Re: [hylafax-users] Hylafax doesn't know what modem to use

[Martin Szymanski <szymanski@nlcom.nl>]

I have created the symbolic link, this is the contents of syslog;

Oct 18 13:13:54 FaxServer FaxSend[905]: /dev/faxCAPI: Can not initialize modem.
Oct 18 13:15:05 FaxServer FaxSend[905]: Unable to setup modem on /dev/faxCAPI; giving up after 2 attempts
Oct 18 13:15:05 FaxServer FaxQueuer[274]: MODEM /dev/faxCAPI appears to be wedged
Oct 18 13:15:05 FaxServer FaxQueuer[274]: MODEM WEDGED: bin/wedged "faxCAPI" "/dev/faxCAPI"
^[[COct 18 13:19:44 FaxServer FaxSend[915]: Syntax error at line 130, missing ':' in "{"
Oct 18 13:19:44 FaxServer FaxSend[915]: Syntax error at line 254, missing ':' in "    {"
Oct 18 13:19:44 FaxServer FaxSend[915]: Syntax error at line 325, missing ':' in "    }"
Oct 18 13:19:44 FaxServer FaxSend[915]: Syntax error at line 326, missing ':' in "}"
Oct 18 13:19:49 FaxServer FaxSend[915]: /dev/faxCAPI: Can not initialize modem.
Oct 18 13:21:00 FaxServer FaxSend[915]: Unable to setup modem on /dev/faxCAPI; giving up after 2 attempts
Oct 18 13:21:00 FaxServer FaxQueuer[274]: MODEM /dev/faxCAPI appears to be wedged
Oct 18 13:21:00 FaxServer FaxQueuer[274]: MODEM WEDGED: bin/wedged "faxCAPI" "/dev/faxCAPI"
Oct 18 13:23:01 FaxServer /USR/SBIN/CRON[926]: (mail) CMD (  if [ -x /usr/sbin/exim -a -f /etc/exim/exim.conf
]; then /usr/sbin/exim -q ; fi)

It seems as faxsend is not compiled correctly, yet I did an apt-get installation, so it should be fine. Does anyone know about this error?

Thanks in advance 
Martin

NLcom
Neuberger & Hughes Distributor & Service Center Benelux
Sint Maartenslaan 26, 6221 AX Maastricht
The Netherlands
Tel: +31 (0)43 3500190
Fax: +31 (0)43 3500192
Web: <http://www.nlcom.nl>
Contact: M. Szymanski
e-mail: szymanski@nlcom.nl
_________________________________________
LiNUX - The choice of the GNU generation
Open Minds. Open Sources. Open Future.



-----Oorspronkelijk bericht-----
Van: Dihor, Viktor [mailto:viktor.dihor@fernwaerme-ulm.de]
Verzonden: vrijdag 18 oktober 2002 11:58
Aan: Martin Szymanski
Onderwerp: AW: [hylafax-users] Hylafax doesn't know what modem to use


HI Martin,

it's my fault.

I have forgotten to mention, that you have to do a sysmlink from /dev/capi20
to /dev/faxCAPI.
Don't forget to put the needed rights for /dev/faxCAPI20.

-----Ursprüngliche Nachricht-----
Von: Martin Szymanski [mailto:szymanski@nlcom.nl]
Gesendet: Freitag, 18. Oktober 2002 11:10
An: 'Lothar Krauss'
Cc: hylafax-users@hylafax.org
Betreff: Re: [hylafax-users] Hylafax doesn't know what modem to use


I have done a clean installation of the system installint debian all over
again. 
I then installed the Fritz Capi drivers wich work fine. I apt-get
hylafax-server and all neccecery software. 

After installing Capi4hylafax i get this message in the syslog

Oct 18 10:59:04 FaxServer FaxSend[443]: /dev/faxCAPI: Can not open modem (No
suc
h file or directory)

am I missing something?

NLcom
Neuberger & Hughes Distributor & Service Center Benelux
Sint Maartenslaan 26, 6221 AX Maastricht
The Netherlands
Tel: +31 (0)43 3500190
Fax: +31 (0)43 3500192
Web: <http://www.nlcom.nl>
Contact: M. Szymanski
e-mail: szymanski@nlcom.nl
_________________________________________
LiNUX - The choice of the GNU generation
Open Minds. Open Sources. Open Future.



-----Oorspronkelijk bericht-----
Van: hylafax-users-bounce@hylafax.org
[mailto:hylafax-users-bounce@hylafax.org]Namens Lothar Krauss
Verzonden: donderdag 17 oktober 2002 21:28
Aan: Martin Szymanski;hylafax-users@hylafax.org
Onderwerp: Re: [hylafax-users] Hylafax doesn't know what modem to use


Hello Martin,

your error message is really interesting. I've checked two servers
where I installed capi4hylafax (one SuSE72, one SuSE8.0), and I did not
found a
libfaxutil.so there, and c2faxrecv does not need it.

I think the best way is to use the binary from
ftp://ftp.avm.de/tools/capi4hylafax.linux without compiling it yourself, as
Viktor suggested. After unpacking the tar file you should only need to call
"./install".

Good Luck

Lothar

Am Don, 17 Okt 2002 schrieb Martin Szymanski: > Hello Lothar,
> 
> I've installed the driver and CAPI4Hylafax yet my inittab is empty. 
> Running the command 
> 
> /usr/local/bin/c2faxrecv -q "/var/spool/fax" &
> 
> results in this message:
> 
>  error while loading shared libraries: libfaxutil.so: cannot open shared
object file: No such file or directory
> 
> faxstat does _not_ report the faxmodem to be ready only this:
> 
> HylaFAX scheduler on FaxServer.intra.nlcom.nl: Running
> 
> do you know how this error is caused?
> 
> Than you very much
> 
> Martin
> 

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*