|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Incoming Fax always drops from Panasonic fax machine
I have installed Hylafax version 4.1.5-1 from a Mandrake 9.1 binary
distribution. I am using a zoom external V92 3049 modem which supports
class 1 & 2 fax protocols. I have it set up as a class 1 fax. I can
receive faxes perfectly from any fax machine bar my brother's which is a
Panasonic KX F90. To date it has never succeeded and having gone
through the logs and the FAQ and mailing archives for the past few
months, I am stuck. In enclose my config file and log and would be
grateful for any suggestions. I'm afraid I am a newbie in fax protocols
but less so in Linux.
Config.ttyS1
DialStringRules: etc/dialrules.europe
ServerTracing: 11
SessionTracing: 126
RecvFileMode: 0644
LogFileMode: 0644
Logfacility etc/faxserverlog
DeviceMode: 0644
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "J.R. & D.E. Williamson"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
ModemType: Class1 # use this to supply a hint
#ModemRate: 19200 # rate for DCE-DTE communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#ModemFlowControl: RTSCTS # hardware flow control
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data
#
#ModemDialCmd: ATDT%s # T for tone dialing
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem is reset
#ModemAnswerCmd: ATA # use this to answer phone
#ModemNoFlowCmd: AT&K # disable flow control cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd:ATV1 # enable verbose command results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemSoftResetCmdDelay: 3000 # pause after soft reset
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:ATS8=2 # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
Class1SendMsgDelay: 75 # 75ms delay after training
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
Class1RecvAbortOK: 400 # wait 200ms for abort response prev 200
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
#Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
#Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
#Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
Class1TCFMinRun: 200 # min run is 2/3rds of TCF duration
Log
May 25 11:54:51.50: [ 2894]: SESSION BEGIN 00000028 441623400898
May 25 11:54:51.50: [ 2894]: HylaFAX (tm) Version 4.1.5
May 25 11:54:51.50: [ 2894]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
May 25 11:54:51.50: [ 2894]: <-- [4:ATA\r]
May 25 11:55:00.80: [ 2894]: --> [7:CONNECT]
May 25 11:55:00.80: [ 2894]: MODEM input buffering enabled
May 25 11:55:00.80: [ 2894]: RECV FAX: begin
May 25 11:55:00.80: [ 2894]: MODEM input buffering disabled
May 25 11:55:00.80: [ 2894]: <-- HDLC<23:FF C0 02 CE B6 86 96 36 36 96
EA 04 74 A2 74 22 04 64 04 74 4A 74 52>
May 25 11:55:00.80: [ 2894]: <-- data [23]
May 25 11:55:00.80: [ 2894]: <-- data [2]
May 25 11:55:00.83: [ 2894]: --> [7:CONNECT]
May 25 11:55:00.83: [ 2894]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
May 25 11:55:00.83: [ 2894]: <-- data [10]
May 25 11:55:00.83: [ 2894]: <-- data [2]
May 25 11:55:02.04: [ 2894]: --> [2:OK]
May 25 11:55:02.04: [ 2894]: <-- [9:AT+FRH=3\r]
May 25 11:55:02.59: [ 2894]: --> [7:CONNECT]
May 25 11:55:04.27: [ 2894]: --> HDLC<25:FF C0 C2 EC 6C 4C EC 1C AC 04
2C EC 4C 8C 0C 04 04 04 04 18 08 08 09 11 06>
May 25 11:55:04.28: [ 2894]: --> [5:ERROR]
May 25 11:55:04.28: [ 2894]: MODEM Command error
May 25 11:55:04.28: [ 2894]: FCS error
May 25 11:55:04.28: [ 2894]: DELAY 1500 ms
May 25 11:55:05.78: [ 2894]: <-- [9:AT+FTH=3\r]
May 25 11:55:06.65: [ 2894]: --> [7:CONNECT]
May 25 11:55:06.65: [ 2894]: <-- HDLC<23:FF C0 02 CE B6 86 96 36 36 96
EA 04 74 A2 74 22 04 64 04 74 4A 74 52>
May 25 11:55:06.65: [ 2894]: <-- data [23]
May 25 11:55:06.65: [ 2894]: <-- data [2]
May 25 11:55:06.68: [ 2894]: --> [7:CONNECT]
May 25 11:55:06.68: [ 2894]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
May 25 11:55:06.68: [ 2894]: <-- data [10]
May 25 11:55:06.68: [ 2894]: <-- data [2]
May 25 11:55:07.89: [ 2894]: --> [2:OK]
May 25 11:55:07.89: [ 2894]: <-- [9:AT+FRH=3\r]
May 25 11:55:08.16: [ 2894]: --> [7:CONNECT]
May 25 11:55:08.94: [ 2894]: --> HDLC<25:FF C0 02 1C 9C 1C 0C 0C 2C 04
CC 4C 6C 8C 04 04 2C 2C 04 0C 04 04 04 EF A9>
May 25 11:55:08.94: [ 2894]: --> [2:OK]
May 25 11:55:08.94: [ 2894]: <-- [9:AT+FRH=3\r]
May 25 11:55:08.96: [ 2894]: --> [7:CONNECT]
May 25 11:55:09.37: [ 2894]: --> HDLC<15:FF C8 01 04 77 1F 23 01 49 01
01 19 00 97 91>
May 25 11:55:09.37: [ 2894]: --> [2:OK]
May 25 11:55:09.37: [ 2894]: DELAY 1500 ms
May 25 11:55:10.87: [ 2894]: <-- [9:AT+FTH=3\r]
May 25 11:55:11.74: [ 2894]: --> [7:CONNECT]
May 25 11:55:11.74: [ 2894]: <-- HDLC<23:FF C0 02 CE B6 86 96 36 36 96
EA 04 74 A2 74 22 04 64 04 74 4A 74 52>
May 25 11:55:11.74: [ 2894]: <-- data [23]
May 25 11:55:11.74: [ 2894]: <-- data [2]
May 25 11:55:11.77: [ 2894]: --> [7:CONNECT]
May 25 11:55:11.77: [ 2894]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
May 25 11:55:11.77: [ 2894]: <-- data [10]
May 25 11:55:11.77: [ 2894]: <-- data [2]
May 25 11:55:12.98: [ 2894]: --> [2:OK]
May 25 11:55:12.98: [ 2894]: <-- [9:AT+FRH=3\r]
May 25 11:55:13.02: [ 2894]: --> [7:CONNECT]
May 25 11:55:13.48: [ 2894]: --> [5:00 36 E6 10 03]
May 25 11:55:13.49: [ 2894]: --> [5:ERROR]
May 25 11:55:13.49: [ 2894]: MODEM Command error
May 25 11:55:13.49: [ 2894]: FCS error
May 25 11:55:13.49: [ 2894]: DELAY 1500 ms
May 25 11:55:14.99: [ 2894]: <-- [9:AT+FTH=3\r]
May 25 11:55:15.86: [ 2894]: --> [7:CONNECT]
May 25 11:55:15.86: [ 2894]: <-- HDLC<23:FF C0 02 CE B6 86 96 36 36 96
EA 04 74 A2 74 22 04 64 04 74 4A 74 52>
May 25 11:55:15.86: [ 2894]: <-- data [23]
May 25 11:55:15.86: [ 2894]: <-- data [2]
May 25 11:55:15.89: [ 2894]: --> [7:CONNECT]
May 25 11:55:15.89: [ 2894]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
May 25 11:55:15.89: [ 2894]: <-- data [10]
May 25 11:55:15.89: [ 2894]: <-- data [2]
May 25 11:55:17.10: [ 2894]: --> [2:OK]
May 25 11:55:17.10: [ 2894]: <-- [9:AT+FRH=3\r]
May 25 11:55:17.19: [ 2894]: --> [7:CONNECT]
May 25 11:55:18.42: [ 2894]: --> HDLC<5:FF C8 DF 59 6F>
May 25 11:55:18.42: [ 2894]: --> [2:OK]
May 25 11:55:18.42: [ 2894]: RECV FAX: RSPREC error/got DCN
May 25 11:55:18.42: [ 2894]: RECV FAX: end
May 25 11:55:18.42: [ 2894]: SESSION END
Sorry it's a bit long. Thanks in advance
John
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
