|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Failure to train remote modem at 2400 bps or minimum speed
Hi all, I got this error : Failure to train remote modem at 2400 bps or
minimum speed
when try to send a fax from my hylafax server.
I'm using whfc regmon to register a whfc port to print from my MS Word.
Below are the config.ttyS0 and the error log. Hopefully somebody can help.
Thanks,
Keng Heng. Chan
--start etc/config.ttyS0
CountryCode: x
AreaCode: xx
FAXNumber: +xxxxxxxxxx
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: on
GettyArgs: "-h %l dx_%s"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
ModemRate: 19200 # rate for DCE-DTE communication
#ModemFlowControl: rtscts # default
ModemFlowControl: xonxoff # default
#
ModemNoFlowCmd: AT&K0 # setup no flow control
ModemHardFlowCmd: AT&K3 # setup hardware flow control
ModemSoftFlowCmd: AT&K4 # setup software flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or
not)
#
ModemMfrQueryCmd: !Rockwell
ModemModelQueryCmd: !RC288DPi
ModemRevQueryCmd: ATI3 # product information
#
ModemDialCmd: ATDT%s # T for tone dialing
--- end etc/config.ttyS0
---- Transcript of session follows ----
Aug 05 12:41:00.50: [ 3832]: SESSION BEGIN 00000009 xxxxxxxxxxx
Aug 05 12:41:00.50: [ 3832]: HylaFAX (tm) Version 4.1.7
Aug 05 12:41:00.50: [ 3832]: SEND FAX: JOB 8 DEST xxxxxxxxxx COMMID 00000009
DEVICE '/dev/ttyS0'
Aug 05 12:41:00.50: [ 3832]: DELAY 75 ms
Aug 05 12:41:00.57: [ 3832]: DELAY 2600 ms
Aug 05 12:41:04.18: [ 3832]: DELAY 10 ms
Aug 05 12:41:04.19: [ 3832]: <-- [4:ATZ\r]
Aug 05 12:41:04.21: [ 3832]: --> [2:OK]
Aug 05 12:41:04.21: [ 3832]: DELAY 3000 ms
Aug 05 12:41:07.21: [ 3832]: <-- [5:ATE0\r]
Aug 05 12:41:07.22: [ 3832]: --> [2:OK]
Aug 05 12:41:07.22: [ 3832]: <-- [5:ATV1\r]
Aug 05 12:41:07.23: [ 3832]: --> [2:OK]
Aug 05 12:41:07.23: [ 3832]: <-- [5:ATQ0\r]
Aug 05 12:41:07.24: [ 3832]: --> [2:OK]
Aug 05 12:41:07.24: [ 3832]: <-- [7:ATS0=0\r]
Aug 05 12:41:07.25: [ 3832]: --> [2:OK]
Aug 05 12:41:07.25: [ 3832]: <-- [7:ATS8=2\r]
Aug 05 12:41:07.27: [ 3832]: --> [2:OK]
Aug 05 12:41:07.27: [ 3832]: <-- [8:ATS7=60\r]
Aug 05 12:41:07.28: [ 3832]: --> [2:OK]
Aug 05 12:41:07.28: [ 3832]: <-- [6:AT&K4\r]
Aug 05 12:41:07.29: [ 3832]: --> [2:OK]
Aug 05 12:41:07.29: [ 3832]: <-- [6:AT&D2\r]
Aug 05 12:41:07.30: [ 3832]: --> [2:OK]
Aug 05 12:41:07.30: [ 3832]: <-- [6:AT&C1\r]
Aug 05 12:41:07.31: [ 3832]: --> [2:OK]
Aug 05 12:41:07.31: [ 3832]: <-- [12:AT+FCLASS=1\r]
Aug 05 12:41:07.32: [ 3832]: --> [2:OK]
Aug 05 12:41:07.32: [ 3832]: <-- [7:ATL0M1\r]
Aug 05 12:41:07.33: [ 3832]: --> [2:OK]
Aug 05 12:41:07.33: [ 3832]: <-- [12:AT+FCLASS=1\r]
Aug 05 12:41:07.44: [ 3832]: --> [2:OK]
Aug 05 12:41:07.44: [ 3832]: DIAL 0395436874
Aug 05 12:41:07.45: [ 3832]: <-- [15:ATDT0395436874\r]
Aug 05 12:41:13.59: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:14.66: [ 3832]: --> [2:OK]
Aug 05 12:41:14.66: [ 3832]: REMOTE NSF "00 00 11 80 00 8A 49 10 4D 45 41 53
41 54 20 42 52 4F 41 44 43 41 53 54 00 47 00 86 04 30 30 30 30 91 C0 87 02
01 00 01 01 01 01 00 5D"
Aug 05 12:41:14.66: [ 3832]: NSF remote fax equipment: Canon Laser Class
9000 Series
Aug 05 12:41:14.66: [ 3832]: NSF remote station ID: "MEASAT BROADCAST"
Aug 05 12:41:14.66: [ 3832]: <-- [9:AT+FRH=3\r]
Aug 05 12:41:14.67: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:15.07: [ 3832]: --> [2:OK]
Aug 05 12:41:15.07: [ 3832]: REMOTE CSI "xxxxxxxxxxx"
Aug 05 12:41:15.07: [ 3832]: <-- [9:AT+FRH=3\r]
Aug 05 12:41:15.08: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:15.27: [ 3832]: --> [2:OK]
Aug 05 12:41:15.27: [ 3832]: REMOTE best rate 9600 bit/s
Aug 05 12:41:15.27: [ 3832]: REMOTE max page width 1728 pixels in 215 mm
Aug 05 12:41:15.27: [ 3832]: REMOTE max unlimited page length
Aug 05 12:41:15.27: [ 3832]: REMOTE best vres 7.7 line/mm
Aug 05 12:41:15.27: [ 3832]: REMOTE best format 2-D MMR
Aug 05 12:41:15.27: [ 3832]: REMOTE supports T.30 Annex A, ECM
Aug 05 12:41:15.27: [ 3832]: REMOTE best 10 ms/scanline
Aug 05 12:41:15.27: [ 3832]: USE 9600 bit/s
Aug 05 12:41:15.27: [ 3832]: USE 10 ms/scanline
Aug 05 12:41:15.27: [ 3832]: SEND file "docq/doc7.ps;40"
Aug 05 12:41:15.28: [ 3832]: USE page width 1728 pixels in 215 mm
Aug 05 12:41:15.28: [ 3832]: USE unlimited page length
Aug 05 12:41:15.28: [ 3832]: USE 3.85 line/mm
Aug 05 12:41:15.28: [ 3832]: USE 2-D MR
Aug 05 12:41:15.28: [ 3832]: SEND training at v.29 9600 bit/s
Aug 05 12:41:15.28: [ 3832]: <-- [9:AT+FTH=3\r]
Aug 05 12:41:15.35: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:16.07: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:16.23: [ 3832]: --> [2:OK]
Aug 05 12:41:16.24: [ 3832]: <-- [9:AT+FTS=7\r]
Aug 05 12:41:16.28: [ 3832]: --> [2:OK]
Aug 05 12:41:16.28: [ 3832]: <-- [10:AT+FTM=96\r]
Aug 05 12:41:16.30: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:16.63: [ 3832]: --> [2:OK]
Aug 05 12:41:16.63: [ 3832]: <-- [9:AT+FRH=3\r]
Aug 05 12:41:17.18: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:17.55: [ 3832]: --> [2:OK]
Aug 05 12:41:17.55: [ 3832]: SEND training at v.29 7200 bit/s
Aug 05 12:41:17.55: [ 3832]: <-- [9:AT+FTH=3\r]
Aug 05 12:41:17.63: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:18.41: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:18.61: [ 3832]: --> [2:OK]
Aug 05 12:41:18.61: [ 3832]: <-- [9:AT+FTS=7\r]
Aug 05 12:41:18.65: [ 3832]: --> [2:OK]
Aug 05 12:41:18.65: [ 3832]: <-- [10:AT+FTM=72\r]
Aug 05 12:41:18.66: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:19.07: [ 3832]: --> [2:OK]
Aug 05 12:41:19.07: [ 3832]: <-- [9:AT+FRH=3\r]
Aug 05 12:41:19.70: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:20.09: [ 3832]: --> [2:OK]
Aug 05 12:41:20.09: [ 3832]: SEND training at v.27ter 4800 bit/s
Aug 05 12:41:20.09: [ 3832]: <-- [9:AT+FTH=3\r]
Aug 05 12:41:20.17: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:20.86: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:21.04: [ 3832]: --> [2:OK]
Aug 05 12:41:21.04: [ 3832]: <-- [9:AT+FTS=7\r]
Aug 05 12:41:21.09: [ 3832]: --> [2:OK]
Aug 05 12:41:21.09: [ 3832]: <-- [10:AT+FTM=48\r]
Aug 05 12:41:21.11: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:21.65: [ 3832]: --> [2:OK]
Aug 05 12:41:21.65: [ 3832]: <-- [9:AT+FRH=3\r]
Aug 05 12:41:22.44: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:22.83: [ 3832]: --> [2:OK]
Aug 05 12:41:22.83: [ 3832]: SEND training at v.27ter fallback mode 2400
bit/s
Aug 05 12:41:22.83: [ 3832]: <-- [9:AT+FTH=3\r]
Aug 05 12:41:22.88: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:23.53: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:23.66: [ 3832]: --> [2:OK]
Aug 05 12:41:23.66: [ 3832]: <-- [9:AT+FTS=7\r]
Aug 05 12:41:23.70: [ 3832]: --> [2:OK]
Aug 05 12:41:23.70: [ 3832]: <-- [10:AT+FTM=24\r]
Aug 05 12:41:23.72: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:24.42: [ 3832]: --> [2:OK]
Aug 05 12:41:24.42: [ 3832]: <-- [9:AT+FRH=3\r]
Aug 05 12:41:25.09: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:25.48: [ 3832]: --> [2:OK]
Aug 05 12:41:25.48: [ 3832]: TRAINING failed
Aug 05 12:41:25.48: [ 3832]: <-- [9:AT+FTH=3\r]
Aug 05 12:41:25.56: [ 3832]: --> [7:CONNECT]
Aug 05 12:41:26.04: [ 3832]: --> [2:OK]
Aug 05 12:41:26.04: [ 3832]: <-- [5:ATH0\r]
Aug 05 12:41:26.16: [ 3832]: --> [2:OK]
Aug 05 12:41:26.17: [ 3832]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
