|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] I get No dial tone
although this is trvial, some phone lines wait a second or so before giving
you an actual dial tone, try modifing the dial string to the following
ATDT,
the "," (comma) adds a one second pause before attempting to dial the phone,
this is very similar to the *70, addition used when dialing into a internet
service provider.
give it a try, it couldn't hurt
joey
----- Original Message -----
From: Frank Sfalanga, Jr. <f.sfalanga@datastorageswfl.net>
To: Sven Jansen <Sven.Jansen@eum.de>; <hylafax-users@hylafax.org>
Sent: Monday, November 25, 2002 6:29 AM
Subject: Re: [hylafax-users] I get No dial tone
> Sven,
>
> Listen very carefully to tell whether the relay on the modem is clicking
> shut when initialized. The AT command set needed to put the modem in
> "ready" state is pretty basic and almost universal to all modems so I
> doubt that's your problem. It's possible, but unlikely. The modem
> might be broken, but that's not likely either.
>
> Another possibility is that you have a telephone system that only
> provides dialtone to its stations - like a PBX or something. With these
> telephone systems the telephone "talks" to the control unit and gets a
> dialtone. Conventional telephones and faxes won't work with these.
>
> Are you testing for dialtone using a cheap $6 phone like the kind you
> could use at home? If a phone like that works (gives you dial tone)
> then the modem should work fine. If you're in a office and the
> telephone you're using is one with lots of buttons on it then that is
> your problem. This kind of phone line won't work for you. You will
> need a dedicated phone line for the fax modem.
>
> - Frank
>
> --------------------------------
>
> Sven Jansen wrote:
>
> >Good Morning,
> >
> >Hey it is monday morning ;-) !!!
> >
> >Yes, we can dial out.
> >It´s possible that are the AT commands incorrect ? But when I start
> >faxsetup hylafax detected my modem autom. and correct !
> >----- Original Message -----
> >From: "Frank Sfalanga, Jr." <f.sfalanga@datastorageswfl.net>
> >To: "Sven Jansen" <Sven.Jansen@eum.de>
> >Sent: Friday, November 22, 2002 6:14 PM
> >Subject: Re: [hylafax-users] I get No dial tone
> >
> >
> >Sven, did you plug a telephone into the phone line and verify that you
> >can dial out?
> >
> >- Frank
> >
> >------------------------------------
> >
> >Sven Jansen wrote:
> >
> >
> >
> >>Hi,
> >>
> >>I install:
> >>Hylafax 4.1.5 with gcc2.95.2 and GNU Make version 3.78.1 on Solaris 8
x86
> >>
> >>Can anybody tell me whats going on here.
> >>I searche in google but maybe i´m stupid .... ????
> >>Why get I this message- PAGE FAILED: No local dialtone
> >>My modem is a US Robotics Vi and Hylafax detect it - I´m sure !!!!!!!!
> >>
> >>
> >>Please help me
> >>thanks in advance
> >>
> >>
> >>Nov 22 17:49:56.71: [17831]: SESSION BEGIN 00000002 49213101771167
> >>Nov 22 17:49:56.71: [17831]: HylaFAX (tm) Version 4.1.5
> >>Nov 22 17:49:56.71: [17831]: SEND PAGE: JOB 2 DEST 01771167 COMMID
> >>00000002
> >>Nov 22 17:49:56.71: [17831]: DELAY 75 ms
> >>Nov 22 17:49:56.80: [17831]: DELAY 2600 ms
> >>Nov 22 17:49:59.41: [17831]: DELAY 10 ms
> >>Nov 22 17:49:59.43: [17831]: <-- [4:ATZ\r]
> >>Nov 22 17:49:59.73: [17831]: --> [3:ATZ]
> >>Nov 22 17:49:59.73: [17831]: --> [2:OK]
> >>Nov 22 17:49:59.73: [17831]: DELAY 3000 ms
> >>Nov 22 17:50:02.74: [17831]: <-- [5:ATE0\r]
> >>Nov 22 17:50:02.90: [17831]: --> [4:ATE0]
> >>Nov 22 17:50:02.90: [17831]: --> [2:OK]
> >>Nov 22 17:50:02.90: [17831]: <-- [5:ATV1\r]
> >>Nov 22 17:50:03.07: [17831]: --> [2:OK]
> >>Nov 22 17:50:03.07: [17831]: <-- [7:ATQ0X4\r]
> >>Nov 22 17:50:03.23: [17831]: --> [2:OK]
> >>Nov 22 17:50:03.23: [17831]: <-- [7:ATS0=0\r]
> >>Nov 22 17:50:03.40: [17831]: --> [2:OK]
> >>Nov 22 17:50:03.40: [17831]: <-- [7:ATS8=2\r]
> >>Nov 22 17:50:03.56: [17831]: --> [2:OK]
> >>Nov 22 17:50:03.56: [17831]: <-- [8:ATS7=60\r]
> >>Nov 22 17:50:03.73: [17831]: --> [2:OK]
> >>Nov 22 17:50:03.73: [17831]: <-- [12:AT&H1&I0&R2\r]
> >>Nov 22 17:50:03.91: [17831]: --> [2:OK]
> >>Nov 22 17:50:03.91: [17831]: <-- [11:ATS13=1&D2\r]
> >>Nov 22 17:50:04.08: [17831]: --> [2:OK]
> >>Nov 22 17:50:04.08: [17831]: <-- [6:AT&C1\r]
> >>Nov 22 17:50:04.24: [17831]: --> [2:OK]
> >>Nov 22 17:50:04.24: [17831]: <-- [5:ATM0\r]
> >>Nov 22 17:50:04.41: [17831]: --> [2:OK]
> >>Nov 22 17:50:04.41: [17831]: <-- [12:AT+FCLASS=0\r]
> >>Nov 22 17:50:04.56: [17831]: --> [2:OK]
> >>Nov 22 17:50:04.56: [17831]: DIAL 01771167
> >>Nov 22 17:50:04.56: [17831]: <-- [13:ATDT01771167\r]
> >>Nov 22 17:50:20.92: [17831]: --> [12:NO DIAL TONE]
> >>Nov 22 17:50:20.92: [17831]: PAGE FAILED: No local dialtone
> >>Nov 22 17:50:20.92: [17831]: <-- [5:ATH0\r]
> >>Nov 22 17:50:21.18: [17831]: --> [2:OK]
> >>Nov 22 17:50:21.18: [17831]: SESSION END
> >>
> >>
> >>
> >>
> >>
> >>
> >>Mit freundlichen Grüssen
> >>
> >>Sven Jansen
> >>--
> >>Technik Sven.Jansen@eum.de
> >>ebner & martin informationssysteme gmbh http://www.eum.de
> >>Furtherhofstr.1a fon: +49 2131 527393-10
> >>D-41462 Neuss fax: +49 2131 527393-93
> >>
> >>
> >>____________________ HylaFAX(tm) Users Mailing List
> >>
> >>
> >_______________________
> >
> >
> >> To subscribe/unsubscribe, click
> >>
> >>
> >http://lists.hylafax.org/cgi-bin/lsg2.cgi
> >
> >
> >>On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org <
> >>
> >>
> >/dev/null
> >
> >
> >> *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org
> >>
> >>
> >.*
> >
> >
>
>
> ____________________ HylaFAX(tm) Users Mailing List
_______________________
> To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org <
/dev/null
> *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
>
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
