|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Zyxel
Hi,
When I try to send a fax to hylafax, the server discconect after
receiving the first page ?
Can someone help me with this problem ?
Modem = Zyxel Omni 56K
Class = 2.0
================================================================
HYLAFAX TRANSFER LOG
================================================================
Oct 03 22:17:50.92: [23359]: SESSION BEGIN 00000082 31164262983
Oct 03 22:17:50.92: [23359]: HylaFAX (tm) Version 4.1.3
Oct 03 22:17:50.92: [23359]: <-- [4:ATA\r]
Oct 03 22:18:00.66: [23359]: --> [4:+FCO]
Oct 03 22:18:00.66: [23359]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Oct 03 22:18:00.66: [23359]: RECV FAX: begin
Oct 03 22:18:00.94: [23359]: --> [27:+FTI:" 0164258126"]
Oct 03 22:18:00.94: [23359]: REMOTE TSI "0164258126"
Oct 03 22:18:00.94: [23359]: --> [20:+FCS:0,1,0,2,1,0,0,3]
Oct 03 22:18:00.94: [23359]: REMOTE wants 4800 bit/s
Oct 03 22:18:00.94: [23359]: REMOTE wants page width 1728 pixels in 215
mm
Oct 03 22:18:00.94: [23359]: REMOTE wants unlimited page length
Oct 03 22:18:00.94: [23359]: REMOTE wants 3.85 line/mm
Oct 03 22:18:00.94: [23359]: REMOTE wants 2-D MR
Oct 03 22:18:00.94: [23359]: --> [2:OK]
Oct 03 22:18:00.94: [23359]: <-- [7:AT+FDR\r]
Oct 03 22:18:06.07: [23359]: --> [20:+FCS:0,1,0,2,1,0,0,3]
Oct 03 22:18:06.07: [23359]: REMOTE wants 4800 bit/s
Oct 03 22:18:06.07: [23359]: REMOTE wants page width 1728 pixels in 215
mm
Oct 03 22:18:06.07: [23359]: REMOTE wants unlimited page length
Oct 03 22:18:06.07: [23359]: REMOTE wants 3.85 line/mm
Oct 03 22:18:06.07: [23359]: REMOTE wants 2-D MR
Oct 03 22:18:06.07: [23359]: --> [7:CONNECT]
Oct 03 22:18:06.07: [23359]: RECV: begin page
Oct 03 22:18:06.07: [23359]: RECV: send trigger 022
Oct 03 22:18:06.07: [23359]: <-- data [1]
Oct 03 22:19:00.74: [23359]: RECV: 32736 bytes of data, 829 total lines
Oct 03 22:19:10.58: [23359]: RECV: 5962 bytes of data, 1082 total lines
Oct 03 22:19:11.99: [23359]: --> [16:+FPS:1,441,0,0,0]
Oct 03 22:19:11.99: [23359]: --> [6:+FET:0]
Oct 03 22:19:11.99: [23359]: RECV recv MPS (more pages, same document)
Oct 03 22:19:11.99: [23359]: --> [2:OK]
Oct 03 22:19:12.02: [23359]: RECV send MCF (message confirmation)
Oct 03 22:19:12.02: [23359]: RECV FAX (00000082): from 0164258126, page
1 in 1:12, INF, 3.85 line/mm, 2-D MR, 4800 bit/s
Oct 03 22:19:12.02: [23359]: <-- [7:AT+FDR\r]
Oct 03 22:19:16.80: [23359]: --> [7:CONNECT]
Oct 03 22:19:16.80: [23359]: RECV: begin page
Oct 03 22:19:16.80: [23359]: RECV: send trigger 022
Oct 03 22:19:16.80: [23359]: <-- data [1]
Oct 03 22:20:11.53: [23359]: RECV: 32727 bytes of data, 860 total lines
Oct 03 22:20:19.59: [23359]: RECV: 4878 bytes of data, 1077 total lines
Oct 03 22:21:38.42: [23359]: CLOSE /dev/ttyS0
================================================================
MOMDEM CONFIG
================================================================
#
# Generic Class 2.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 31
AreaCode: 164
FAXNumber: "+31 xxx xxxxx"
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: MY NAME
LogFacility: hylafax
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 50
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use this to supply a hint
#ModemRate: 19200 # max rate for DCE-DTE
communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier
(or not)
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s # T for tone dialing
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem
is reset
#ModemAnswerCmd: ATA # use this to answer
phone
#ModemNoFlowCmd: AT&K # disable flow control
cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command
results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook
(hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemSoftResetCmdDelay: 3000 # pause after soft reset
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2
seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received
facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for
transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D
(direct)
Class2CQCmd: "" # commands to enable copy
quality proc.
Class2AbortCmd: AT+FKS # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality
capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FPP=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command
hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd: AT+FIE=0 # disable interrupt-enable
command
Class2PTSCmd: AT+FPS # set post-page status command
Class2PTSQueryCmd: AT+FPS? # set post-page status query
command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control
command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control
command
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
