[hylafax-users] Troubles with Hylafax and Zyxel Omni 56

Hi everyone,

I am having a very hard time getting Hylafax to work with a Zyxel Omni 56 modem. I have tried class 1, 2 and 2.0 settings without success.

I found a configuration sample in this mailinglist. Receiving is now working properly. Sending fails with the following error message:

Unspecified Transmit Phase B error (code 20)

I have included the session logfile below. The modem is currently configured as class 2.0 The system is RedHat 6.2 with the hylafax-4.1.2-1rh6 rpm installed.

Does anyone have a working config example?

Thank you for your help…

Oct 10 09:04:47.29: [16296]: SESSION BEGIN 00000081 310240793684111 Oct 10 09:04:47.29: [16296]: HylaFAX (tm) Version 4.1.2 Oct 10 09:04:47.29: [16296]: SEND FAX: JOB 14 DEST 0793684111 COMMID 00000081 DEVICE '/dev/ttyS0' Oct 10 09:04:47.29: [16296]: DELAY 75 ms Oct 10 09:04:47.37: [16296]: DELAY 2600 ms Oct 10 09:04:49.97: [16296]: <-- [4:ATZ\r] Oct 10 09:04:50.13: [16296]: --> [2:OK] Oct 10 09:04:50.13: [16296]: DELAY 3000 ms Oct 10 09:04:53.13: [16296]: <-- [13:AT&B1s8=6*p3\r] Oct 10 09:04:53.17: [16296]: --> [12:AT&B1s8=6*p3] Oct 10 09:04:53.17: [16296]: --> [2:OK] Oct 10 09:04:53.17: [16296]: <-- [5:ATE0\r] Oct 10 09:04:53.19: [16296]: --> [4:ATE0] Oct 10 09:04:53.19: [16296]: --> [2:OK] Oct 10 09:04:53.19: [16296]: <-- [5:ATV1\r] Oct 10 09:04:53.21: [16296]: --> [2:OK] Oct 10 09:04:53.21: [16296]: <-- [5:ATQ0\r] Oct 10 09:04:53.23: [16296]: --> [2:OK] Oct 10 09:04:53.23: [16296]: <-- [7:ATS0=0\r] Oct 10 09:04:53.25: [16296]: --> [2:OK] Oct 10 09:04:53.25: [16296]: <-- [7:ATS8=2\r] Oct 10 09:04:53.27: [16296]: --> [2:OK] Oct 10 09:04:53.27: [16296]: <-- [8:ATS7=60\r] Oct 10 09:04:53.29: [16296]: --> [2:OK] Oct 10 09:04:53.29: [16296]: <-- [6:AT&D2\r] Oct 10 09:04:53.31: [16296]: --> [2:OK] Oct 10 09:04:53.31: [16296]: <-- [6:AT&C1\r] Oct 10 09:04:53.34: [16296]: --> [2:OK] Oct 10 09:04:53.34: [16296]: <-- [14:AT+FCLASS=2.0\r] Oct 10 09:04:53.37: [16296]: --> [2:OK] Oct 10 09:04:53.37: [16296]: <-- [9:AT+FLO=2\r] Oct 10 09:04:53.40: [16296]: --> [2:OK] Oct 10 09:04:53.40: [16296]: <-- [9:AT+FPP=0\r] Oct 10 09:04:53.44: [16296]: --> [2:OK] Oct 10 09:04:53.44: [16296]: <-- [9:AT+FBO=0\r] Oct 10 09:04:53.48: [16296]: --> [2:OK] Oct 10 09:04:53.48: [16296]: <-- [10:AT+FCT=30\r] Oct 10 09:04:53.51: [16296]: --> [2:OK] Oct 10 09:04:53.51: [16296]: <-- [15:AT+FNR=1,1,1,1\r] Oct 10 09:04:53.54: [16296]: --> [2:OK] Oct 10 09:04:53.54: [16296]: <-- [9:AT+FIE=0\r] Oct 10 09:04:53.57: [16296]: --> [2:OK] Oct 10 09:04:53.57: [16296]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r] Oct 10 09:04:53.61: [16296]: --> [2:OK] Oct 10 09:04:53.61: [16296]: <-- [5:ATM0\r] Oct 10 09:04:53.63: [16296]: --> [2:OK] Oct 10 09:04:53.63: [16296]: <-- [14:AT+FCLASS=2.0\r] Oct 10 09:04:53.76: [16296]: --> [2:OK] Oct 10 09:04:53.76: [16296]: <-- [9:AT+FLO=2\r] Oct 10 09:04:53.89: [16296]: --> [2:OK] Oct 10 09:04:53.89: [16296]: <-- [9:AT+FPP=0\r] Oct 10 09:04:54.02: [16296]: --> [2:OK] Oct 10 09:04:54.02: [16296]: <-- [9:AT+FBO=0\r] Oct 10 09:04:54.16: [16296]: --> [2:OK] Oct 10 09:04:54.16: [16296]: <-- [10:AT+FCT=30\r] Oct 10 09:04:54.30: [16296]: --> [2:OK] Oct 10 09:04:54.30: [16296]: <-- [15:AT+FNR=1,1,1,1\r] Oct 10 09:04:54.44: [16296]: --> [2:OK] Oct 10 09:04:54.44: [16296]: <-- [9:AT+FIE=0\r] Oct 10 09:04:54.57: [16296]: --> [2:OK] Oct 10 09:04:54.57: [16296]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r] Oct 10 09:04:54.71: [16296]: --> [2:OK] Oct 10 09:04:54.71: [16296]: <-- [24:AT+FLI="Berntsen+Braam"\r] Oct 10 09:04:54.84: [16296]: --> [2:OK] Oct 10 09:04:54.85: [16296]: DIAL 0793684111 Oct 10 09:04:54.85: [16296]: <-- [15:ATDT0793684111\r] Oct 10 09:05:07.66: [16296]: --> [4:+FCO]

Oct 10 09:05:08.04: [16296]: --> [27:+FCI:"Bright "]

Oct 10 09:05:08.04: [16296]: REMOTE CSI "Bright"

Oct 10 09:05:08.04: [16296]: --> [20:+FIS:1,5,1,2,0,0,0,0]

Oct 10 09:05:08.04: [16296]: --> [2:OK]

Oct 10 09:05:08.04: [16296]: REMOTE best rate 14400 bit/s

Oct 10 09:05:08.04: [16296]: REMOTE max page width 2048 pixels in 255 mm Oct 10 09:05:08.04: [16296]: REMOTE max unlimited page length

Oct 10 09:05:08.04: [16296]: REMOTE best vres 7.7 line/mm

Oct 10 09:05:08.04: [16296]: REMOTE best format 1-D MR

Oct 10 09:05:08.04: [16296]: REMOTE best 0 ms/scanline

Oct 10 09:05:08.04: [16296]: USE 14400 bit/s

Oct 10 09:05:08.04: [16296]: USE 0 ms/scanline

Oct 10 09:05:08.04: [16296]: SEND file "docq/doc13.ps;01"

Oct 10 09:05:08.15: [16296]: USE page width 1728 pixels in 215 mm Oct 10 09:05:08.15: [16296]: USE unlimited page length

Oct 10 09:05:08.15: [16296]: USE 7.7 line/mm

Oct 10 09:05:08.15: [16296]: USE 1-D MR

Oct 10 09:05:08.15: [16296]: <-- [23:AT+FIS=1,5,0,2,0,0,0,0\r] Oct 10 09:05:08.29: [16296]: --> [2:OK] Oct 10 09:05:08.29: [16296]: <-- [7:AT+FDT\r] Oct 10 09:05:44.15: [16296]: --> [7:+FHS:20] Oct 10 09:05:44.15: [16296]: REMOTE HANGUP: Unspecified Transmit Phase B error (code 20) Oct 10 09:05:44.15: [16296]: --> [2:OK] Oct 10 09:08:44.15: [16296]: MODEM <Timeout> Oct 10 09:08:44.17: [16296]: <-- [5:ATH0\r] Oct 10 09:08:44.38: [16296]: --> [2:OK] Oct 10 09:08:44.39: [16296]: SESSION END