|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Error parsing "+FRM" ?????
get the src.rpm
install the src rpm (rpm -ivh hylafax-4.1.5.rh7.src.rpm)
go to /usr/src/redhat/SOURCES
untar the hylafax-4.1.5.tar.gz (tar zxvf hylafax-4.1.5.tar.gz)
copy the patch you downloaded to
/usr/src/redhat/SOURCES/hylafax-4.1.5.tar.gz
cd hylafax-4.1.5/
patch -p0 < whatyounamedthepatchfile
rpmbuild --bb hylafax.spec
you will then have a new rpm to install under /usr/src/redhat/RPMS
install it and you should have no further trouble with the USR modem
hanging...
good luck.
_______________________________________________________________________________________________
"rAcHeL^cY"
<rachelcy@hotmail.com> To: <hylafax-users@hylafax.org>
Sent by: cc:
hylafax-users-bounce@h Subject: Re: [hylafax-users] Error parsing "+FRM" ?????
ylafax.org
04/25/2003 12:18 PM
Sorry, I'm a bit dumb, may i know how to apply those patch?
as in wat command to run and how to run them?
Thanks in advance for any tips and guidances!!!
Rachel Seok
----- Original Message -----
From: "Stuart Herd" <sherd@muscletech.com>
To: <hylafax-users@hylafax.org>
Sent: Friday, April 25, 2003 8:39 PM
Subject: Re: [hylafax-users] Error parsing "+FRM" ?????
>
> there is a bug in the USR firmware >
> you need to add the patch at
> http://bugs.hylafax.org/bugzilla/show_bug.cgi?id=378 and recompile
> _
>
____________________________________________________________________________
___________________
>
>
>
> "Seok See Wai
> (Rachel)" To:
<hylafax-users@hylafax.org>
> <rachelcy@hotmail.com> cc:
> Sent by: Subject:
[hylafax-users] Error parsing "+FRM" ?????
> hylafax-users-bounce@h
> ylafax.org
>
>
> 04/25/2003 12:55 AM
>
>
>
>
>
> Hi, need help urgently...
>
> I'm using hylafax-4.1.5-1rh8 on redhat 8, below is my config.ttyS0:
>
> CountryCode: 6
> AreaCode: 03
> FAXNumber: +92749062
> LongDistancePrefix: 1
> InternationalPrefix: 011
> DialStringRules: etc/dialrules
> #ServerTracing: 1
> ServerTracing: 0xFFF
> #ServerTracing: 1+2+3
> SessionTracing: 11
> RecvFileMode: 0600
> LogFileMode: 0600
> DeviceMode: 0600
> RingsBeforeAnswer: 1
> SpeakerVolume: off
> GettyArgs: "-h %l dx_%s"
> LocalIdentifier: "NothingSetup"
> TagLineFont: etc/lutRS18.pcf
> TagLineFormat: "From %%l|%c|Page %%P of %%T"
> MaxRecvPages: 25
> AdaptiveAnswer: yes
> AnswerRotary: "fax"
> ModemType: Class1 # use this to supply a hint
> ModemRate: 19200 # rate for DCE-DTE communication
> ModemFlowControl: xonxoff # default
> ModemNoFlowCmd: AT&K0 # setup no flow control
> ModemHardFlowCmd: AT&K3 # setup hardware flow control
> ModemSoftFlowCmd: AT&K4 # setup software flow control
> ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
> ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
> ModemMfrQueryCmd: !Rockwell
> ModemModelQueryCmd: !RC288DPi
> ModemRevQueryCmd: ATI3 # product information
> ModemDialCmd: ATDT%s # T for tone dialing
> ModemAnswerCmd: AT+FCLASS=1;A # default is to answer as fax
> ModemSoftResetCmd: ATZ # do soft reset of modem
> ModemSoftResetCmdDelay: 300 # pause after soft reset
> ModemDTRDropDelay: 50
>
>
> and my class1 file:
> ModemType: Class1 # use this to supply a hint
> Class1Cmd: AT+FCLASS=1 # command to enter class 1
> Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
> Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
> Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
> Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before image
> Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
> Class1SendMsgDelay: 75 # 75ms delay after training
> Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
> Class1TrainingRecovery: 1500 # 1.5sec delay after training
> failure
> Class1RecvAbortOK: 200 # wait 200ms for abort response
> Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
> Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident
frames
> Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
> Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
>
> I was testing it usng a normal call-in, when i hear the fax tone, i
> assuming it works,
> but after a few times (say bout 3-5 times) calling to the hylafax, my
modem
> couldn't initialise
> again, and the /var/log/messages file showing some entry like below:
>
> Jan 1 19:51:02 fileserver FaxGetty[2869]: MODEM ROCKWELL RC288DPi/EM3900
> External Modem Patch 9-11 NVM + SIN + MALY + THAI
> Jan 1 19:51:02 fileserver FaxGetty[2869]: <-- [5:ATM0\r]
> Jan 1 19:51:02 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:02 fileserver FaxGetty[2869]: STATE CHANGE: RECEIVING ->
> RUNNING (timeout 30)
> Jan 1 19:51:02 fileserver FaxGetty[2869]: MODEM input buffering disabled
> Jan 1 19:51:06 fileserver FaxGetty[2869]: STATE CHANGE: RUNNING ->
> LISTENING
> Jan 1 19:51:06 fileserver FaxGetty[2869]: MODEM input buffering enabled
> Jan 1 19:51:06 fileserver FaxGetty[2869]: --> [4:RING]
> Jan 1 19:51:06 fileserver FaxGetty[2869]: STATE CHANGE: LISTENING ->
> ANSWERING
> Jan 1 19:51:06 fileserver FaxGetty[2869]: MODEM input buffering enabled
> Jan 1 19:51:13 fileserver FaxGetty[2869]: ANSWER: FAX CONNECTION DEVICE
> '/dev/ttyS0'
> Jan 1 19:51:52 fileserver FaxGetty[2869]: RECV FAX (00000061): from 603
> 2273 5158, page 1 in 0:32, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
> Jan 1 19:51:52 fileserver FaxGetty[2869]: RECV FAX (00000061):
> recvq/fax00060.tif from 603 2273 5158, route to <unspecified>, 1 pages in
> 0:39
> Jan 1 19:51:53 fileserver FaxGetty[2869]: RECV FAX: bin/faxrcvd
> "recvq/fax00060.tif" "ttyS0" "00000061" "" "" ""
> Jan 1 19:51:54 fileserver FaxGetty[2869]: <-- [5:ATH0\r]
> Jan 1 19:51:55 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:55 fileserver FaxGetty[2869]: MODEM set DTR OFF
> Jan 1 19:51:55 fileserver FaxGetty[2869]: MODEM set DTR OFF
> Jan 1 19:51:55 fileserver FaxGetty[2869]: DELAY 50 ms
> Jan 1 19:51:55 fileserver FaxGetty[2869]: MODEM set DTR ON
> Jan 1 19:51:55 fileserver FaxGetty[2869]: DELAY 2600 ms
> Jan 1 19:51:58 fileserver FaxGetty[2869]: MODEM set baud rate: 19200
baud,
> input flow XON/XOFF, output flow XON/XOFF
> Jan 1 19:51:58 fileserver FaxGetty[2869]: DELAY 10 ms
> Jan 1 19:51:58 fileserver FaxGetty[2869]: MODEM flush i/o
> Jan 1 19:51:58 fileserver FaxGetty[2869]: <-- [4:ATZ\r]
> Jan 1 19:51:58 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:58 fileserver FaxGetty[2869]: DELAY 300 ms
> Jan 1 19:51:58 fileserver FaxGetty[2869]: <-- [5:ATE0\r]
> Jan 1 19:51:58 fileserver FaxGetty[2869]: --> [4:ATE0]
> Jan 1 19:51:58 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:58 fileserver FaxGetty[2869]: <-- [5:ATV1\r]
> Jan 1 19:51:58 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:58 fileserver FaxGetty[2869]: <-- [5:ATQ0\r]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [7:ATS0=0\r]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [7:ATS8=2\r]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [8:ATS7=60\r]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [6:AT&K4\r]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [6:AT&D2\r]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [6:AT&C1\r]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [12:AT+FCLASS=?\r]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [14:0,1,1.0,2,8,10]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Data"
> Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Class 1"
> Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Class 2"
> Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Class 1.0"
> Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Voice"
> Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [12:AT+FCLASS=1\r]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM: Mfr Rockwell
> Jan 1 19:52:00 fileserver FaxGetty[2869]: <-- [5:ATI3\r]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [21:EM3900 External Modem]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [34:Patch 9-11 NVM + SIN +
> MALY + THAI]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM: Model RC288DPi
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM: Revision EM3900
External
> Modem Patch 9-11 NVM + SIN + MALY + THAI
> Jan 1 19:52:00 fileserver FaxGetty[2869]: <-- [9:AT+FTM=?\r]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: -->
> [41:3,24,48,72,73,74,96,97,98,121,122,145,146]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [2:OK]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 3.85 line/mm
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 7.7 line/mm
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 2400 bit/s
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 4800 bit/s
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 7200 bit/s
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 9600 bit/s
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 12000 bit/s
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 14400 bit/s
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports page width 1728
> pixels in 215 mm
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports page width 2048
> pixels in 255 mm
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports page width 2432
> pixels in 303 mm
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports A4 page length
> (297 mm)
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports B4 page length
> (364 mm)
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports unlimited page
> length
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 1-D MR
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 2-D MR
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 0 ms/scanline
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 5 ms/scanline
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 10 ms, 5
> ms/scanline
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 10 ms/scanline
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 20 ms, 10
> ms/scanline
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 20 ms/scanline
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 40 ms, 20
> ms/scanline
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 40 ms/scanline
> Jan 1 19:52:00 fileserver FaxGetty[2869]: <-- [9:AT+FRM=?\r]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [4:RING]
> Jan 1 19:52:00 fileserver FaxGetty[2869]: Error parsing "+FRM" query
> response: "OK"
> Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM set DTR OFF
> Jan 1 19:52:00 fileserver FaxGetty[2869]: /dev/ttyS0: Can not initialize
> modem.
> Jan 1 19:52:00 fileserver FaxGetty[2869]: STATE CHANGE: RECEIVING ->
> MODEMWAIT (timeout 30)
>
> Please help!!!
>
> Rachel Seok
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List
_______________________
> To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org <
/dev/null
> *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.
*
>
>
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
