|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Hylafax 4.1.3, OSX 10.2.1 (Jaguar), Mac G3 B&W, Internal Modem
Even using Class 2 with RTSCTS I have problems illustrated below:
Darwin dualg4 6.1 Darwin Kernel Version 6.1: Fri Sep 6 23:24:34 PDT
2002;
root:xnu/xnu-344.2.obj~2/RELEASE_PPC Power Macintosh powerpcOct 14
15:37:53.18: [10089]: MODEM input buffering enabled
Oct 14 15:37:53.18: [10089]: <-- [12:AT+FCLASS=2\r]
Oct 14 15:37:53.32: [10089]: --> [2:OK]
Oct 14 15:37:53.32: [10089]: <-- [10:AT+FTBC=0\r]
Oct 14 15:37:53.47: [10089]: --> [2:OK]
Oct 14 15:37:53.47: [10089]: <-- [10:AT+FBOR=0\r]
Oct 14 15:37:53.62: [10089]: --> [2:OK]
Oct 14 15:37:53.62: [10089]: <-- [13:AT+FPHCTO=30\r]
Oct 14 15:38:23.62: [10089]: MODEM TIMEOUT: reading line from modem
Oct 14 15:38:23.62: [10089]: MODEM <Timeout>
Oct 14 15:38:23.62: [10089]: <-- [10:AT+FBUG=1\r]
Oct 14 15:38:23.77: [10089]: --> [2:OK]
Oct 14 15:38:23.77: [10089]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Oct 14 15:38:23.93: [10089]: --> [2:OK]
It's very bizarre.
Lee.
On 2002.10.02 13:20 Bob Beaton wrote:
> Chris & Lee,
>
> Thank you for the very helpful and prompt comments. Changing the
> handshake
> mode from xon/xoff to rts/cts and, then, restarting faxgetty worked
> nicely.
>
> For completeness in the list archive, I simply edited one line in my
> /var/spool/hylafax/etc/config.cu.modem file to be:
>
> ModemFlowControl: rtscts # hw flow control (xonxoff is
> default)
>
> With this change and faxgetty restart (kill -HUP <faxgetty PID>), I
> was able
> to use sendfax without a problem. I have not tested receiving a fax
> yet,
> however.
>
> Many thanks again!
> Bob
>
> On 10/2/02 9:37 AM, "cbain" <cbain@acordex.com> wrote:
>
> > Bob,
> >
> > I have gotten Hylafax 4.1.2 to work using the internal modem on Mac
> OS X
> > 10.1.5 and 10.2. I configured the modem as an internal modem using
> class
> > 2 with the additional changes in the config.cu.modem files as
> follows:
> >
> > ModemFlowControl: rtscts # was XON/XOFF flow control
> > ModemSetupDTRCmd: AT&D3 # setup so DTR drop resets
> modem
> > Class2RecvDataTrigger: "\022" # character sent to modem to
> > start recv
> > Class2XmitWaitForXON: no # if true, wait for XON
> before
> > send
> >
> >
> > The Class2XmitWaitForXON when set to yes caused the modem to hang
> when
> > sending, the
> > ModemFlowControl was xonxoff and this caused errors in sending and
> > receiving faxes. I am not sure if the other two changes made any
> > difference, I just made them base on the differences between the
> > RockWell-K56 and the class 2 modem. With these configuration changes
> I
> > can now send and recieve faxes fine with the internal modem.
> >
> > Chris
> >
> >> Hi,
> >>
> >> I compiled and installed the latest HylaFAX on my G3 B&W, which is
> running
> >> the latest Mac OSX. Everything went fine (thanks to the on-line
> HOW-TO and
> >> list comments!!!) until I sent my first fax. As documented in the
> list
> >> archives, there appears to be some time-out problems with the Apple
> internal
> >> modem. I set mine up as a Class 2 modem, using /dev/cu.modem.
> >>
> >> I'm wondering of any fixes have been found for this configuration.
> And, more
> >> generally, I'm wondering if HylaFAX really works with the latest
> OSX. If so,
> >> with what configurations? I have an old 28.8 SupraFaxModem--should
> I be
> >> using that instead of the internal Apple (Rockwell) modem?
> >>
> >> I've attached my log print-out just in case someone's interested
> and far
> >> more intelligent than me with finding my actual problem.
> >>
> >> Many thanks for any comments!
> >>
> >> Bob
> >>
> >> ****
> >>
> >> Oct 02 01:19:53.55: [ 789]: SESSION BEGIN 00000004 13055774370
> >> Oct 02 01:19:53.55: [ 789]: HylaFAX (tm) Version 4.1.3
> >> Oct 02 01:19:53.55: [ 789]: SEND FAX: JOB 2 DEST 1-305-577-4370
> COMMID
> >> 00000004 DEVICE '/dev/cu.modem'
> >> Oct 02 01:19:53.55: [ 789]: DELAY 75 ms
> >> Oct 02 01:19:53.63: [ 789]: DELAY 2600 ms
> >> Oct 02 01:19:57.51: [ 789]: <-- [4:ATZ\r]
> >> Oct 02 01:20:00.67: [ 789]: --> [2:OK]
> >> Oct 02 01:20:00.67: [ 789]: DELAY 3000 ms
> >> Oct 02 01:20:03.67: [ 789]: <-- [5:ATE0\r]
> >> Oct 02 01:20:03.72: [ 789]: --> [4:ATE0]
> >> Oct 02 01:20:03.72: [ 789]: --> [2:OK]
> >> Oct 02 01:20:03.72: [ 789]: <-- [5:ATV1\r]
> >> Oct 02 01:20:03.76: [ 789]: --> [2:OK]
> >> Oct 02 01:20:03.76: [ 789]: <-- [5:ATQ0\r]
> >> Oct 02 01:20:03.81: [ 789]: --> [2:OK]
> >> Oct 02 01:20:03.81: [ 789]: <-- [7:ATS0=0\r]
> >> Oct 02 01:20:03.85: [ 789]: --> [2:OK]
> >> Oct 02 01:20:03.85: [ 789]: <-- [7:ATS8=2\r]
> >> Oct 02 01:20:03.89: [ 789]: --> [2:OK]
> >> Oct 02 01:20:03.90: [ 789]: <-- [8:ATS7=60\r]
> >> Oct 02 01:20:03.95: [ 789]: --> [2:OK]
> >> Oct 02 01:20:03.95: [ 789]: <-- [6:AT&K4\r]
> >> Oct 02 01:20:03.98: [ 789]: --> [2:OK]
> >> Oct 02 01:20:03.98: [ 789]: <-- [6:AT&D3\r]
> >> Oct 02 01:20:04.03: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.03: [ 789]: <-- [6:AT&C1\r]
> >> Oct 02 01:20:04.07: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.07: [ 789]: <-- [12:AT+FCLASS=2\r]
> >> Oct 02 01:20:04.12: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.12: [ 789]: <-- [10:AT+FTBC=0\r]
> >> Oct 02 01:20:04.16: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.16: [ 789]: <-- [10:AT+FBOR=0\r]
> >> Oct 02 01:20:04.20: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.20: [ 789]: <-- [13:AT+FPHCTO=30\r]
> >> Oct 02 01:20:04.25: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.25: [ 789]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
> >> Oct 02 01:20:04.29: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.29: [ 789]: <-- [5:ATM0\r]
> >> Oct 02 01:20:04.34: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.36: [ 789]: <-- [12:AT+FCLASS=2\r]
> >> Oct 02 01:20:04.48: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.48: [ 789]: <-- [10:AT+FTBC=0\r]
> >> Oct 02 01:20:04.63: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.63: [ 789]: <-- [10:AT+FBOR=0\r]
> >> Oct 02 01:20:04.80: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.80: [ 789]: <-- [13:AT+FPHCTO=30\r]
> >> Oct 02 01:20:04.95: [ 789]: --> [2:OK]
> >> Oct 02 01:20:04.95: [ 789]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
> >> Oct 02 01:20:05.24: [ 789]: --> [2:OK]
> >> Oct 02 01:20:05.24: [ 789]: <-- [18:AT+FLID="HF Shop"\r]
> >> Oct 02 01:20:05.39: [ 789]: --> [2:OK]
> >> Oct 02 01:20:05.39: [ 789]: DIAL 13055774370
> >> Oct 02 01:20:05.39: [ 789]: <-- [16:ATDT13055774370\r]
> >> Oct 02 01:20:23.28: [ 789]: --> [5:+FCON]
> >> Oct 02 01:20:25.31: [ 789]: --> [22:+FDIS: 1,5,0,2,1,0,0,0]
> >> Oct 02 01:20:25.31: [ 789]: --> [2:OK]
> >> Oct 02 01:20:25.31: [ 789]: REMOTE best rate 14400 bit/s
> >> Oct 02 01:20:25.31: [ 789]: REMOTE max page width 1728 pixels in
> 215 mm
> >> Oct 02 01:20:25.31: [ 789]: REMOTE max unlimited page length
> >> Oct 02 01:20:25.31: [ 789]: REMOTE best vres 7.7 line/mm
> >> Oct 02 01:20:25.31: [ 789]: REMOTE best format 2-D MR
> >> Oct 02 01:20:25.32: [ 789]: REMOTE best 0 ms/scanline
> >> Oct 02 01:20:25.32: [ 789]: USE 14400 bit/s
> >> Oct 02 01:20:25.32: [ 789]: USE 0 ms/scanline
> >> Oct 02 01:20:25.32: [ 789]: SEND file "docq/doc3.ps;31"
> >> Oct 02 01:20:25.32: [ 789]: USE page width 1728 pixels in 215 mm
> >> Oct 02 01:20:25.32: [ 789]: USE unlimited page length
> >> Oct 02 01:20:25.32: [ 789]: USE 7.7 line/mm
> >> Oct 02 01:20:25.32: [ 789]: USE 1-D MR
> >> Oct 02 01:20:25.32: [ 789]: <-- [24:AT+FDIS=1,5,0,2,0,0,0,0\r]
> >> Oct 02 01:20:25.48: [ 789]: --> [2:OK]
> >> Oct 02 01:20:25.48: [ 789]: <-- [7:AT+FDT\r]
> >> Oct 02 01:20:33.62: [ 789]: --> [22:+FDCS: 1,5,0,2,0,0,0,0]
> >> Oct 02 01:20:33.62: [ 789]: --> [7:CONNECT]
> >> Oct 02 01:20:33.62: [ 789]: SEND wait for XON
> >> Oct 02 01:20:43.62: [ 789]: <-- [6:AT+FK\r]
> >> Oct 02 01:21:13.62: [ 789]: MODEM <Timeout>
> >> Oct 02 01:21:13.62: [ 789]: SEND: Communication failure during
> Phase B/C;
> >> Giving up after 3 attempts to send same page "docq/doc3.ps;31",
> dirnum 0
> >> Oct 02 01:21:13.63: [ 789]: <-- [5:ATH0\r]
> >> Oct 02 01:21:13.78: [ 789]: --> [9:+FHNG: 50]
> >> Oct 02 01:21:13.78: [ 789]: REMOTE HANGUP: Unspecified Transmit
> Phase D
> >> error, including +FPHCTO timeout between data and +FET command
> (code 50)
> >> Oct 02 01:21:15.60: [ 789]: --> [2:OK]
> >> Oct 02 01:21:15.85: [ 789]: SESSION END
> >>
> >> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
> >> To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> >> On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org <
> /dev/null
> >> *To learn about commercial HylaFAX(tm) support, mail
> sales@hylafax.org.*
> >>
> >
> > ____________________ HylaFAX(tm) Users Mailing List
> _______________________
> > To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> > On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org <
> /dev/null
> > *To learn about commercial HylaFAX(tm) support, mail
> sales@hylafax.org.*
> >
>
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
> To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org <
> /dev/null
> *To learn about commercial HylaFAX(tm) support, mail
> sales@hylafax.org.*
>
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
