:01:08.90: [ 7533]: <-- [4:ATZ\r]

Aug 27 09:01:09.30: [ 7533]: --> [2:OK]

Aug 27 09:01:09.30: [ 7533]: DELAY 3000 ms

Aug 27 09:01:12.31: [ 7533]: <-- [5:ATE0\r]

Aug 27 09:01:12.49: [ 7533]: --> [2:OK]

Aug 27 09:01:12.49: [ 7533]: <-- [5:ATV1\r]

Aug 27 09:01:12.67: [ 7533]: --> [2:OK]

Aug 27 09:01:12.67: [ 7533]: <-- [7:ATQ0X4\r]

Aug 27 09:01:12.85: [ 7533]: --> [2:OK]

Aug 27 09:01:12.85: [ 7533]: <-- [7:ATS0=0\r]

Aug 27 09:01:13.03: [ 7533]: --> [2:OK]

Aug 27 09:01:13.03: [ 7533]: <-- [7:ATS8=2\r]

Aug 27 09:01:13.21: [ 7533]: --> [2:OK]

Aug 27 09:01:13.21: [ 7533]: <-- [8:ATS7=60\r]

Aug 27 09:01:13.39: [ 7533]: --> [2:OK]

Aug 27 09:01:13.39: [ 7533]: <-- [12:AT&H1&I0&R2\r]

Aug 27 09:01:06.21: [ 7533]: SESSION BEGIN 00018462 902124487572

Aug 27 09:01:06.21: [ 7533]: HylaFAX (tm) Version 4.1.2

Aug 27 09:01:06.21: [ 7533]: SEND FAX: JOB 9942 DEST 011902124487572 COMMID 0001

8462 DEVICE '/dev/cua/a003'

Aug 27 09:01:06.21: [ 7533]: DELAY 75 ms

Aug 27 09:01:06.30: [ 7533]: DELAY 2600 ms

Aug 27 09:01:08.90: [ 7533]: <-- [4:ATZ\r]

Aug 27 09:01:09.30: [ 7533]: --> [2:OK]

Aug 27 09:01:09.30: [ 7533]: DELAY 3000 ms

Aug 27 09:01:12.31: [ 7533]: <-- [5:ATE0\r]

Aug 27 09:01:12.49: [ 7533]: --> [2:OK]

Aug 27 09:01:12.49: [ 7533]: <-- [5:ATV1\r]

Aug 27 09:01:12.67: [ 7533]: --> [2:OK]

Aug 27 09:01:12.67: [ 7533]: <-- [7:ATQ0X4\r]

Aug 27 09:01:12.85: [ 7533]: --> [2:OK]

Aug 27 09:01:12.85: [ 7533]: <-- [7:ATS0=0\r]

Aug 27 09:01:13.03: [ 7533]: --> [2:OK]

Aug 27 09:01:13.03: [ 7533]: <-- [7:ATS8=2\r]

Aug 27 09:01:13.21: [ 7533]: --> [2:OK]

Aug 27 09:01:13.21: [ 7533]: <-- [8:ATS7=60\r]

Aug 27 09:01:13.39: [ 7533]: --> [2:OK]

Aug 27 09:01:13.39: [ 7533]: <-- [12:AT&H1&I0&R2\r]

Aug 27 09:01:47.92: [ 7533]: NSF remote fax equipment: Xerox

Aug 27 09:01:47.92: [ 7533]: <-- [9:AT+FRH=3\r]

Aug 27 09:01:47.99: [ 7533]: --> [7:CONNECT]

Aug 27 09:01:48.64: [ 7533]: --> [2:OK]

Aug 27 09:01:48.64: [ 7533]: REMOTE CSI ""

Aug 27 09:01:48.64: [ 7533]: <-- [9:AT+FRH=3\r]

Aug 27 09:01:48.72: [ 7533]: --> [7:CONNECT]

Aug 27 09:01:49.10: [ 7533]: --> [2:OK]

Aug 27 09:01:49.10: [ 7533]: REMOTE best rate 14400 bit/s

Aug 27 09:01:49.10: [ 7533]: REMOTE max page width 1728 pixels in 215 mm

Aug 27 09:01:49.10: [ 7533]: REMOTE max unlimited page length

Aug 27 09:01:49.10: [ 7533]: REMOTE best vres 7.7 line/mm

Aug 27 09:01:49.10: [ 7533]: REMOTE best format 2-D MMR

Aug 27 09:01:49.10: [ 7533]: REMOTE supports T.30 Annex A, ECM

Aug 27 09:01:49.10: [ 7533]: REMOTE best 5 ms/scanline

Aug 27 09:01:49.10: [ 7533]: USE 9600 bit/s

Aug 27 09:01:49.10: [ 7533]: USE 5 ms/scanline

Aug 27 09:01:49.10: [ 7533]: SEND file "docq/doc9942.cover;31"

Aug 27 09:01:49.10: [ 7533]: USE page width 1728 pixels in 215 mm

Aug 27 09:01:49.10: [ 7533]: USE unlimited page length

Aug 27 09:01:49.10: [ 7533]: USE 7.7 line/mm

Aug 27 09:01:49.10: [ 7533]: USE 1-D MR

Aug 27 09:01:49.10: [ 7533]: SEND training at v.17 9600 bit/s

Aug 27 09:01:49.10: [ 7533]: <-- [9:AT+FTH=3\r]

Aug 27 09:01:49.20: [ 7533]: --> [7:CONNECT]

Aug 27 09:01:49.20: [ 7533]: <-- data [23]

Aug 27 09:01:49.20: [ 7533]: <-- data [2]

Aug 27 09:01:50.96: [ 7533]: --> [7:CONNECT]

Aug 27 09:01:50.96: [ 7533]: <-- data [6]

Aug 27 09:01:50.96: [ 7533]: <-- data [2]

Aug 27 09:01:51.64: [ 7533]: --> [2:OK]

Aug 27 09:01:51.64: [ 7533]: <-- [9:AT+FTS=7\r]

Aug 27 09:01:51.77: [ 7533]: --> [2:OK]

Aug 27 09:01:51.77: [ 7533]: <-- [10:AT+FTM=97\r]

Aug 27 09:01:53.45: [ 7533]: --> [7:CONNECT]

Aug 27 09:01:53.45: [ 7533]: <-- data [1024]

Aug 27 09:01:53.45: [ 7533]: <-- data [776]

Aug 27 09:01:53.45: [ 7533]: <-- data [2]

Aug 27 09:01:55.21: [ 7533]: --> [2:OK]

Aug 27 09:01:55.21: [ 7533]: <-- [9:AT+FRH=3\r]

Aug 27 09:01:56.38: [ 7533]: --> [7:CONNECT]

Aug 27 09:01:58.01: [ 7533]: --> [5:ERROR]

Aug 27 09:01:58.01: [ 7533]: MODEM Command error

Aug 27 09:01:58.01: [ 7533]: FCS error

Aug 27 09:01:58.01: [ 7533]: DELAY 1500 ms

Aug 27 09:02:15.96: [ 7533]: DELAY 1500 ms
Aug 27 09:02:17.47: [ 7533]: SEND training at v.27ter 4800 bit/s
Aug 27 09:02:17.47: [ 7533]: <-- [9:AT+FTH=3\r]
Aug 27 09:02:17.57: [ 7533]: --> [7:CONNECT]
Aug 27 09:02:17.57: [ 7533]: <-- data [23]
Aug 27 09:02:17.57: [ 7533]: <-- data [2]
Aug 27 09:02:19.31: [ 7533]: --> [7:CONNECT]
Aug 27 09:02:19.31: [ 7533]: <-- data [6]
Aug 27 09:02:19.31: [ 7533]: <-- data [2]
Aug 27 09:02:20.01: [ 7533]: --> [2:OK]
Aug 27 09:02:20.01: [ 7533]: <-- [9:AT+FTS=7\r]
Aug 27 09:02:20.14: [ 7533]: --> [2:OK]
Aug 27 09:02:20.14: [ 7533]: <-- [10:AT+FTM=48\r]
Aug 27 09:02:50.15: [ 7533]: MODEM <Timeout>
Aug 27 09:02:50.15: [ 7533]: Problem sending TCF data
Aug 27 09:02:50.15: [ 7533]: <-- [9:AT+FRH=3\r]
Aug 27 09:02:53.26: [ 7533]: --> [0:]
Aug 27 09:02:53.26: [ 7533]: MODEM <Empty line>
Aug 27 09:02:53.26: [ 7533]: <-- data [1]
Aug 27 09:02:53.47: [ 7533]: MODEM <Timeout>
Aug 27 09:02:53.47: [ 7533]: DELAY 1500 ms
Aug 27 09:02:54.98: [ 7533]: SEND training at v.27ter fallback mode 2400 bit/s
Aug 27 09:02:54.98: [ 7533]: <-- [9:AT+FTH=3\r]
Aug 27 09:02:57.54: [ 7533]: Error sending T.30 prologue frames
Aug 27 09:02:57.54: [ 7533]: TRAINING failed
Aug 27 09:02:57.54: [ 7533]: <-- [9:AT+FTH=3\r]
Aug 27 09:03:00.10: [ 7533]: --> [0:]
Aug 27 09:03:00.10: [ 7533]: <-- [5:ATH0\r]
Aug 27 09:03:05.11: [ 7533]: MODEM <Timeout>
Aug 27 09:03:05.11: [ 7533]: SESSION END

Thx....me