[hylafax-users] Problems Receiving Fax

["Luis Garcia" <informatica@ortoprono.es>]

I am using hylafax-4.1.5-1rh7 on a Red Hat Linux7.2 Server.
Modem: SupraFAXModem V.32bis

 

Setting up was ok and when I receive faxes everything works fine (no
error messages) but when I open the corresponding tiff files later I can
only see the header. The page is only as long as the header line.
So, where is the rest?????

 

This i s the log

 

ene 28 16:49:40.28: [31279]: SESSION BEGIN 00000441 3496351144
ene 28 16:49:40.28: [31279]: HylaFAX (tm) Version 4.1.5
ene 28 16:49:40.28: [31279]: <-- [4:ATA\r]
ene 28 16:49:42.52: [31279]: --> [3:FAX]
ene 28 16:49:42.52: [31279]: DELAY 10 ms
ene 28 16:49:42.53: [31279]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
ene 28 16:49:42.54: [31279]: RECV FAX: begin
ene 28 16:49:48.99: [31279]: --> [5:+FCON]
ene 28 16:49:50.25: [31279]: --> [29:+FTSI: "                    "]
ene 28 16:49:50.25: [31279]: REMOTE TSI ""
ene 28 16:49:50.56: [31279]: --> [22:+FDCS: 0,3,0,2,1,0,0,1]
ene 28 16:49:50.56: [31279]: REMOTE wants 9600 bit/s
ene 28 16:49:50.56: [31279]: REMOTE wants page width 1728 pixels in 215 mm
ene 28 16:49:50.56: [31279]: REMOTE wants unlimited page length
ene 28 16:49:50.56: [31279]: REMOTE wants 3.85 line/mm
ene 28 16:49:50.56: [31279]: REMOTE wants 2-D MR
ene 28 16:49:50.68: [31279]: --> [2:OK]
ene 28 16:49:50.68: [31279]: <-- [7:AT+FDR\r]
ene 28 16:49:52.39: [31279]: --> [5:+FCFR]
ene 28 16:49:54.35: [31279]: --> [22:+FDCS: 0,3,0,2,1,0,0,1]
ene 28 16:49:54.35: [31279]: REMOTE wants 9600 bit/s
ene 28 16:49:54.35: [31279]: REMOTE wants page width 1728 pixels in 215 mm
ene 28 16:49:54.36: [31279]: REMOTE wants unlimited page length
ene 28 16:49:54.36: [31279]: REMOTE wants 3.85 line/mm
ene 28 16:49:54.36: [31279]: REMOTE wants 2-D MR
ene 28 16:49:54.36: [31279]: --> [7:CONNECT]
ene 28 16:49:54.36: [31279]: RECV: begin page
ene 28 16:49:54.36: [31279]: RECV: send trigger 021
ene 28 16:49:54.36: [31279]: <-- data [1]
ene 28 16:50:03.19: [31279]: RECV: 13 total lines, 0 bad lines, 0 consecutive bad lines
ene 28 16:50:03.20: [31279]: --> [17:+FPTS: 1,2219,0,0]
ene 28 16:50:03.93: [31279]: --> [7:+FET: 2]
ene 28 16:50:03.93: [31279]: RECV recv EOP (no more pages or documents)
ene 28 16:50:04.04: [31279]: --> [2:OK]
ene 28 16:50:04.04: [31279]: RECV send MCF (message confirmation)
ene 28 16:50:04.05: [31279]: RECV FAX (00000441): from , page 1 in 0:14, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
ene 28 16:50:04.05: [31279]: RECV FAX (00000441): recvq/fax00019.tif from , route to <unspecified>, 1 pages in 0:22
ene 28 16:50:04.05: [31279]: <-- [7:AT+FDR\r]
ene 28 16:50:07.14: [31279]: --> [8:+FHNG: 0]
ene 28 16:50:07.14: [31279]: REMOTE HANGUP: Normal and proper end of connection (code 0)
ene 28 16:50:07.15: [31279]: RECV FAX: bin/faxrcvd "recvq/fax00019.tif" "ttyS0" "00000441" "" "" ""
ene 28 16:50:24.66: [31279]: RECV FAX: end
ene 28 16:50:24.66: [31279]: SESSION END

And this is the fax received is attached in the e-mail:

 

 

Does anyone have a clue what the problem is here?

 

Any hint is greatly appreciated

 

Luis Garcia
Valencia (Spain)

 

 

 

fax00019.tif