[hylafax-users] Another Phase B/C failure problem

["Jessie Hui" <jeshui@siliconcreation.com>]

Hi,

 

I am a newbie to the hylafax, and I dont know why I have this Phase B/C failure again...

 

Oct 13 19:22:37.68: [26343]: SESSION BEGIN 00000572 85241527526671
Oct 13 19:22:37.68: [26343]: SEND FAX: JOB 277 DEST 27526671 COMMID 00000572
Oct 13 19:22:37.68: [26343]: MODEM set DTR OFF
Oct 13 19:22:37.68: [26343]: DELAY 2600 ms
Oct 13 19:22:40.28: [26343]: MODEM set DTR ON
Oct 13 19:22:40.28: [26343]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS
Oct 13 19:22:40.28: [26343]: MODEM flush i/o
Oct 13 19:22:40.28: [26343]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Oct 13 19:22:40.42: [26343]: --> [2:OK]
Oct 13 19:22:40.42: [26343]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
Oct 13 19:22:40.56: [26343]: --> [2:OK]
Oct 13 19:22:40.56: [26343]: <-- [14:AT+FCLASS=2.0\r]
Oct 13 19:22:40.70: [26343]: --> [2:OK]
Oct 13 19:22:40.70: [26343]: <-- [9:AT+FLO=2\r]
Oct 13 19:22:40.84: [26343]: --> [2:OK]
Oct 13 19:22:40.84: [26343]: <-- [9:AT+FPP=0\r]
Oct 13 19:22:40.98: [26343]: --> [2:OK]
Oct 13 19:22:40.98: [26343]: <-- [9:AT+FBO=0\r]
Oct 13 19:22:41.12: [26343]: --> [2:OK]
Oct 13 19:22:41.12: [26343]: <-- [10:AT+FCT=30\r]
Oct 13 19:22:41.26: [26343]: --> [2:OK]
Oct 13 19:22:41.26: [26343]: <-- [15:AT+FNR=1,1,1,0\r]
Oct 13 19:22:41.40: [26343]: --> [2:OK]
Oct 13 19:22:41.40: [26343]: <-- [9:AT+FIE=0\r]
Oct 13 19:22:41.54: [26343]: --> [2:OK]
Oct 13 19:22:41.54: [26343]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Oct 13 19:22:41.68: [26343]: --> [2:OK]
Oct 13 19:22:41.68: [26343]: <-- [5:ATM0\r]
Oct 13 19:22:41.81: [26343]: --> [2:OK]
Oct 13 19:22:41.81: [26343]: MODEM input buffering enabled
Oct 13 19:22:41.81: [26343]: <-- [14:AT+FCLASS=2.0\r]
Oct 13 19:22:42.05: [26343]: --> [2:OK]
Oct 13 19:22:42.05: [26343]: <-- [9:AT+FLO=2\r]
Oct 13 19:22:42.29: [26343]: --> [2:OK]
Oct 13 19:22:42.29: [26343]: <-- [9:AT+FPP=0\r]
Oct 13 19:22:42.53: [26343]: --> [2:OK]
Oct 13 19:22:42.53: [26343]: <-- [9:AT+FBO=0\r]
Oct 13 19:22:42.77: [26343]: --> [2:OK]
Oct 13 19:22:42.77: [26343]: <-- [10:AT+FCT=30\r]
Oct 13 19:22:43.01: [26343]: --> [2:OK]
Oct 13 19:22:43.01: [26343]: <-- [15:AT+FNR=1,1,1,0\r]
Oct 13 19:22:43.25: [26343]: --> [2:OK]
Oct 13 19:22:43.25: [26343]: <-- [9:AT+FIE=0\r]
Oct 13 19:22:43.49: [26343]: --> [2:OK]
Oct 13 19:22:43.49: [26343]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Oct 13 19:22:43.73: [26343]: --> [2:OK]
Oct 13 19:22:43.73: [26343]: <-- [22:AT+FLI="www.mango.cc"\r]
Oct 13 19:22:43.97: [26343]: --> [2:OK]
Oct 13 19:22:43.97: [26343]: DIAL 27526671
Oct 13 19:22:43.97: [26343]: <-- [13:ATDT27526671\r]
Oct 13 19:23:11.53: [26343]: --> [4:+FCO]
Oct 13 19:23:14.73: [26343]: --> [27:+FCI:"            27526671"]
Oct 13 19:23:14.73: [26343]: REMOTE CSI "27526671"
Oct 13 19:23:14.73: [26343]: --> [20:+FIS:1,3,0,2,1,0,0,4]
Oct 13 19:23:14.73: [26343]: --> [2:OK]
Oct 13 19:23:14.73: [26343]: REMOTE best rate 9600 bit/s
Oct 13 19:23:14.73: [26343]: REMOTE max page width 1728 pixels in 215 mm
Oct 13 19:23:14.73: [26343]: REMOTE max unlimited page length
Oct 13 19:23:14.73: [26343]: REMOTE best vres 7.7 line/mm
Oct 13 19:23:14.73: [26343]: REMOTE best format 2-D MR
Oct 13 19:23:14.73: [26343]: REMOTE best 20 ms, 10 ms/scanline
Oct 13 19:23:14.73: [26343]: USE 9600 bit/s
Oct 13 19:23:14.73: [26343]: USE 20 ms, 10 ms/scanline
Oct 13 19:23:14.73: [26343]: SEND file "docq/doc277.ps;30"
Oct 13 19:23:14.73: [26343]: USE page width 1728 pixels in 215 mm
Oct 13 19:23:14.73: [26343]: USE unlimited page length
Oct 13 19:23:14.73: [26343]: USE 3.85 line/mm
Oct 13 19:23:14.73: [26343]: USE 1-D MR
Oct 13 19:23:14.73: [26343]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r]
Oct 13 19:23:14.97: [26343]: --> [2:OK]
Oct 13 19:23:14.97: [26343]: <-- [7:AT+FDT\r]
Oct 13 19:23:15.24: [26343]: --> [20:+FCS:0,3,0,2,0,0,0,4]
Oct 13 19:23:20.55: [26343]: --> [5:ERROR]
Oct 13 19:23:20.55: [26343]: MODEM Command error
Oct 13 19:23:20.55: [26343]: <-- [7:AT+FKS\r]
Oct 13 19:23:20.78: [26343]: --> [2:OK]
Oct 13 19:23:20.78: [26343]: SEND: Communication failure during Phase B/C; Giving up after 3 attempts to send same page "docq/doc277.ps;30", dirnum 0
Oct 13 19:23:20.78: [26343]: <-- [5:ATH0\r]
Oct 13 19:23:21.01: [26343]: --> [2:OK]
Oct 13 19:23:21.01: [26343]: MODEM set DTR OFF
Oct 13 19:23:21.01: [26343]: SESSION END

 

If you have any idea, please let me know~~

 

Best regards,

Jessie